t it is tha

Q: ue of specifie 7.0 cal/mole

A:

Q: you s < showing how you de

A:

Q: 10- The hook law is

A: To explain: The Hook's law. Explanation: If the force is applied to the material, then the material…

Q: d the answe

A: Convection Convection consists of 2 mechanisms Energy transfer due to random molecular motion…

Q: over it vity of oi

A:

Q: how much wilu he need to invert

A: Given: A=3220000 R=1.85% n=2 t=5 To determine: Principal amount

Q: draulic pre eter and plun

A:

Q: S teath oulat

A:

Q: MPa . Assumin H/m² and Poisso hange in diamet

A: Given data  Dia of pressure vessel =650 mm Internal pressure = 14.7 Modulus of elasticity = 200 GPa…

Q: s Tafel p

A: introduction: here we have to explain tafel pot.

Q: Ratio of the temperature?

A: Given; Total emmisive power of a surface is; ∈1=500 W/m2At a given temperature=T1∈1=1200 W/m2At a…

Q: the amoun

A:

Q: Calculate dy for dt Int=r'in(y+e')

A:

Q: Q Heat t reatments and theireFfects2

A: Concept: Heat Treatment Methods are In this methods, the steels materials are heated to upper…

Q: I o2s+lo4 s+1. .96 2. L'st ++T?

A:

Q: Len figur employ ing that h air ar

A: introduction we have to find out efficiency and specific heat are same for air and gas.

Q: дл др Os ӘТ S Cp

A: Write the expression at constant enthalpy. dh=Tds+vdP0=Tds+vdP∂s∂ph=-vT

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: euguA 80hN GUKN 30 SOKN TERnd a ond f

A:

Q: ocal hea

A: Local heat transfer coefficient will be at the particular on heat transfer surface it is equal to…

Q: The term k/pc_p is the

A: option D is correct ...that is a,d

Q: question 3 above is c hat is the final tem v of the steam in this

A: Given data P1 = 2800 kPa P2 = 4700 kPa T = 390 degree C Specific enthlpy, specific volume and…

Q: M B. a) T 09 4 3. A

A: Given Data⇒ Figure

Q: about the y a

A:

Q: Iflow rat

A:

Q: S were taken bservations n

A:

Q: e is pl= Eransfe

A: Diameter of the rod (tube) d = 50 mm Ts = 383 K   T∞ = 373 K Properties of water at 100∘C ( 373 K)…

Q: D raio s.f.D and B.M.

A:

Q: aruness, it piece ( .ASTM) from Table 24-A

A: Given data In this problem unit conversion and material property of various material was required in…

Q: if Re 77 Soo %3D 등 = \ , * 103 Determine f %3D from mod'] chart.

A:

Q: Find a) Сp, Cv

A:

Q: Problem A.2. Calcu

A:

Q: ut of tha

A:

Q: at the d to be Ssumins

A:

Q: Wh at are, the re as shown in the JO

A:

Q: s ans soon ty

A: Given Data : Initial length of of iron piece(L)=108 mm Stressσ=786 MPa Deformation is entirely…

Q: ure B A <1 of 1

A: Introduction: Velocity is defined as the rate of change of an object's location with regard to a…

Q: A temperature so T= a In 0.!

A:

Q: Its coeffi

A:

Q: 1 1. FIMD RXAS AT A D 2. ou Pids oF POLLETS Bx By C- C. C. ALE OF RESUTAT AT B,C &A

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: S" sin?t cos*t dt

A: None of the choices

Q: ss is 8 1.

A: given mass m=80kg

Q: ains a he potential difference (in V) ad

A: Determine the potential difference.

Q: Isteel rule be

A: detailed Solution given below. leave positive feedback if it helps.

Q: non whe

A: Angular acceleration,  α = 27 θ Since,α = dωdt              = dωdt dθdt               = ωdωdθ where…

Q: ter at the d

A: Given : Diameter of jet = 2 cm = 0.02 m Area = a= πa4 Velocity = 25 m/s θ = inclination at outlet=…

Q: What is the temperature of the cylinder whe

A: Need To calculate the temperature of cylinder.

Q: the regritade ef the

A:

Q: • What is: d cos(at +d), dt

A:

Q: 5. [vZ (cos + i sin) ( 6. 3-2i

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.