Practice ProblemA torque of 400 lb-ft is applied to the square section shown below.Determine the smallest permissible dimension a if the shearing stress islimited to 6000 psi. Neglect stress concentration in corners.t= 0.10 in.

Given,Torque applied to the square section, τ = 400 lb.ftshearing stress is, s = 6000 psithickness,…

Answered: t= 0.10 in. a

Science

Physics

t= 0.10 in. a

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter12: Fluid Dynamics And Its Biological And Medical Applications

Section: Chapter Questions

Problem 22CQ: Explain why the viscosity of a liquid decreases with temperature—that is, how might increased...

See similar textbooks

Similar questions

Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.12 ✕ 10−6 m3 is formed under a pressure of 5.50 GPa. Find the change in its volume (in m3) when it is released from the press and brought to atmospheric pressure. Take the diamond's bulk modulus to be B = 194 GPa. (Assume the system is at sea level.)
Explain why the viscosity of a liquid decreases with temperature—that is, how might increased temperature reduce the effects of cohesive forces in a liquid? Also explain why the viscosity of a gas increases with temperature—that is, how does increased gas temperature create more collisions between atoms and molecules?
Explain why the viscosity of a liquid decreases with temperature, that is, how might an increase in temperature reduce the effects of cohesive forces in a liquid? Also explain why the viscosity of a gas increases with temperature, that is, how does increased gas temperature create more collisions between atoms and molecules?
Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.00 106 m3 is formed under a pressure of 5.00 GPa. Find the change in its volume when it is released from the press and brought to atmospheric pressure. Take the diamonds bulk modulus to be B = 194 GPa.
Why are gases easier to compress than liquids and solids?
Hoover Dam on the Colorado River is the highest dam in the United States at 221 m, with an output of 1300 MW. The dam generates electricity with water taken from a depth of 150 m and an average flow rate of 650 m3/s. (a) Calculate the power in this flow. (b) What is the ratio of this power to the facility's average of 680 MW?
A short, square timber post supports a load of 115 kips. If the allowable unit compressive stress is 1000 psi, what nominal size square timber should be used.
The power P of a jet of water is jointly proportional to the cross-sectional area A of the jet and to the cube of the velocity v. (a) Write an equation that expresses this variation. (Use k for the constant of proportionality.) P=Akv^3 (b) If the velocity is doubled and the cross-sectional area is halved, by what factor is the power changed?(c) If the velocity is halved and the cross-sectional area is tripled, by what factor is the power changed?
Determine the minimum shear stress within the fluid. Express your answer using three significant figures and include the appropriate units.
You are provided with a metal block having dimensions of 124mm x 100mm x 45mm.Explain how you should place the block on the surface of a floor so that minimumpressure will be exerted by the block on the floor. Calculate the minimum pressure if themass of the block is 10kg.
Currently eighty-five percent of all neck injuries are caused by rear-end car collisions. To alleviate this problem, an automobile seat restraint has been developed that provides additional pressure contact with the cranium.During dynamic tests the distribution of load on the cranium has been plotted and shown to be parabolic. Determine the equivalent resultant force and its location, measured from point A.
You inflate the tires of your car to a gauge pressure of 38.0 lb/in2. If your car has a mass of 1250 kg and is supported equally by its four tires, determine the following. (a) Contact area between each tire and the road m2(b) Will the contact area increase, decrease, or stay the same when the gauge pressure is decreased? (c) Gauge pressure required to give each tire a contact area of 117 cm2 lb/in