Stem of Q. 9 and 10 Figure shows inverted T shaped fixed pipe. Liquid is released from rest from position shown. Liquid is non viscous. Q.9 Area = A Q.10 H Area = 2A H H ទ Area = A Velocity of fluid in vertical part of the tube, when level of liquid in it becomes value of p is equal to HA will be √gH.1 . The Acceleration of fluid particles in vertical tube just after releasing the fluid will be, where q is equal to 9

Stem of Q. 9 and 10 Figure shows inverted T shaped fixed pipe. Liquid is released from rest from position shown. Liquid is non viscous. Q.9 Area = A Q.10 H Area = 2A H H ទ Area = A Velocity of fluid in vertical part of the tube, when level of liquid in it becomes value of p is equal to HA will be √gH.1 . The Acceleration of fluid particles in vertical tube just after releasing the fluid will be, where q is equal to 9

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Similar questions

A pipe carrying oil of sp gr 0 877 changes in A pipe carrying oil of sp gr 0.877 changes in size from 150mm at section E to 450mm at section R Section E is 3 66m lower than R section R. Section E is 3.66m lower than R and the pressures are 91.0kPa and 60.3kPa, respectively. If the discharge is 0.146m3 respectively. If the discharge is 0.146m /s, determine the lost head and the direction of flow.
An inverted differential manometer is connected to two pipes A and B whichconvey water. The fluid in manometer is oil of specific gravity of 0.8. For themanometer readings r = 30 cm, s = 20 cm and t = 30 cm, find the pressuredifference between A and B.
Water piping A circular pipe used to discharge water from one reservoir to another reservoir (picture) The fluid is assumed to be viscous. 1. Determine the flow rate and the pressure as A ( consider all head losses). 2. Diameter of the pipe D=6 cm, roughness heigh of the pipe k=0,15cm, minor loss coefficients K1=0,5, K2=K3=K4=K5=1, K6=10, K7=1, kinematic viscosity of water =10^-6 m2/s
oil (SG = 0.88) dischargesfrom a pipe (D = 13 in.) through a sharp-crested, round orifice (diameter = 5 in.), as shown. the coefficients of contraction and velocity are 0.619 and 0.967, respectively. find the actual velocity (in ft/s) in the jet. Point (1) is a point collinear with the orifice at point (2). Point (3) is the free surface of the manometer containing mercury. use h = 2.84 ft., and y = 7.42 in.
Water piping A circular pipe used to discharge water from one reservoir to another reservoir. The fluid is assumed to be viscous. Determine the flow rate and the pressure as A ( consider all head losses). Diameter of the pipe D=6 cm, roughness heigh of the pipe k=0,15cm, minor loss coefficients K1=0,5, K2=K3=K4+K5=1, K6=10, K7=1, kinematic viscosity of water =10^-6 m2/s
Question-02:(CLO2)(10)A closed container containing water up to a height of 3.0 meter and air at the upper part with an orifice of 100 mm at its bottom. If 50% of the air is being removed from the upper part of the container by suction then Estimatedischarge passing through the orifice using Bernoulli’s equation if Cd=0.62.
For a vertical rectangular gate, one side has linseed oil (0.938) and the other has two fluids - castor oil (0.96) and water. Considerinh a unit-width of the gate, apoly the PRESSURE PRISM CONCEPT (Illustrate and label the pressure diagram/prism) to calculate the magnitude and direction of the following when z = 20ft.
Water flows through the orifice meter shown in Fig. P8.123 at a rate of 0.10 cfs. If d= 1ft, determine the value of h. Co= 0.616.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. A. 12.9517 B. 39.5136 C. 99.9358 D. 30.4889 What gage pressure p1 in kPa, is needed to provide the given flow rate? A. 1121 kPa B. 1725 kPa C. 1692 kPa D. 1328 kPa
Water enters the bottom of the cone in Fig. P3.24 at auniformly increasing average velocity V = Kt . If d is verysmall, derive an analytic formula for the water surface rise h ( t )for the condition h = 0 at t = 0. Assume incompressible fl ow.
A reservoir contains water has a vertical circular orifice 25.2mm diameter and is first plugged up to measure any displacing force, the tank is suspended in a particular way. The horizontal force is required to keep the tank in place on the removal of the plug. The opposite applied force to the orifice is 16.8N. The volume per time was found as 141lt/minute. It is assumed that the level of the water is maintained at a constant height of 2.785m above the orifice. Calculate Cc, Cv, and Cd for the orifice.
Obtain the gage pressure at the center A of the pipe shown. Neglect surface tension effects. For Liquid 1 specific gravity= 1.5, for liquid 2 specific gravity= 3.2, h1=15cm, h2= 30cm,h3=75cm