(b)In Figure Q5, the 17 kg of circular disk is originally rotating with a clockwise angularvelocity, o = 49 rad/s at the end of the link BC. Given the kinetic coefficient offriction, uk = 0.25 when the disk is then placed against the wall.(i)Draw the kinetic diagram of all forces exerted on the circular disk.(ii)Calculate the force of link BC.(iii)Calculate the angular acceleration of the circular disk.(iv)Calculate the time required to stop the motion of the circular disk, B150 mm60°Figure Q5

mass (m) = 17 kg angular velocity (w) = 49 rad/sec kinetic friction (μ) = 0.25∑ FX = FB cos 60 -…

t the end of the link BC. Given the kinetic coefficie he disk is then placed against the wall. liagram of all forces exerted on the circular disk. e of link BC. alar acceleration of the circular disk.

t the end of the link BC. Given the kinetic coefficie he disk is then placed against the wall. liagram of all forces exerted on the circular disk. e of link BC. alar acceleration of the circular disk.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single cylinder reciprocating engine has speeded 300 RPM. Stroke 250 mm, mass of reciprocating parts 50 kg. Mass of revolving parts at 150 mm radius 37 kg. If two fourth of the reciprocating parts and all the revolving parts are to be balanced, find (i) The balance mass required at 400 mm radius (ii) The residual unbalanced force when the crank has rotated 45° TDC.
A uniform, solid cylinder of mass mc=7.42 kg and radius R=.26 m with Icm=1/2MR^2 is attached at its axle to a string. The string is wrapped around a small ideal pulley and is attached to a hanging block of mass mb=2.73 kg as indicated in the figure above. You release the objects from rest and the cylinder rolls without slipping. What is the magnitude of the acceleration of the block?
A turntable is a uniform disc of mass 2 kg and radius 1.3 x 10-1 m. The turntable is spinning at a constant rate of = 0.5 . The motor is turned off and the turntable slows to a stop in 8.0 s with constant angular deceleration. Find the (a) moment of inertia of the turntable; (b) initial rotational kinetic energy; (c) angular deceleration of the turntable while it is slowing down; (d) total angle in radians that the turntable spins while slowing down; and (e) magnitude of the frictional torque.
A box of mass m = 0.7 kg is attached to a rope which is wrapped around a physical pulley with a radius of R = 10.2 cm and a rotational inertia of I = 0.075 kg·m2. When the box is released it starts to fall down with a constant acceleration and, at the same time, the pulley starts to spin up, see the picture below. Assuming that the pulley is frictionless, what is the magnitude of the box's acceleration and what is the tension in the rope? The acceleration of the box, a ? The tension in the rope, T? If the box starts from rest and traveled downwards a distance of h = 28 cm, what is the speed of the box and what is the angular velocity of the pulley? The speed of the box, v =? The angular velocity of the pulley, ω? -------------------------------------------------------------- A Merry Go Round carousel has a radius of R = 2.4 m and a rotational inertia of I = 695 kg·m2. A 75‑kg student is on the carousel at the midpoint between the carousel's center and the rim (at R/2 distance from…
The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of 0.29 mm and 0.43 mm, respectively. The total mass of the pulley system is 14 kg and its turning radius is 0.26 mm from its center. The mass of block A is 9 kg and the mass of block B is 2 kg. If the coefficient of kinetic friction between block B and the floor is 0.2, find the angular acceleration of the pulley.
A wheel of mass m, radius r and radius of gyration k is rolling along a horizontal road with hub velocity v in the +ve x direction. Brakes are applied to the wheel, providing a torque of -M, slowing the vehicle to rest. Assuming that the wheel rolls without slipping and the hub position starts at x=0, where m = 10 kg, r = 0.85 m, k = 0.595 m, v = 5m/s, M = 21 Nm, g = 9.81 m/s^2 a) Find the constant acceleration, (ax) of the wheel hub b) Find the minimum static coefficient of friction (mu) between the road and the wheel c) Find the stopping distance (smax) and time (tmax)
An electric motor is accelerating a 250 kg load with acceleration of 1.2 m/s? througha gear box as shown Figure Q1(b). The rope that carries the load and spiral spring are encircled on a pulley with diameter 1.2m. Gear box ratio is 0. 1 and gear box efficiency is 100%, while gear box equivalent moment inertia is 5.55 km?. Neglect friction effect in this drive system and assume spiral spring force is X newtonCalculate the torque of the motor needed to bring up the load with acceleration1.2 m/s?.
An elongated rod of mass 4-kg has a mass of 2-kg at point A to a block moving vertically, 4-kg at point B pinned to a massive disk. The disc rotates without rolling, It is assumed that the block also moves in a frictionless channel. Please pay. The mechanism is released when stationary at θ=60º. Find the angular velocity of the rod when θ=0º.
a 4.8 kg block is resting at the top of a 30 degree slope of height 1 m it is attached to a cylindrical pulley of mass 1.7 kg and radius 8 cm by a massless string that unwind as the block slides down hill if the acceleration of the block is 1.9 m per second squared what is its normal force find the velocity at the bottom of the slope using forces and torques
A truck of mass 15000 kg traveling at 1.6m/sec impacts with a buffer spring, which compresses 1.25mm per kN. Find the maximum compression of the spring. ( No shortcut please)
Figure Q3(b) shows a uniform bar AB of mass = 8 kg hinged at point C. Point A is connected to a spring to maintain the bar in vertical direction, and the stiffness k = 500 N/m. If point A is displaced counter-clockwise by a small angle θ = 3.5 degree and released, (i) With the free body diagram and kinetic diagram, determine the initial horizontal displacement of A.
A disk is attached by a spring to a pin. The disk can roll in the horizontal direction and the pin is above it. The spring has an unstretched length of .5m and a spring modulus of 600 N/m THe disk has a mass of 20kg and a radius of 200mm The center of hte disk is 600mm below the pin and 320mm to the side (so the spring starts diagonal) If the spring is released, what is the speed of the disk when the spring is perfectly vertical? Assume the disk does not slip and is free to spin