steel beam cross section is assembled as shown by bolting the channel, C200 x 27.9, through its web on the wide flange, W200 x 35.9. The beam is 4 m in span and is simply supported loaded with a uniformly distributed load of intensity 20 kN/m throughout its span and a concentrated load, P (refer to the given table), at the midspan. If the diameter of the bolts is 22 mm, Compute for the moment of Inertia of the cross section Determine the maximum bending stress in the beam. Calculate the spacing of bolts (pitch) if the allowable shearing stress for a bolt is 100 MPa.

steel beam cross section is assembled as shown by bolting the channel, C200 x 27.9, through its web on the wide flange, W200 x 35.9. The beam is 4 m in span and is simply supported loaded with a uniformly distributed load of intensity 20 kN/m throughout its span and a concentrated load, P (refer to the given table), at the midspan. If the diameter of the bolts is 22 mm, Compute for the moment of Inertia of the cross section Determine the maximum bending stress in the beam. Calculate the spacing of bolts (pitch) if the allowable shearing stress for a bolt is 100 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 6.96.9 mm long simply supported wood beam carries a uniformly distributed load of 10.810.8 kN/mkN/m, as shown in Figure A. The cross-sectional dimensions of the beam as shown in Figure B are b=195b=195 mmmm, d=490d=490 mmmm, yH=80yH=80 mmmm, and yK=158yK=158 mmmm. Section a–a is located at x=1.4x=1.4 mm from B. (a) At section a–a, determine the magnitude of the shear stress in the beam at point H. (b) At section a–a, determine the magnitude of the shear stress in the beam at point K. (c) If the allowable shear stress for the wood is 950950 kPakPa, what is the largest distributed load ww that can be supported by the beam?
A 7.5 m long simple span beam as shown below supports a deadload andliveload throughout its entire length. If the following loads and materialproperties are given:DL = 18 kN/m LL = 25 kN/mfc’ = 25 MPa fy = 390 MPaa. Determine the factored moment carried by the beam.b. Determine the location of the neutral axisc. Determine the number of 36 mm ø bars needed for the beam.
A simply supported beam with a span length of 4.8 m is laterally supported atits ends and is subjected to a dead load = 8 kN/m (including the weight of thebeam) and live load = 10 kN/m. If Fy = 345 MPa, is a PIPE8SCH80adequate?
Topic : Uncracked and cracked section 1. A beam has a width of 300mm and effective depth of 540mm, d’ = 60mm. It is reinforced with 4 – 25mm diam tension bars and 2 – 25mm compression bars. f'c = 28mpa and fy= 420. What is the ultimate moment capacity of the beam?
Calculate the required steel area for a reinforced concrete T-beam with an effective flange width of 1200 mm and a slab thickness of 100 mm. The beam is to carry an ultimate moment of 1300 kN-m. The width of the web is 300 mm and the effective depth is 550 mm. Assume f’c = 28 MPa and fy = 400 MPa * a. 7772 mm² b. 8256 mm² c. 7932 mm² d. 7232 mm²
An eight meter simply supported beam carries a superimposed dead load of 6kN/m and aservice live load of 15kN/m. The beam has a width and total depth of 400mm and 550mm respectively.It is reinforced with five diameter 25mm bars and 10mm stirrups. Material properties are fc'=27.60MPaand fy=421.60MPa. 1. Using the detailed calculation of Vc, required spacing of stirrups at 1.20m from the support using the NSCP 2015 provisions.
A rectangular beam having a width of 250 mm has a total depth of 450 mm. It 0/1 is reinforced at the bottom with a total steel area of 1875 sq.mm. placed at an effective depth of 375 mm. fc'=27.6MPa and fy=414.7 MPa. If the beam has a simple span of 6m, determine the safe live load thet the beam could carry in addition to the dead load including its own weight of 20 kN/m? (Please answer in an encoded form for better understanding)
A T-beam that traverses the center of a floor system for which bw = 300mm and d=550 mmm. The beams are 4.8 m long and spaced at 3 m on center and the slab thickness is 100mm. Determine the required steel area if the dead load moment including its own weight is 400 kN-m, live load moment is 500 kN-m, f'c = 28 Mpa and fy = 414 Mpa.
A reinforced concrete rectangular beam has a width of 315mm and an effective depth of 525mm. The beam is reinforced with six 25mm diameter tension bars. Take fy=400MPa and fc=29.50MPa. What is the nominal moment capacity of the beam, kN-m? What is the balanced steel area, mm2?
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS Draw the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the shear force 3.5 m to the right of point A if W = 9.9 kN/m, T = 14.75 kNm, m = 11.1 m, and n = 5.9 m. Round off the final answer to four decimal places.
A 550mmx800mm column reinforced with 12 pcs of D20mm (3 bars each on outer ends). The column carries an ultimate load of 3500kN at an eccentricity 325mm. Assuming concrete strength and steel strength to be 25MPa and 420MPa respectively. Take clear cover to be 40mm and diameter of ties to be 10mm. Determine the balanced compression depth, mm. Determine the balanced moment, kN-m. What is the design strength, kN.
calculate the nominal shear strength(kN) of 4-legged stirrups 12 mm diameter, spaced at 280 mm on centers fo a beam with effective depth of 417 mm. use yield strength of stirrup fy = 275 Mpa.