Suppose we have planned to design a hydraulic system.ln this aspect, the pump selection is to be finalized for a flow rate of 3907 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 4.4 m/s and 6.92 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines. (b) Write the significance of using minimum diameter pipelines in the hydraulic system

Suppose we have planned to design a hydraulic system.ln this aspect, the pump selection is to be finalized for a flow rate of 3907 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 4.4 m/s and 6.92 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines. (b) Write the significance of using minimum diameter pipelines in the hydraulic system

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.34P

See similar textbooks

Similar questions

Suppose we have planned to design a hydraulic system.In this aspect, the pump selection is to be finalized for a flow rate of 3299.5 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 3.6 m/s and 6.92 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines Area of the maximum sized pipe diameter (in m2) Area of the minimum sized pipe diameter (in m2) The minimum sized pipe diameter (in cm) and The maximum sized pipe diameter (in cm)
Suppose we have planned to design a hydraulic system.In this aspect, the pump selection is to be finalized for a flow rate of 3464.5 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 4.6 m/s and 6.8 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines. Write the significance of using maximum diameter pipelines in the hydraulic system
Example: A fan of diameter 0.7 m running 1500 rpm delivers 140 m3/min of air at 15C against 75 mm of water total pressure when the total effeciency is 86%. Determine the volume of air delivered, total pressure and power consumed, if (a) the air temperature is 50C. (b) the air temperature is 50C and the fan speed is 1700 rpm. (c) the same conditions as (b) but a 0.6 m diameter, geometrically similar fan is used.
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Consider a venturi with a throat-to-inlet area ratio of 0.8, mounted on theside of an airplane fuselage. The airplane is in flight at standard sea level.If the static pressure at the throat is 2100 lb/ft2, calculate the velocity ofthe airplane.
Aiming a 1.69 in diameter garden hose straight up, forms a “bubbler fountain” that you could easily drink from (but you shouldn’t because of bacteria, etc.). The water flows out the hose and down the sides. If the water has a density of 63.1 lbm/ft^3 and a viscosity of 0.0119 g/cm*s, what is the thickness of the water film (df) (in cm) if the flow rate of water is 6.42 in^3/s? For simplicity, assume the film is thin enough that you can use rectangular coordinates.
Solve problem 2 (Textbook, p. 230). This is a case example how to use the characteristic curve of a pump to find the operation point of a piping installation. You can find the solution graphically, iteratively (if you want to fit the curve of Fig. P4.2 with an equation) or using trial and error (my recommendation). 2. Pump and pipeline—M . The head/discharge curve of a centrifugal pump is shown in Fig. P4.2. The exit of the pump is connected to 1,000 ft of nominal 2-in. diameter horizontal pipe (D = 2.067 in.). What flow rate (ft^3/s) of water can be expected? Assume atmospheric pressure at the pump inlet and pipe exit, and take fF = 0.00475.
Darcy's law does not incorporate friction loss because? a) The Zubov constant prevents it. b)There is no significant friction loss c)Darcy's law does consider friction just like the Darcy's earlier pipe flow equation on pipe flow that he developed with Weisbach, d) Pressure head is always very high. e) Flow velocity in porous matrix is negligible compared to the effect of hydraulic gradient.
please answer A pump impeller rotating at 1400 rpm has an outside radius of 21 cm, the vane outlet angle β2 is 158° and the radial velocity at the outlet Cr2 is 4 m/s. Assuming radial flow at inlet, draw the theoretical outlet velocity diagram and calculate the various velocities and angles.( A)What is the theoretical head Ho, in meters, assuming that the circulatory flow coefficient η∞ = 1.,(B)In the preceding example; assume a deviation of 10° applied to β2 due to circulation after the modern theory. The flow is 30 lit/s. After drawing/illustrating the velocity diagram, find the theoretical head Ho, in meters, assuming radial flow at inlet, neglecting the deviation in inlet velocity diagram. (c)Assuming that the mechanical efficiency ηmech = 0.95, the hydraulic (or manometric) efficiency ηman = 0.8, find the required break horsepower to drive the pump.
Air flows through a duct at 2,700 cubic feet per minute (CFM). After several feet and a few vents, the air-flow decreases to 1,890 CFM. What is the percent drop that has occurred? (Simplify your answer completely.)
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (2) Select all energy loss types between section 1 and 2_________ A. Minor loss for the two elbows B. Friction loss in suction line C. Minor loss for Valve 1 D. Entrance loss E. Exit loss F. Friction loss…
The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (1) Select the simplified general energy equations for section 1 and 2_________ A. B. C. D.
A viscous fluid of density 900 kg/m3and viscosity 0.3 Pa.s flows in a horizontal smooth pipe of diameter 0,06 m and length 9,8 m. Flow Reynolds Number is 802. Use pi number , π = 3.14 and gravitational acceleration, g =9.81 m2/s a) What is the magnitude of mean velocity (in m/s)? b) What is the magnitude of friction coefficient ? c) What is the magnitude of pressure gradient to induce flow (in Pa/m )? d) What is the magnitude of shearing stress over the pipe surface in (Pa) ?