Table Q2 show the working pressure inside an engine which moves the piston at different positions inside the engine cylinder. Determine the total work done during the piston movement, 15 inches inside the cylinder. The piston head diameter was measure to be 8 inches. Given that the total work done relation is ; -15 Work = A p (x)dx , where A is the area of the piston. Table Q2 Item Piston head Piston Pressure position from top center of the engine cylinder (у), ст (p), psi 1 110 1 130 3 140 4 2.5 170 4 185 210 7 7 215 8 8 185 9 11 135 10 12 100 11 13 90 12 14 70 13 15 40

Table Q2 show the working pressure inside an engine which moves the piston at different positions inside the engine cylinder. Determine the total work done during the piston movement, 15 inches inside the cylinder. The piston head diameter was measure to be 8 inches. Given that the total work done relation is ; -15 Work = A p (x)dx , where A is the area of the piston. Table Q2 Item Piston head Piston Pressure position from top center of the engine cylinder (у), ст (p), psi 1 110 1 130 3 140 4 2.5 170 4 185 210 7 7 215 8 8 185 9 11 135 10 12 100 11 13 90 12 14 70 13 15 40

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Suppose a very tall open cylindrical container having 1.5 m diameter and is filled with 2226.6 liters of water is rotated about its central axis at constant angular velocity. Determine the height h in meters at the condition where the pressure at point B located at the bottom, 0.6m radial distance from the center becomes 16 kPag. Use g = 9.81 m/s2 and density of water = 1000 kg/m3
The round handle of a faucet is affixed to a shaft that lets a valve to be open and closed every time the round handle is rotated. Give the radius of the handle if the shaft has a diameter of 1 cm and the MA of the machine is 8.
A cylindrical water tank has a height of 8 m and a radius of 2 m. Suppose the water tank is half full of water. Determine the work required to empty the tank by pumping the water to a level 2 m above the top of the tank. Leave the answer in terms of p, g, and pi if necessary.
Q6: A hydraulic lift is to be used to lift a 2500 kg weight by putting a weight of 25 kg on a piston with a diameter of 10 cm. Determine the diameter of the piston on which the weight is to be placed.
Given the barometric pressure of 14.696 psia ( 29.92 in. Hg as. ), Make these conversion: c. 24.5 psia to psi vacuum and to Pa, Ans. 9.804 psi vac; – 67598.6 Pa d. 14.5 in. Hg gage to psia, to Torrs, to Pa Ans. 21.81 psia; 368.316 Torrs(Ans. 49088.95 Pa )
A tank of water 4 m deep receives a constant upwardacceleration a z . Determine ( a ) the gage pressure at the tankbottom if a z = 5 m 2 /s and ( b ) the value of a z that causes thegage pressure at the tank bottom to be 1 atm.
A compressor takes in refrigerant at a pressure of 80.34 psia. The dischargepressure of the refrigerant is 281.74 psia. What is the compression ratio ofthe compressor? Round the answer to the nearer tenth.
A 98.43ft vertical column of fluid (density is 1878 kg/m3) is located where is 31.66ft/sec2. determine the pressure at the base of the column in kPa.
Two pipes A & B carries an oil of specific gravities 0.9 & 1.2 respectively. A U tubedifferential manometer is connected between the pipes. The center of the pipe A is 1 mabove the pipe B. The height of oil in right limb is 30 cm. Also, the mercury leveldifference is found in right limb as 10 cm. Find the pressure difference between these twopipes in kPa. Sketch the arrangement neatly.
Determine the gage reading P in psi. SG of Hg is 13.57. Show your work
An unknown gas is flowing through a venturi meter whose diametersas shown. Gage pressures are measured 12.2 psia at the entranceand 11.8 psia at the throat. Take the density to be 0.105 lb/ft3.Determine the following: A) Neglecting friction, the volume flow rate of airB) If the pressure gauge is replaced with a manometer withmercury as its medium (SG=13.6), what will be the height ofthe mercury in inches? Draw the most possible orientationof the manometer and its fluid height.
Predict the changes of the differential height in the manometer if afluid with the density lower than water is used as the working fluid.