TABLE 2 RESULTS OF ORI TEST Water Content (%) Weight (Kg) 14 1.45 16.5 1.71 18.5 1.87 20 1.88 21 1.76 22.5 1.67 If this test uses a sample mold with a size of 943 cm^3 , answer a few questions this: a. interpret the results of this proctor test, and determine the optimum moisture content and maximum dry density. (Gs = 2.7) b. Determine the range of moisture content for 90% compaction in the field c. Between soil A and soil B in Figure 1, which is easier to compact? Explain your answer.

TABLE 2 RESULTS OF ORI TEST Water Content (%) Weight (Kg) 14 1.45 16.5 1.71 18.5 1.87 20 1.88 21 1.76 22.5 1.67 If this test uses a sample mold with a size of 943 cm^3 , answer a few questions this: a. interpret the results of this proctor test, and determine the optimum moisture content and maximum dry density. (Gs = 2.7) b. Determine the range of moisture content for 90% compaction in the field c. Between soil A and soil B in Figure 1, which is easier to compact? Explain your answer.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter5: Soil Compaction

Section: Chapter Questions

Problem 5.17CTP

See similar textbooks

Similar questions

The result of the liquid limit tests where N is the no of blows and w is the water content in % are given as follows: Trial 1 N=11 w=53.9; Trial 2 N=15 w=50.6; Trial 3 N=23 w=48.1; Trial 4 N= 30 w= 46; Trial 5 N= 46 w=43.3; Trial 6 N= 53 w=41. The PL= 20 and the in situ moisture content is 45%. Determine the plasticity index. a.22 b.17 c.27 d.12
The result of the liquid limit tests where N is the no of blows and w is the water content in % are given as follows: Trial 1 N=11 w=53.9; Trial 2 N=15 w=50.6; Trial 3 N=23 w=48.1; Trial 4 N= 30 w= 46; Trial 5 N= 46 w=43.3; Trial 6 N= 53 w=41. The PL= 30 and the in situ moisture content is 35%. Determine the plasticity index. A. 27 b. 12 C. 17 d. 22
The data from a standard Proctor test are shown in the table below.a. Determine the maximum dry unit weight and the optimum water content.b. Plot the zero air voids line.c. Determine the degree of saturation at the maximum dry unit weight.Diameter of mold 101.4 mmHeight of mold 116.7 mmMass of mold 4196.50 gramsSpecific gravity, Gs 2.722
Problem 1:The results of a standard Proctor test are given in the following table. Given: Mold volume = 1/30 ft^3 and Gs = 2.69. Determine the void ratio and the degree of saturation at the optimum moisture content. Trial # Weight of moist soil in the mold (lb) Moisture content (%) 1 3.7 8.6 2 4.15 10.6 3 4.69 12.5 4 4.62 14.9 5 4.02 16.7 6 3.63 18.3 Problem 2The laboratory test in Problem 1 is used to develop field compaction specification for a highway project. A field unit weight determination during the construction revealed that the in situ moist unit weight is 124 lb/ft3 and the moisture content is 13.7%. Determine the relative compaction in the field.
Don't attempt wrong i will downvote.....A cylindrical soil sample, 7.3 cm in diameter and 16.8 cm in height, is tested in a constant-head permeability apparatus. A constant head of 75 cm is maintained during the test. After 1 minute of testing, a total of 945.7 gm of water was collected. The temperature was 20 oC. The void ratio of the soil was 0.43. Calculate the following: 1. The hydraulic gradient 2. The flow rate 3. The discharge velocity 4. The seepage force per unit volume 5. The coefficient of permeability
Afalling-head permeability test is performed on a fine-grained soil. The soil sample has a length of 120 mm and a cross-sectional area of 600 mm2. The water in the standpipe flowing into the soil is 0.60 m above the top of the sample at the start of the test. It falls 50 mm in 30 minutes. The standpipe has a cross-sectional area of 200 mm2. (a) Make a sketch of the described conditions. (b) What is the coefficient of permeability in millimeters per second? (c) What is the coefficient of permeability in feet per minute? (d) On the basis of the calculated value for khyd, what is the probable soil type?
During a falling head test, the head fell from 80cm to 65cm in 83 seconds. The specimen was 5cm in diameter and had a length of 100mm. the diameter of the standpipe was 0.80 cm. Temperature during the test is 90deg. C. a.) Compute the coefficient of permeability of the soil at 20deg. C _____cm/min b.) Compute Seepage velocity if the void ratio is 0.90 _____cm/min c.) Determine the Rate of flow _____cm/min
A modified Proctor compaction test was carried out using a cylindrical moldwith a 1000 ml volume. Table 2 summarizes the results. a. Plot the compaction and ZAV curves (RD=2.75 and ρwater=1000 kg/m3)b. Determine the maximum dry density and the optimum moisture content Table 2 Moisture Content (%)Mass of WetSample (g)10.5 2033.211.8 2146.613.0 2203.514.9 2183.116.4 2147.617.6 2116.8
The results of a standard Proctor test are given in the following table. Determine the maximum dry density (kg/m3) of compaction and the optimum moisture content. Volume of Proctor mold (cm3) Mass of wet soil in the mold (kg) Moisture content (%) 943.3 943.3 943.3 943.3 943.3 943.3 943.3 943.3 1.6 1.71 1.77 1.83 1.86 1.88 1.87 1.85 9.9 10.6 12.1 13.8 15.1 17.4 19.4 21.2
From the constant head permeability test arrangement shown, the following values are given: Void ratio of specimen = 0.46 Length of Soil Sample = 450mm Constant head difference = 700mm Water collected in a period of 3 min = 0.000354 m3 Cross-sectional Area of Soil Sample = 0.00226 m2 Determine the coefficient permeability in m/hour (Ans: 2.102 m/hr) Compute the discharge of velocity in m/min. (Ans: 0.052 m/min) Compute the seepage velocity in m/min. (Ans: 0.165 m/min)
In falling head permeability test the initial head was 350 mm and the final head was 50 mm. The cross-sectional area of the burette was 200 mm2. The sample was 50 mm in diameter and 100 mm long. If the test took 8 hours and 45 minutes, what was the coefficient of permeability of the soil in m/s? a.7.15 x 10-7 m/s b.6.29 x 10-7 m/s c.7.89 x 10-7 m/s d.8.78 x 10-7 m/s e.5.69 x 10-7 m/s
A cylindrical soil sample 50 mm in diameter and 200 mm in height is used as thepermeameter in a falling head permeability test setup. In one minute of observation, thehydraulic head in the 10 mm diameter standpipe through which test water went reducedfrom 900mm to 500 mm. During that time, 1.5 liters of water were collected in the graduate. Calculate the soil sample's permeability coefficient in cm/s.