Steam of 6 MPa and 400-C produced in a boiler at a flow rate of 0.aa6 m³/sec is passed through a turbine, after which it becomes a saturated vapor and its pressure drops to 60kPa. The heat loss from the turbine to the environment of 37°C is bb kJ/kg. Obtain: a) The power produced in the turbine. b) The maximum power that could be produced. c) The second law efficiency of the turbine. d) The irreversibility associated with this process. aa=04,bb=25

Steam of 6 MPa and 400-C produced in a boiler at a flow rate of 0.aa6 m³/sec is passed through a turbine, after which it becomes a saturated vapor and its pressure drops to 60kPa. The heat loss from the turbine to the environment of 37°C is bb kJ/kg. Obtain: a) The power produced in the turbine. b) The maximum power that could be produced. c) The second law efficiency of the turbine. d) The irreversibility associated with this process. aa=04,bb=25

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pls. answer thank you! In a 13 MW geothermal power plant, the mass flow of steam entering the turbine is 30 kg/s. The quality after throttling is 23% and enthalpy of ground water is 730 KJ/kg. Determine the overall efficiency of the plant.
3. Steam enters the turbine at the rate of 1.5 kg/s with enthalpy of 2300 kJ/kg and exhaust enthalpy of 1200 kJ/kg. Steam is extracted from the turbine at a rate of 0.87 kg/s for heating purposes with enthalpy of 2570 kJ/kg. What is the turbine work, in HP?
In a natural gas pipeline compressor, 110 m3/min. propane is compressed polytropically. The inlet pressure is 101 kPaa and the temperature is 38 0 The process follows pV1.08 = C. The exit pressure is 510 kPaa. Determine (a) the exit temperature, (b) the mass flow rate, (c) the heat loss, and (d) the work required.
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
A pump operates at 600 W, the mass flow rate of the liquid is 1 kg/s, at the inlet the fluid is stagnate, and velocity at exit is 12 m/s, the mechanical efficiency of the pump is: Select one: a. 0.90 b. 0.91 c. 0.92 d. 0.89
A fluid enters an apparatus at 480 ft/s, initially the pressureof the fluid is 120 psia, the specific volume of 5ft3/lb andthe internal energy is 383 BTU/lb. The fluid leaves theapparatus at 25psia, specific volume of 18 ft3/lb, an exitvelocity of 1200 ft/s and internal energy of 120 BTU/lb. Theheat radiation loss is 10 BTU/lb. Determine work steadyflow, WSF
7.15. A steam turbine operates adiabatically at a power level of 3500 kW. Steam enters the turbine at 2400 kPa and 500°C and exhausts from the turbine as saturated vapor at 20 kPa. What is the steam rate through the turbine, and what is the turbine efficiency?
Air enters a turbine at 900K and leaves at 300K. The turbine shaft is connected to a generator with an efficiency of 80%. If the mass flow rate of air through the turbine is 150kg/s, what is the electrical power produced by this turbine generator?
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
An ammonia compressor operates on an evaporator pressure of 291.57 kPa and a condenser pressure of 1557 kPa. A Heat Exchanger is installed thus superheating the refrigerant by 100C and a subcooling by 50 C. The system is used to cool water at 2 kg/s from 250 C to 150 C. Given: h1=1476 kJ/kg , h2=1752 kJ/kg . Determine the ff: a.) mass flow of reffrigerant. kg/s b.) compressor work. kw c.) mass flow of cooling water needed in the condenser for a temp. drop of 180F. kg/s
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
Water vapor enters an adiabatic turbine at a pressure of 8 MPa, a temperature of 600 ℃ and a speed of 100 m/s, and then a pressure of 50 kPa exits at a temperature of 150 ℃ and a speed of 160 m/s. The turbine power is 10 MW. According to this; a) The steam flow rate from the turbine b) Do you find the isanthropic efficiency of the turbine?