Please answer this, THank you Suppose we calculated the value of V, in thefigure below. Can we use this value to theequation = pAV to determine the massflow rate? Explain.Stagnationpoint

A pitot tube is used to measure the local velocity and it is also used to determine the total head…

Answered: Suppose we calculated the value of Vị…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compute stagnation enthalpy of air at normal conditions (P=1atm, T=300K) moving with velocity of 1398 m/s. What temperature of air we will observe?
Q3/ Air at 200 kPa, 100 °C, and Mach number Ma=0.8 flows through a duct. Calculate thevelocity, the stagnation pressure and the stagnation temperature of the air.
Each stage of an axial-flow compressor is 0.5 reaction,, has the same blade speed and the same flow outlet angle of 30 deg relative to the blades. the mean flow coeficcient is constant for all stages at 0.5. At entry to the first stage the stagnation temperature is 278 K, the stagnation pressure 101.3 kPa, the static pressure is 87.3 kPa and the flow area 0.372 m2. Using compressoble flow analysis determine the axial velocity and the mass flow rate. Determine also the shaft power needed to drive the compressor when there are 6 stages and the mechanical efficiency is 0.99.
Air enters a compressor at a stagnation state of 100 kPa and 27 ∘C. If it has to be compressed toa stagnation pressure of 900 kPa, calculate the power input to the compressor when the massflow rate is 0.02 kg s−1. Assume the compression process to be isentropic.
Air at P1 = 1 MPa, T1 = 600 °C and V1 = 150 m/s enters a converging nozzle. The exit area is A2 = 50 cm2 and the back pressure is P2 = 0.7 MPa. What is the mass flow rate (kg/s) through the nozzle? What the is Mach number at the nozzle exit? What would be the flow rate you calculate if you assumed isothermal flow?
Air at 800 kPa and 1200 K enters a converging nozzle with negligible velocity (i.e., these are stagnation or total values). The throat area of the nozzle is 10 cm?. Calculate and plot the exit pressure, exit velocity, and mass flow rate versus back pressure (exit pressures) from 100 kPa to 800 kPa by 100 kPa.
Air enters a converging- diverging nozzle at a pressure of 830 kPa abs and a temperature of 32°C. Neglecting the entrance velocity and assuming a frictionless process, find the Mach number at the cross-section where the pressure is 240 kPa abs.( for air: k = 1.4 R=287J/kgK)
A malfunctioning jet aircraft has an engine working at 10,000 m and producing an internalstagnation pressure of only 210 kPa and a stagnation temperature of 1500 C. The area of thethroat is 0.05 m² and the exit area is 0.2m². What is the momentum of the air leaving thisengine?
Air with stagnation pressure of 800 kPa and temperature of 100⁰C ,is expanded isentropically to the channel 1 where A₁ = 20 cm² and P₁ 47 kPa. Count: a. Ma1 b. The area of the throat / neck (the narrow part) of the channel c. Mass flow rate m d. In part 2 which is located between the throat/neck with part 1, where the area of part 2 is 9 cm² ,calculate Ma2
1. Air, with stagnation conditions of 800 kPa and 100 °C, ex pands isentropically to a section of a duct where A₁ = 20 cm² and p₁ = 47 kPa. Compute ( a ) Ma₁ , ( b ) the throat area , and ( c ) m . At section 2 between the throat and section 1, the area is 9 cm². (d) Estimate the Mach number at sec tion 2. Plz sketch and solve it
Air, with stagnation conditions of 800 kPa and 100°C, ex pands isentropically to a section of a duct where A_{1} = 20 cm² and p_{1} = 47kPa . Compute (a) Ma₁, (b) the throat area, and (c) m. At section 2 between the throat and section 1, the area is 9 cm². (d) Estimate the Mach number at section 2.
Each stage of an axial flow compressor is of 0.5 reaction, has the same mean blade speed and the same flow outlet angle of 30 degree relative to the blades. The mean flow coefficient is constant for all stages at 0.5. At entry to the first stage the stagnation temperature is 278 K, the stagnation pressure 101.3 kPa, the static pressure is 87.3 kPa and the flow area 0.372 m. Using compressible flow analysis determine the axial velocity and the mass flow rate.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Suppose we calculated the value of Vị in the figure below. Can we use this value to the equation = pAV to determine the mass flow rate? Explain. Stagnation point