Task 8 - HIGH RISE BUILDINGS Steps on how to build a high rise buildings. (From rawland) Send a copy to me.

Q: answer all parts

A:

Q: ****************** Draw a flowchart to find the sum for the following numbers: Sum= 6 + 10+ 14 + 0

A:

Q: Define Peclet number.

A: It is defined as the ratio of the rate of advection of a physical quantity by the flow to the rate…

Q: HELLO PLEASE HELP, WITH COMPLETE SOLUTION. PLEASE DO NOT MAKE IT COMPLICATED THANK YOUU! 4 DECIMAL…

A:

Q: missing value

A:

Q: год I KLF Мmax = Am max=

A:

Q: What is the volume of this room in cubic feet?

A: Knowing the volume of a room is important when determining its heating and air conditioning needs.…

Q: where did you get 6?

A: 6 is the loading intensity at B.

Q: This blueprint shows the layout for rectangular ducting for a home forced airheating system. The…

A: As per out rules and guidelines we solve only first three subparts kindly resubmit the remaining…

Q: Please show your complete solution for upvote. Please typewritten. Thank you!

A:

Q: (C): Find representative Fraction scale (R.F) from verbal statement of (6 inch to 1 mile) (12mile to…

A:

Q: - Calculate total BOD,

A:

Q: express each measurement in feet.42 inches

A: Given: The measurement is 42 in.

Q: A contractor is to construct a tank to contain water for his construction project, given that the…

A: The given values are as follow, The height of the tank (h) = 2.40m The diameter of the tank (d) =…

Q: Size of photograph

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: Answer is letter B

A: Given data- Diameter(D) = 8in Height (H) = 16in Youngs modulus (E) = 2.5× 10^6 lb/in² Unit…

Q: Complete the table below.

A:

Q: Refer to the figure. bw

A: (a) using 28mm diameter main reinforcement bars, determine    the nominal ultimate moment capacity…

Q: Choose the correct one and explain it

A: Given data : Normal stress in X direction (σX)=5 MPaNormal stress in Y direction (σX)=5 MPaMajor…

Q: express each measurement in feet.50 inches

A: Given: The measurement is 50 in.

Q: You are trying to plot a drawing using the 1:100 scale, but the drawing will not fit to the plot…

A: The ratio of distance on map to its distance on ground is known as scale. y

Q: This assignment consists of determining the quantities for a cost estimate in different units.…

A: from the given data from the problem Type  Length height Area After completion of deduction…

Q: (a) With a neat sketch write short notes on mechanically operated trucks to move material from one…

A: Solution: a.  The Mechanically operated trucks that are used to carry material from one location to…

Q: What sieve size has the lowest percent passing? (2 decimal places, no need for unit) Blank 1 Blank 1…

A:

Q: Solve for this please. Thank you!

A: As there are two questions posted, according to guidelines only the first is being answered. Kindly…

Q: Figure 20-7 Questions 1-10. 44 8. 6 38 20 24 34 Ol 76 8 80 84 88 92 10 Match the dimensions…

A:

Q: Solve ONLY LETTER D and E. The first three subparts are already answered in my previous question…

A:

Q: Please include complete solution and diagram if possible.

A:

Q: 1. What thickness limit classifies metal as being sheet? 2 What is the decimal size of 14 AWG sheet?…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Calculate the total area required for placing the quarry tiles on the internal walls in this…

A: There are two short walls and two long walls, And there is a deduction in area in the place of the…

Q: You are to construct a Bodega with a rectangular floor plan using CHB (Concrete Hollow Blocks) as a…

A:

Q: 2. Draw the Gant chart for the following activities: Activities Start Duration Drywall April 1st…

A: A Gantt chart, commonly used in project management, is one of the most popular and useful ways of…

Q: Directions: You are an architect in a constructiorn company. You are tasked to build 3 circular…

A: As mention above the the diameter and length of three circular tank are or we can say that capacity…

Q: Fill up tabele#1 below to calculate exact quantity of cach given item as given in figure#1 & #2…

A: Calculate the total centerline length L as given as, L=4.3-0.125+6.5-0.125+5=15.55 m 1) Item…

Q: As described in the Data and Results part of , all tables and graphs must have descriptive…

A: →The relation between a spring force and its deflection:- Deflection X (mm) Spring Force F(N) 0…

Q: Answer 9-4,Convert from english to metric units and draw FBD. Show your step by step answer with…

A: Let the angle of truss =θ=tan-121.5=53.130 Now let us remove the external load at A and replace the…

Q: Provide the correct points, draw the figure below using Absolute, Relative and Polar coordinate…

A: Given figure ,

Q: Using table Draw S.f.D &B.M.D as shown 20kN RR, 20 'Rz

A: It is required to draw the SFD and BMD

Q: Write the selection criteria for a good paints

A: Paint:- Paints are applied on the external surface of a structure or a metal to act as a protective…

Q: Subparts: a, b, & c. Please write it on paper.

A:

Q: c)Components of Canal headworks. Subject: Irrigation Engineering

A: Any hydraulic structure which supplies water to the off taking canal is termed as canal headworks.

Q: How to get TEC and TBC

A: Given data  0.77TEC + 0.8TBD = 1440...........(1) 0.514TEC - 1.6 TBD = 0...............(2)

Q: 20 20 20 40 2. 3. +.

A: Given data  Cross sectional view To find Size of the column

Q: A contractor is to place tiles for a living room with a floor area of 8 meters x 6 meters. If each…

A: Total floor area, A=8 x 6=48m2 tiles dimension, a= 0.4 x 0.4=0.16m2

Q: (a) With a neat sketch write short notes on material handling equipment that is fitted to cranes…

A: a. Some of the important container cargo handling equipments are: Base Twistlock: It is used on deck…

Q: 1. Create the following drawing in AutoCAD, export and submit it as a PDF on Canvas. 5.0 1.5 01.5 55…

A: Solution:- Dear student, your drawing is ready but not uploaded in pdf format because that option is…

Q: express each measurement in feet.60 inches

A: