Quèstion 43Find the total distance (m) traveled by a car from the time he saw a hazard until he applied the brakes. He was travelling at 59 kph with perception-reaction time of 2.4 seconds. Theskid resistance is 0.18 with 86% efficiency: Express your answer in 2 decimal places«< Question 43 of 50 >> A Moving to another question will save this.response.acerDelHomeF7F8F9F10F11F12PrtScF4F5FGScr LkSysRqBreakasnedInsF2-&*Backspac%5€78WRUDFGH

Answered: Image /qna-images/answer/427aba66-7b8c-4981-bad7-a771f95b850c.jpg

stion 43 Find the total distance (m) traveled by a car from the time he sawa hazard until he applied the brakes. He was travelling at 59 kph with perception-reaction time of 2.4 seconds. The skid resistance is 0.18 with 86% etticiency: Express your answer in 2 decimal places

stion 43 Find the total distance (m) traveled by a car from the time he sawa hazard until he applied the brakes. He was travelling at 59 kph with perception-reaction time of 2.4 seconds. The skid resistance is 0.18 with 86% etticiency: Express your answer in 2 decimal places

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A = 1.94.hmax = 0.559.R = 206 1. Filling the tank (30%)a) If the tap on the output pipe is closed (i.e. R = ∞) determine how long it will take the tank to fillup assuming qi = 0.001 m3/s.b) If the tap on the output is open liquid will be coming out at the same time as liquid is going in. Ifthe flow rate in is bigger than flow rate out the height of the liquid in the tank will rise. Using theR value given on the Results Sheet, determine the steady state height of liquid in the tankassuming qi = 0.001 m3/s.c) In theory it will take an infinite amount of time to achieve steady state so in practice we define thetime to respond as the 95% settling time (i.e. the time taken to get to within 5% of the steady stateoutput.) Measure the 95% settling time from your simulation in Q1b). 2. Emptying the tank (10%)a) Assuming the tank is initially full (i.e. h(0) = hmax) and the input is turned off (i.e. qi = 0) the tank willstart to empty. Assuming the R value in Q1b), determine the time…
A block of wood 0.70 m x 0.70 m x h meters in dimension was thrown into the water and it floats with 0.19 m projecting above the water surface. The same block was thrown into a container of a liquid having a specific gravity of 0.90 and it floats with 0.15 m projecting above the surface. Determine the value of h. Unit of the Correct Answer: meter Decimal Places required in the final answer: 2
A car traveling at a certain speed saw an obstruction ahead. The reaction time is 2.8 s, compute the car’s speed in kph if the distance traveled is 72.2 m. a. 97.52 b. 92.83 c. 85.26 d. 79.51
34 Find the total distance (m) traveled by a car from the time he saw a hazard until he applied the brakes. He was travelling at 37 kph with perception-reaction time of 1.5 seconds. The skid resistance is 0.23 with 86% efficiency. Express your answer in 2 decimal places.
An open tank 30 ft long by 4 ft wide by 4 ft deep is filled with 3.25 ft of oil, s = 0.822. It is accelerated uniformly from rest to 45 ??⁄???. What is the shortest time in which the tank can be accelerated without spilling any oil?
Can Please Help Me: Civil Engineering 60 minutes only the given time. Wish you could help me. I will give UPVOTE and GOOD FEEDBACK. //Question A 2-foot diameter pipe carries stormwater discharge from a site. The concrete pipe was designed with a slope of 0.8 foot per 90 feet. At the time of measurement, the pipe has 0.8 feet of discharge flowing in it. What is the pipe discharge? (Express your answer in liter per second). Ans.205.1 lps //Question
Can Please Help Me: Civil Engineering 60 minutes only the given time. Wish you could help me. I will give UPVOTE and GOOD FEEDBACK. //Question A rectangular shaped channel is 1 foot wide and average depth in the channel is measured to be 0.4 feet deep. For a 50 feet long section, an orange float traveled from one end to the other in 57 seconds, 48 seconds and 64 seconds. What is the streamflow discharge, in gallon per minute, if the correction factor is 0.80? [Ans. 130gpm] //Question
Choose the correct answer in the choices with solution Thank you i need asap after 10minutes mwa.
Questions #1 The water system in a suburban area consists of old 9-inch pipeline 2,280 ft. long which conveys water from a pump to a reservolr whose water surface as 326 ft. higher than the pump. Water is pumped at the rate of 3.09 cfs. Determine the horsepower saved by replacing the old pipe with a new 12-inch pipe. Assume the values of f as equal to 0.050 and 0.012. respectively, for the old and new pipes. Neglect Losses of head except friction head. A. 38.17 B. 42.89 C. 50.27 D. 54.56 Questions #2 A new cast iron pipe must carry 3.945 mm/s at a head loss of 9.8 m per 4 km length of pipe. Compute the diameter of the pipe in m using Darcy Weishback Formula with f = 0.038. A. 1.98 B. 2.062 C. 1.744 D. 1.819
Choose the correct answer in the choices with solution thank you! I need asap after 5minutes thank you so much
The specific gravity of the manometer fluid shown in the diagram is 1.07. Determine the volume flowrate, Q, if the flow is inviscid and incompressible and the flowing fluid is (a) water, (b) gasoline, or (c) air at standardconditions.
1) Chlorine contact tank (Wastewater Treatment) An activated sludge plant has a design flow (average daily flow) of 11 MGD. Determine dimensions of chlorine contact tank. The design parameters: use 1 tank. depth = 10 ft, rectangular tank: L = 4 W detention time = 15 min (based on maximum hourly flow, Q = 3 x average flow rate) I have an answer for this problem however im confussed on it. I posted is an image of the first step (solving for V) Where does the17.02 come from. I understand the (3)(11)(15) and (60) but where does the 17.02 come from?? Image 2 for problem 2 2) Chlorine contact tank (Wastewater Treatment) An activated sludge plant has a design flow (average daily flow) of 11 MGD. Determine dimensions of chlorine contact tank. The design parameters: use 1 tank. depth = 10 ft, rectangular tank: L = 4 W detention time = 15 min (based on maximum hourly flow, Q = 3 x average flow rate) I have an answer for this problem however im confussed on it. I posted is an image of…