Task 2. Permeability testTable 2 General information and results of constant head permeability testSpecimen diameter (cm)Specimen length (cm)Temperature (°C)Head loss (cm)5.868.2321.505.0TrialTemperatureFlow volume (cm³)Time (sec)125592025582032556204255520Table 2 shows the general information and results of constant head permeability test.(1) Describe the test procedure of constant head permeability test.(2) Determine the coefficient of permeability for each trial.

To find coefficient of permeability

Answered: Table 2 General information and results…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Why it is necessary for the water samples collected during site investigation be tested for chloride, sulphate ions and pH?
What are the two general types of hydrometers? What are their respective differences? Name and describe briefly at least five (5) specialized type of hydrometers. Why avoid air bubbles while pouring and mixing the sample? What may be on the fingerprints that may affect the accuracy of the result? What is the physical phenomena that affects the reading of the hydrometer scales?
Sample 2: Mass with empty mold M1 Mass of soil and mold M2 Hydraulic Head h Time interval t Volume V 145 g 250 g 950 mm 0.34 min 0.0046 L 145 g 260 g 900 mm 0.33 min 0.0049 L 145 g 228 g 922 mm 0.30 min 0.0051 L 145 g 281 g 915 mm 0.29 min 0.0044 L 145 g 219 g 908 mm 0.39 min 0.0042 L The diameter of the mold = 2.5 cm, Length of the sample = 0.3 m can u pls Find the permeability coefficient Mass of the soil Bulk Density Dry Density thank you Void Ratio
A constant-head permeability test is performed where the hydraulic gradient is 0.75. The crosssectional area of the sample is 0.25 ft2. The quantity of water flowing through the sample is measured to be 0.004 ft3/minute. (a) What is the coefficient of permeability in feet per minute? (b) What is the coefficient of permeability in millimeters per second?
Please answer all 1. List the three corrections which should be applied to the hydrometer readings. 2. Why is it important to remove the hydrometer from the measuring cylinder between readings? 3. A hydrometer test has the following results; Gs = 2.70, temperature = 240C, and L = 92 mm at 60 minutes after the start of sedimentation. Calculate the diameter of the smallest-size particles that have settled beyond the zone of measurement at that time (use the table in the lab manual to find, A=0.0128). D(mm) = A sqrt( L(cm) / t(min) )
A soil sample collect near the stadium has a volume of 0.05 m3 and a mass of 87.5 kg. Assume the water content is 15% and the specific gravity of solids (Gs) is 2.68. Draw a block diagram showing all the necessary mass and volume terms. Use the mass and volume values computed above to compute:
34 For a falling head permeability test, the following values are given: Length of specimen = 38.74 cm, Area of specimen = 19.58 cm^2, and k = 2.82 x 10^-3 cm/sec. What should be the area (in cm^2) of the standpipe for the head to drop from 64 cm to 30 cm in 8.6 minutes? Round off to three decimal places.
GEOTECHNICAL COMPLETE SOLUTION PLS For a falling-head permeability test, the following are given: length of specimen = 15.1 in., area of specimen = 3.9 in^2, and k = 0.0686 in./min. What should be the area in sq. in. of the standpipe for the head to drop from 25.1 to 12.6 in. in 8.9 min. ?
Please explain part 1 (ii) of the question given. 1) i) A 6 inch diameter well that fully penetrates a 40ft thick open aquifer is pumped at a rate of 100 gpm. The drawdown in the well is 22ft when a steady water level is established. The drawdown in a well 152ft distant is 12ft. Estimate the coefficient of permeabiliity of the soil deposit. Answer of permeability is K= 9.88 x10-4 ft/sec. ii) Discuss the validity of the answer obtained in 1( i ) and suggest how would you improve the test data obtained to produce a better value of k. Why?
A calibration test of a 12.7mm circular sharp edge orifice in the vertical side of a large tank showed a discharge of 589N of water in 81 sec. at a head of 4.73. Measurement of the jet showed that it traveled 2.35m horizontally while dropping 0.0305m. Compute the three orifice coefficients.
For a falling-head permeability test, the following are given:length of specimen = 380 mmarea of specimen = 6.5 cm2k = 0.175 cm/minWhat should be the area of the standpipe for the head to dropfrom 650 cm to 300 cm in 8 min?
For groundwater sampling in monitoring wells, what procedures for installing the well are necessary to ensure that the depth indicated for the water sample is accurate?

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS