Steel pulleys, 120 mm and 530 mm in diameter are to transmit 2.50 kW at 1100 rpm of the smaller pulley, through a single ply oak tanned leather belt. Use a coefficient of friction of 0.35 for oak tanned leather belt, allowable stress of 2.8 MPa, distance between shafts is 3000 mm and belt thickness of 3.215mm. Determine the ratio of net tension.

Steel pulleys, 120 mm and 530 mm in diameter are to transmit 2.50 kW at 1100 rpm of the smaller pulley, through a single ply oak tanned leather belt. Use a coefficient of friction of 0.35 for oak tanned leather belt, allowable stress of 2.8 MPa, distance between shafts is 3000 mm and belt thickness of 3.215mm. Determine the ratio of net tension.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.15P: Solve the preceding problem for a welded Tank with a = 62°,r = 19 irM = 0.65 in.,p = 240 psu E = 30...

See similar textbooks

Similar questions

An overhang hollow shaft having inside diameter 0.5 time outside diameter, carries a cast iron pulley having 800N weights and 900mm diameter, at 250mm from the nearest bearing. The pulley is driven by another pulley mounted on the shaft placed bellow it, to transmit 35kW at 400r.p.m. The belt ends are vertical and parallel; if the ratio of tensions in belt is 3 and the permissible shear stress for material of shaft is limited to 200MPa, determine the diameters of shaft.
A safety valve, 11 mm in diameter, is to blow off at a pressure of 1.5 MPa. It is held on itsseat by means of a helical compression spring, with initial compression of 16 mm. Themaximum lift of the valve is 27 mm. The ratio of mean coil diameter to wire diameter is5. The spring is made of cold drawn steel wire with ultimate tensile strength of 1400 MPa. (G = 81 370 N/mm2), Calculate:i. Wire diameter;ii. Mean coil diameteriii. Number of active coilsiv. Free lengthv. Pitchvi. Actual spring constantvii. Required Stiffness
Q2 ) A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch.
A cone clutch is to transmit 10 KW at 600 r.p.m. the cone has aface angle of 10◦The width of the face is halfe of the mean radius and the max pressureis 0.1 N/mm²Assuming uniform wear and the coefficient of friction is 0.3, find theinner and outer radius and the axial force required on the clutch. Subject: Theory of Machines
Two shafts, one solid the other one hollow, are connected end to end by meansof a coupling in which there are 8 screws on the pitch diameter D = 250 mm.The solid shaft has diameter d = 50 mm and transfers the power P = 500 kW at 75 rev/s.The external diameter of the hollow shaft is dex = 75 mm.Note: All parts of the system must be equally strong, and able to transfer the requiredpowerCalculate:(a) The internal diameter di of the hollow shaft(b) The diameter of the bolts db connecting the two shafts(c) If the hollow shaft has to be replaced by a rectangular hollow cross-section withouter dimensions b x h and uniform wall thickness of 4 mm.Calculate the values b, h while following the request to keep h = 2b
A drive shaft running at 2500 rpm has outer diameter of 80mm and innerdiameter of 60mm. The allowable shear stress in the shaft is 40MPa. Determine themaximum power that can be applied.
A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces has worn away by 1.25 mm. find the maximum power that can be transmitted assuming uniform wear. A plate clutch has 3 discs on the driving shaft and 2 discs on the driven shaft, providing four pairs of contact surfaces. The outside diameter of the contact surfaces is 240 mm and inside diameter 120 mm. Assuming uniform pressure and coeff. Of friction is 0.3. Find the total spring load pressing the plates together to transmit 23kw power at 1475 revolution per minute. If there 6 springs each of stiffness 13 kN/m and each of the contact surfaces…
Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 165o and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted.
A flat belt, of density 1000 kg/m3 has a maximum permissible stress of 2·5 MN/m². Thebelt is 200 mm wide and 12 mm thick.(a) Determine the maximum power that can be transmitted if the ratio of tight-side toslack-side tension is 2. The diameter of the driving pulley is 900 mm and the required speed of the output shaft is955 rev/min(b) Taking the belt thickness into account, determine the required diameter of theoutput pulley. (c) What would the required diameter be, assuming a total slip of 4%? (d) If the mass of the belt was neglected, explain the effect (with reasons) this wouldhave on the maximum power calculated in (a)
Compute for the induced compressive stress in kPa, of a steel shafting of 59 mm diameter and 954 m in length that issubjected to an increase of temperature of 88ºC. Use 6.5x10-6/F, E = 30x106 psi.
An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 mapart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted
A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the face ishalf of the mean radius and the normal pressure between the contact faces is not exceeding0.09Nmm2⁄. Assuming uniform wear and the coefficient friction between contact faces as 0.2. Find themain dimensions of the clutch and the axial force required to engage the clutch.