hud Tank1 エ,,R、 -Is,R3 Tank 2 h2, Cz A generic fluid system is shown. Inertances in the channels of flow are given as 11,12, and I13. Each channel also has corresponding resistances of R1,R2, and R3. Tank 1 and Tank 2 have capacitances C1 and C2 with corresponding tank heights h1 and h2, respectively. Äfter labeling pressure and flow variables as appropriate, derive a complete mathematical model using these variables.

hud Tank1 エ,,R、 -Is,R3 Tank 2 h2, Cz A generic fluid system is shown. Inertances in the channels of flow are given as 11,12, and I13. Each channel also has corresponding resistances of R1,R2, and R3. Tank 1 and Tank 2 have capacitances C1 and C2 with corresponding tank heights h1 and h2, respectively. Äfter labeling pressure and flow variables as appropriate, derive a complete mathematical model using these variables.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. What is the volumetric flow rate between two plates if the top plate is pulled, while keeping the bottom plate stationary, and simultaneously imposing pressure p0 on the left endof the channel, and pressure p0 + ∆p (∆p > 0) on the right end of thechannel.
Water at 20°C is withdrawn from a reservoir by means of a siphon, as shown in the figure. For d=10cm and D= 16cm, Determine: a) the minimum flow rate that can be achieved without cavitation occurring in the piping system, and b) the maximum elevation of the highest point in the piping system to prevent cavitation. c) Also, comment on the ways to increase the maximum elevation of the highest point in the piping system to prevent cavitation. (The saturation pressure of water at 20°C is 2.33 kPa)
The height from the surface to the outlet aperture in a water filled container is 3 m. Theaperture is sharp edged with diameter 0.1 m. The discharge coefficient c d = 0.6. Find thefluid flow.
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
A pipeline has the following data at its two section A and B Item Section - A Section - B Diameter (cm) 30 45 Elevation (m) 10 16 Pressure (k Pa) 40 30 Kinetic energy correction factor, α 1.08 1.25Assume ahead loss equal to 20 times the velocity head of A and calculate the discharge of water through this pipeline when flowing from B to A.
Determine the available suction head of the pump that is taking a gasoline at 204°C at a closed tank with a pressure 585 kPa gauge. the specific gravity of gasoline is 0.78 and it’s vapor pressure is 620 kPa absolute. the loss in suction pipe is 0.60 m and the pump center line is located 3.60 m above the gasoline level A. 8.66m B. 3.67m C. 7.66m D. 4.47m
Two water reservoirs, A and B are 8km apart and are connected by a 750 mm diameter steel pipe( f=0.02). Reservoir A is 10 m higher than reservoir B. If the pressure at B is 4 kg/cm^2 greater than at A, determine the amount and direction of flow of water inside the pipe. Disregard minor losses.
Reservoir X (Elevation 369m) supplies water to reservoir Y (Elevation 195m) thru a 400 mm pipe. A turbine is installed in the same level with Reservoir Y. The total system flow is 220 gpm determine the the output power in Hp if the turbine is 65% efficient and the total headloss of the system is 4.5m.
The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.
Water at 20° C is siphoned from a reservoir as shown. For d = 8 cm and D = 16 cm, determine (a) the minimum flow rate that can be achieved without cavitation occurring in the piping system and (b) the maximum elevation of the highest point of the piping system to avoid cavitation. (c) Also, discuss the ways of increasing the maximum elevation of the highest point of the piping system to avoid cavitation.
The system consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged long-radius elbows, a fully open flanged globe valve, and a sharp exit into a reservoir. If the elevation at point 1 is 400 m, what gage pressure is required at point 1 to deliver 0.005 m3/s of water into the reservoir? Use the following: v = 1 x 10-6 m2/s Kentrance = 0.5 Kexit = 1 Kvalve = 6.9 f = 0.0316 γ = 9810 N/m3 Choices: 3.44 Mpa 1.02 MPa 3.48 Mpa 1.00 MPa None of the choices
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3