(Suuds - pin shorter. The outer s m. Find stiffness of inn
Q: Compute the minimum critical surface crack (edge crack) length if the fatigue life must be a minimum...
A:
Q: 1. The kinematic viscosity of kerosene is 9 = 2.39(10-6). Determine its viscosity in FPS units. At t...
A: Givenkinematic viscosity of kerosene ϑ=2.39×10-6 m2/sspecific gravity sgkerosene=0.810
Q: P3.12 The thin rod in Figure 3.43 always re- mains in contact with the leftmost cor- ner of the circ...
A:
Q: Neglect the diameter of the small pulley attached to body A and determine the magnitude of the total...
A:
Q: Consider the two-dimensional velocity field given by = (5+ a1x + b1y)i + (4 + a2x + b2y)3, where a1,...
A:
Q: . The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal befo...
A: Given:La=2 ftAa=0.4 in2Lb=3 ftAb=0.2 in2
Q: Compute the a) air to fuel ratio by weight, b) atomic ratio of H/C, and c) % excess air or % theoret...
A: ACCORDING TO THE GIVEN DETAILS
Q: installation. Overpressure in chamber A, from which water outflows by nozzles B, is ppA = 80 kPa. Ve...
A:
Q: 3. (20 pts.) The basketball passed through the hoop even though it barely cleared the hands of the p...
A: Find the time and hight at point B Va = 10 ft/sec
Q: Points A and B are 4800 m. apart along 60 cm. pipe diameter carrying water. B is 10 m. higher that A...
A:
Q: In multiple-grain locking, SIX mode is useful, but an exclusive and intention-shared (XIS) mode is o...
A:
Q: rove that, if a fluid experiences a pure rotation, the divergence of it's velocity is 0 and the curl...
A: If fluid components rotate around their axes while flowing along streamlines, the flow is rotation...
Q: a. How fast your car was traveling immediately before the brakes were applied b. The time required f...
A:
Q: What will be the length of given mild steel rod after applying 100 kips force/load ?. If the diamete...
A: Given, Force applied = P = 100 kips = 100 x 103 lb Diameter of rod = d = 0.5 in Length of rod = L = ...
Q: Mass of ball=2.1 kg Velocity of bas=2.2 m/s Determine kinetic energy
A: Given m = 2.1 kg V = 2.2 m/s
Q: Find the resultant of two forces equal to 50N and 30 N acting at an angle of60°
A: Given Forces F1= 50 NF2= 30 NAngle = 60 To find Resultant
Q: The equation of motion of a particle is s = 8t2 + 3t – 10, where s is in meters and t in seconds. Fi...
A: We have to determine the velocity at the point
Q: 5. First ball is released from rest. After 2.5 seconds, second ball is released with a velocity of 4...
A: Here we need to determine the time and distance
Q: A amne alenmónt is gubjeafed fo fhe foclaing biranial of sfrex: Ox=75 mpa Oy =15 mPq %3D てy35 mq she...
A: The calculated factor of safety (FOS).
Q: Problem 2 Determine the total time t (in hrs.) required to fill the spherical tank with liquid whose...
A: Given:s=2.5m=400 Kg/mind=4 m
Q: 7. Draw the crystallographic feature given below. a) [111] b) (220) c) (0110)
A: Given
Q: During inelastic collision of two particles, which one of the following is conserved ? 1. total line...
A: In all types of collisions, linear momentum is always conserved which means the total momentum of th...
Q: MIXING PROBLEM CONDITIONS: 1.) When start P.B (10.0) is pressed, Pump Motor No. 1 (Q0.0) is ON. 2.) ...
A: Here the diagram given is as follows For the motor and pump time on delay and the level sensor are g...
Q: A piston/cylinder contains water with quality 75% at 200 kPa. Slow expansion is performed while ther...
A:
Q: e magnitude of the force required to hold the plate.
A: Given; Diameter, D=60 mm, water jet strikes a plate containing a hole of; Diameter, d=40 mm= 0....
Q: Question 2: For the following truss structure (with members AB, BC, AD, DE, BE, CF and FG all of 60 ...
A: Find the force in memeber DE
Q: If the Poisson's ratio of an elastic material is 0.4, the ratio of modulus of rigidity to Young's mo...
A:
Q: A spring mass system is excited by a force F0 sin ωt. At resonance the amplitude was measured as 100...
A: Given Data The force acting is: F=Fosinωt The resonance amplitude is: x=100 mm The resonant frequen...
Q: 210 160 25 105 R38 105 160 40 20 50 90 140 140 R45 25 25 60 210 105
A:
Q: the brakes of your car at 8 fps^2 to slow it down until it stops. After 456 ft, your car has come to...
A:
Q: An ideal Otto cycle using air has the following conditions. At point 1; p = 145 psia and 80° F. The ...
A:
Q: Mass of ball=2.1 kg Velocity of bas=2.2 m/s Determine kinetic energy
A: Given data : Mass of ball= m Velocity of ball=V To find : Kinetic energy
Q: What will be the length of given mild steel rod after applying 100 kips force/load ?. If the diamete...
A: Given, Force applied = P = 100 kips = 100 x 103 lb Diameter of rod = d = 0.5 in Length of rod = L = ...
Q: During inelastic collision of two particles, which one of the following is conserved ? 1. total line...
A: Collisions occur when two particles having relative velocity come in contact with each other. There ...
Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the largest load...
A:
Q: A container 10 m wide and 10 m long contains water 2 m high and is accelerating to the right at a ra...
A:
Q: The figure below are 2 solid cylindrical bars joined together at point B. Find the required minimum ...
A:
Q: 3,600° The instantaneous angular velocity of the crank Q2A is counterclockwise. Q2A = 1.5 in. Find t...
A:
Q: A domestic refrigerator sits in a kitchen, switched on, with the refrigerator door wide open. The ki...
A: The energy taken by refrigerator is less than energy transferred to environment is high. Then the it...
Q: A ball is released from the bottom of an elevator which is traveling upward with a velocity of 6 ft/...
A:
Q: the height (in mm) of cross section from strength calculation h = ?
A: working stress = yeild stress/ factor of safety = 220/1.6 = 137.5 MPa
Q: Determine the hydrostatic force and its location by (a)integration method and (b)formula method.
A:
Q: closed system receives 175 kJ of energy by the work mode and 125 kJ by the heat mode. It is now requ...
A: we have to determine what process must be done to reset the system to its original state.
Q: The work required to compress a gas reversibly according to PV1.30 = C is 67,790 J if there is no fl...
A:
Q: 1. Situation: You are to determine the duration of the yellow light at a highway intersection. Assum...
A:
Q: Thirty kilograms of butane gas per minute burns with dry air inside a combustion chamber, giving pro...
A:
Q: A heat engine produces 200 kJ/s of mechanical power and operates at an efficiency of 10%. What would...
A: Given Data W=200 kJ/s Efficiency=10%
Q: Drive formula for increas in volume of a thin metalic sphere when if is subjected to an internal pr...
A:
Q: 4. Determine the internal normal force, shear force, and bending moment at point C in the beam. 10 K...
A: Answer: ◆ Internal Normal Force at C: NC = 0 kN. ◆ Shear Force at C: VC = 20 kN. ◆ Bending Moment at...
Q: Example 7. Knowing that at the instant shown block A has a velocity of 2 ft/s to the left and an acc...
A:
Step by step
Solved in 2 steps with 2 images
- Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29A bumping post at the end of a track in a railway yard has a spring constant k = 8.0 MN/m (see figure). The maximum possible displacement d or the end of the striking plate is 450 mm. What is the maximum velocity vmaxthat a railway car of weight W = 545 kN can have without damaging the bumping post when it strikes it?A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal aim AB (length b = 30 cm) and a vertical arm BC (length c = 20 cm) pivoted at point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer at C is controlled by two parallel springs, each having a spring constant k = 3650 N/m. that are attached to a threaded rod. The pitch of the threads is p = 1.5 mm. If the weight is 65 N. how many revolutions of the nut are required to bring the pointer back to the mark?
- In a compound helical spring, the inner spring is concentric with the outer spring, but is 9 mm shorter. The outer spring has ten coils of mean diameter 24 mm, and the wire diameter is 3 mm. Find the stiffness of the inner spring if an axial load of 150 N causes the outer spring to compress 18 mm. If the mean coil diameter for the inner spring is 15.94 mm, find the wire diameter of the inner spring when it has eight coils. Both the springs are made of the same material having G = 77 GPa.A square end compression helical spring has an operation load range of 3.5KN to 4.2KN.The deflection for the load range is 8mm and the spring index is 6.if the permissible shear stress and module of rigidity for the material of the spring are 380MPa and 90pa respectively, including the effect of the wire curvature. Design the spring by, determine (A)wire diameter (B) mean coil diameter (C) number of active turns (D)total number of turnsA closed-coil helical spring is to have stiffness of 900 N/m in compression with a maximum load of 45 N and a maximum shearing stress of 120 N/mm2.The length of the spring is 45 mm. find the wire diameter, mean coil radius and the number of coils. Take C= 40000 N/mm2
- Figure 1.29 shows the suspension system of a freight truck with a parallel-spring arrangement. Find the equivalent spring constant of the suspension if each of the three helical springs is made of steel with a shear modulus G = 100 GPaand has 10 effective turns, mean coil diameter D = 50 cm, and wire diameter d = 5 cmA helical compression spring is required to provide a minimum force of 150 lb at installation and have a working deflection of 1 in. The spring rate is 75 lb/in. The coil must fit in a 2.1-in-dia hole with 0.1 in total clearance. Use 0.25-in diameter unpeened music wire and squared/ground ends. Use a 15% clash allowance, shear modulus G = 11.5 Mpsi, and weight density γ = 0.285 lb/in3. Assume Sys = 0.6Sut. Part A Find the shear stress at the initial deflection. Express your answer in pounds per square inch to three significant figures. τiτi = Part B Find the mean stress. Express your answer in pounds per square inch to three significant figures. Part C Find the alternating stress in the coil. Express your answer in pounds per square inch to three significant figures. Part D Find the fatigue safety factor for infinite life in shear. Express your answer using three significant figures.…An 18 coils helical spring having a load of 100kg. The modulus of elasticity in shear of spring is 96.62 GPa, OD of 9.256 cm and with wire diameter of 9.525 mm. The spring is squared and ground ends. Compute for the following respectively : 1) number of effective coils 2) spring index 3) axial load 4) deflection (mm)
- The inner spring of a compound helical spring is arranged within and concentric with the outer one and is shorter by 9 mm. The outer spring has 10 coils with a mean diameter of 24 mm and a wire diameter of 3 mm. (a) Determine the stiffness of the inner spring when an axial load of 162 N causes the outer spring to compress by 16 mm. If the radial clearance between the springs is 1.5 mm and the inner spring has 8 coils, find its wire diameter. (c) Disregarding the effect of curvature, find the maximum shear stress in each of the spring. Given G = 78 GPa.A spring with squared and ground ends is used for a load and deflection of 1.2 kN and 20 mm, respectively, with a spring index of 4. The wire diameter is 6 mm and the modulus of rigidity is 84 GPa. Which of the following is the active number of turns of the spring?A helical spring is made of 10 m diameter steel wire wound on a 100 mm diameter mandrel. If there are 10 active coils what is spring constant Take: C= 100 GPA What force must be applied to the spring to elongate it by 50 mm?