tank is in the shape of an inverted cone, having height h = 2.5 m and base radius r = 0.75 m. If water is poured into the tank at a rate of 15 L/s, how long will it take to fill the tank? Water flows into a cubical tank at a rate of 15 L/s. If the top surface of the water in the tank is rising by 1.5 cm every second, what is the length of each side of the tank?

tank is in the shape of an inverted cone, having height h = 2.5 m and base radius r = 0.75 m. If water is poured into the tank at a rate of 15 L/s, how long will it take to fill the tank? Water flows into a cubical tank at a rate of 15 L/s. If the top surface of the water in the tank is rising by 1.5 cm every second, what is the length of each side of the tank?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water enters a large rigid tank steadily at a rate of V . = 0.5 m3/s, and exits through a large rectangular opening through which the velocity changes linearly in the vertical direction from 4 m/s to 5 m/s. Knowing that the tank is full, determine the magnitude of the velocity through the circular opening at the top whose diameter is D = 15 cm.
There are two liquid tanks A and B connected to each other by a tube as shown in the figure.The base of A is 75 cm2 and the base of B is 30 cm2. The density of the oil is 0.8. How many kilograms of oil must be put in tank B so that the level difference between the water in the two branches is 15 cm? Which point supports more pressure, C or C'?
A right circular cylindrical container 3m in diameter and 4 m high is ½ full of water. When rotated about its vertical axis at the rate of 5 radians per second, what is the volume of the paraboloid formed by the rotation of the vessel? Unit of the Correct Answer: m^3 An open cylindrical tank one meter in diameter and 3 m high is 3/5 full of water. If the tank is rotated about its vertical axis, what speed should it have in rpm so that the water could just reach the rim of the tank. Unit of the Correct Answer: rpm
Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an area of Ap= 0,8 cm? and A= 0.04 m2, Hydraulic oil with a specific gravity of 0.870 is pumped in as the small piston on the left side is pushed up and down, slowly raising the larger piston on the right side. A car that weighs 13,000 N is to be jacked up. At the beginning, when both pistons are at the same elevation (h= 0), calculate the force F+ in newtons required to hold the weight of the car. 1. What height of mercury column will cause a pressure of 680 kPa? Use sg of mercury equals to 13.6 2. Determine the pressure in a vessel of mercury, specific gravity 13.6, at a point 20 cm below the surface. Express the answer in kN/m2.
A pontoon, 4 m long x 4 m wide x 2 m deep, floats in fresh water with a draft of 1.50m. Compute the time for the pontoon to sink to its top edge, after opening a standard orifice 15 cm in diameter (C=0.60) located at its bottom. a.139 seconds b.215 seconds c.235 seconds d.125 seconds
An open cylindrical tank having a radius of 0.34 m. Is filled with water at a depth of 0.84 m. If it is rotated about its vertical axis to a velocity of 110 rpm, what should be the height in meters so that no water will be spilled out
Calculate the pressure and speed of water at points b and c as shown.
Shown in the figure below is a small decorative wheel fitted with flat paddles so the wheel turns about its axis when acted upon by a blown stream of air. Assuming that all the air in a 15-mm-diameter stream moving at 0.35 m/s strikes one paddle and is deflected by it at right angles, compute the force exerted on the wheel initially when it is stationary. The air has a density of 1.20 kg/m3 . The paddle is on a horizontal plane.
An open cylindrical tank 2 meters in diameter and 4 meters tall is half – full of water. The tank is rotated about its vertical axis at constant angular speed. How much water is spilled (in liters) if the angular speed is 90 rpm?
A rectangular tank that is 5/6 full, has a length of 26cm, height of 20cm and width of 15cm. If the water is transferred to another tank that is 18cm by 9cm by 30cm, how much water will overflow? (1cm^3 =1mL)
Water flows into a cylindrical tank at the rate of 20 cu.m per sec. How fast is the water surface rising in the tank if the radius of the tank is 2m.
As shown in the figure, water enters and exits a U-shaped piece of pipe located in the horizontal plane. (1) the total absolute pressure in flange number is 200 kPa and there is a mass flow rate input of 40 kg/sec into the pipe. In flange (2), the total pressure is 150 kPa and there is a mass flow rate output of 30 kg/sec from the pipe. 4 kg/sec from section (3) and 6 kg/s from section (4) are discharged into the atmosphere at a pressure of 100 kPa. By working with relative pressures; Determine the total Rx and Ry forces on the two flanges connected to the pipe. (Answer: Rx = 1545,7 N (←) and Ry = 91,96 N (↑))Note:-Mass flow rate = Specific mass x Flow rate. -Specific mass of water : ?w=1000 ??/?3-A flange is a construction element that is usually produced as a standard for the sealed joining of two machine or installation elements.-The sections (1) and (2) are close enough to each other.-The momentum flow correction coefficient for the fluid entering and exiting the control volume is…