-(t) + e(t) b) A closed-loop data system is shown below. The sample data is 10Hz A/D Le(k)_ f=10 Hz K(Z) ]..[ D/A G₁(S) y(t) The following equations represent the digital controller and the continuous time plant respectively: b) What are K(z) and Gp(s)? c) The D/A converter is ZOH. What is the closed-loop transfer function M(Z)=Y(Z)/R(Z) Of the equivalent discrete time system

-(t) + e(t) b) A closed-loop data system is shown below. The sample data is 10Hz A/D Le(k)_ f=10 Hz K(Z) ]..[ D/A G₁(S) y(t) The following equations represent the digital controller and the continuous time plant respectively: b) What are K(z) and Gp(s)? c) The D/A converter is ZOH. What is the closed-loop transfer function M(Z)=Y(Z)/R(Z) Of the equivalent discrete time system

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

Derive the expression of the equivalent circuit. (R1;=5 kΩ ,R2=10 ΚΩ, rπ, =10 kΩ)
Find the solution to the difference equation given below?[?] − 0.25?[? − 2] = ?[?]when the unit-step function ?[?] = ?[?] is applied to this system assuming the initial conditions of ?[−1] = 1 and?[−2] = 0.
A discrete time signal x[n]= {4,4,0,2} is applied to a 4-bit microprocessor to compute the frequency domain sequence which is periodic and discrete in nature. Assume the microprocessor computes the frequency coefficients in a fast and efficient manner than the conventional method.
A new model of electric vehicle contains two essential electronic components. Ifeither one of the components fails, the vehicle will not function.Let A and B denote the lifetimes (in years) of the two components. Assume that A ∼ Exp( 1, 20 ), that B ∼ Exp( 1, 25 ), and that A and B are independent of each other.1(a) Let C denote the time when the electric vehicle becomes inoperable due to one of thecomponents failing. Find the pdf of C.Hint: start by finding the cdf of C.(b) What is E[C]?Hint: the pdf you obtain in part (a) should be of a familiar type
Calculate the range of values K will take for the steady-state error to be ??? ≤ 0.04 when the input of the system is ?(?) = ?. Calculate the range of values K will take for the damping ratio to be 1>ξ ≥(1/2√6). Calculate the damping rate ξ and the undamped natural frequency ?? so that ? = 0.5
Use the Karnaugh Map (POS Expression) to reduce the logical expression:F (A, B, C, D) = (0, 1, 6, 12, 13, 14) d) Labelled and verify diagram with their pin configuration & generated equation e) Observation table of the circuit diagram f) Expected output using the generated equation g) Verify your Expected results with the simulation results.
Input output relationship of a continuous time linear time invariant system is representedby a differential equation given as?2?(?)??2 − 4?(?) = ?(?)where ?(?) denotes the input while the output is denoted by ?(?). The initial conditions are given as ?(0) = 3and ??(?)??|?=0 = 2. Find the output of this system when ?(?) = sin(2?) is applied as an input.
Find the state and output equations of the system given by the unit step function response (?) = ? + 2 /? (?2 + 8? + 25).
a) Y(ω) = 1/(5+jω) The expression above defines the frequency domain signal Y(ω) from a time domain signal y(t) i) Determine the imaginary & real parts of Y(ω). ii.Determine the signal y(t) that produced the signal Y(ω). b)What are the 3 areas of application of i.Signals ii.Systems c) Briefly summarise with explanation the difference between discrete & continuous time signal and also write an expression that describes each signal type.
Write the differential equation that is mathematically equivalent to the block diagram shown. Assume that r(t) = 3t^4
1. Consider the discrete-time system which has input of signal x[n] and output ofy[n] = n^2 x[n].Is this system a) linear, b) time-invariant, c) memoryless, d) causal, e) stable?Explain your answers.
Given a discrete-time linear time invariant system with input x[n] and output y[n] being related by y[n + 2] - 0.6y[n + 1] - 0.16y[n] = 5x[n + 2] the input x[n] = 0.4 ^ n * u[n] and the initial conditions are y[- 1] = 10, y[- 2] = 0 The zero state response is yzs [n] = [c1 (−0.2)" + c₂ (0.8)" + c3(0.4)"]u[n]. We have C₁ =, C2=, C3= ?