15) Please include complete solution and diagram if possible. A line was determined to be 2,395.25 m whenmeasured with a 30-m steel tape supportedthroughout its length under a pull of 4 kg at a meantemperature of 35°C. Tape used is of standardlength at 20°C under a pull of 5 kg. Cross-sectionalarea of the tape is 0.03 cm^2. The coefficient ofthermal expansion is 0.0000116/°C and themodulus of elasticity of the tape is 2 millionkg/cm^2. Find the corrected length (in m) of theline?

Answered: Image /qna-images/answer/ac2d8825-e0e2-452b-840e-a2b43e157bd1.jpg

Answered: Please include complete solution and…

Engineering

Civil Engineering

Please include complete solution and diagram if possible.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: What is an earth dam. Draw and label an earth dam. Explain the function of the various components of…

Q: Define The required diameter

A: A diameter is a chord that runs through centre point of circle. The centre of circle is at midpoint…

Q: Show free body diagram and complete solution. Thank you

Q: Give details of JPCP, JRCP, and CRCP with necessary figures.

A: In pavement construction, three different concrete pavement design types are commonly used: Jointed…

Q: The areas in cut of two irregular sections 45 m apart are 44 m^2 and 66 m^2 respectively. The base…

A: Given values: Area of 1st cut, A1 = 44 m2 Area of 2nd cut, A2 = 66 m2 Distance between the cuts, L =…

Q: Define vibration

A: Vibration has been defined in the following step.

Q: 2. Complete the profile level notes shown below, perform the customary arithmetic check, provide a…

A: Solution: The table is below:

Q: Define Lateral Capacity

A: Lateral capacity:

Q: derivation of the formulas used in every section

A: This question has been taken from fluid mechanics

Q: What is the groundwater table?

A: Ground water table:

Q: What is bulk density? own word plss type written

A: Bulk density is the ratio of total mass of soil to the total volume of soil mass.

Q: Line standard End standard How will you determine if the measurement methods described above is a…

A: Line Standard: Measurement of the distance between two lines is known as Line standard. For wide…

Q: Please show the complete detailed solution. W=53

Q: 1) Determine the area of the shape below. -130.0- 100.0 -160.0-

A: The above figure is the trapezoid The area of the trapezoid = sum of the parallel…

Q: Explain the Plan representation of components and locations for concrete and earth fill dam.

A: Earthfill Dam: Bottom Width: The dam 's highest width or crest size will be adequate to stand up to…

Q: please indicate detailed solution.

Q: ind the question Classify A and B, thank.

Q: how full solution

Q: M1 Apply the terminology used in construction technology to a given building construction project.

A: Brief Concept Introduction- Concrete Technology- Concrete technology is concerned with the study of…

Q: What is Soil stabilization?

A: Soil stabilization is a method of mixing and blending certain materials to improve the properties of…

Q: PLETE DIAGRAMS Use 3 decimals

Q: Which shape has more sides than a quadrilateral?

A: A polygon is a two-dimensional shape that is formed by a set of line segments forming an enclosed…

Q: Give me right solution with clear calculations

A: To Draw Shear force and bending moment diagram. POC is the point of contraflexure. It is the point…

Q: Define Earthquakes.

A: Earthquake is any sudden ground shaking triggered by the seismic waves passing through rocks of the…

Q: Discuss MINIMUM COVER REQUIREMENTS AND STANDARD DIMENSIONS

A: Throughout reinforced concrete, the concrete cover is indeed the shortest route between the layer of…

Q: How is Ic = 0.3682 calculated through ratio and proportion? Show complete solution and neat…

A: to find - value of Ic based on graph . for further queries about question please upload full…

Q: What is the groundwater table, and what defines its position?

A: Groundwater table is the upper level of an underground surface where the soil or rocks are saturated…

Q: Define magma.

A: Magma is defined as the hot molten rock which is formed inside the crust level of the earth surface.…

Q: What is a boundary value problem? Where did it occur?

Q: Review the Seive Analysis and Hydrometer Analysis procedures by BS and ASTM and upload your…

A: Procedure of sieve analysis by British Standard: Material Required: Specimen Sieve Shaker BS 410…

Q: In the process of dividing a tract of land by a line running in a given direction, the surveyor…

Q: Find the area of the largest circle which can be cut from a square of edge 5 in. What is the area of…

A: The largest circle which cut out form the square of side a, then the diameter of the circle will be…

Q: plete solution with clear calculations , don't miss anything.

Q: 3. Given below is the technical description of Lot 2081, Cebu Cadastre. N Show your complete…

Q: clear and complete solution please

Q: 1. A contractor is to construct a tank to contain water for his construction project, given that the…

A: Given:- The height of the tank = 2.40 m The diameter of the tank = 2.80 m The dimensions of the GI…

Q: 2"

Q: Complete the table below. Area Cut or fill? 38.0 24.0 2 22.0 3 12.0 10.8 4 12 12

Q: Draw the figure/illustration. Show complete solutions

A: a.) Calculate the initial velocity Vi=VC2+HC2Vi=122+202Vi=23.32m/s Therefore the initial velocity is…

Q: Discuss the importance of the following sections: I) Compound sections II) Built-up sections

Q: Draw (A.F.).(S.F.) &( B.M.) diagrams for the following problems: 2t/m (1)

A: Jsosjsnsmsksl sjkswmmsksos jsksosnsgyebsk sjsksnjjdjdkdk dkdndmdkdk

Q: Complete the profile level notes shown below, perform the customary arithmetic check, provide a…

A: Solution: The table is formed as:

Q: detailed

Q: c)Components of Canal headworks. Subject: Irrigation Engineering

A: Any hydraulic structure which supplies water to the off taking canal is termed as canal headworks.

Q: Show FBD, all the step by step solution and neat handwritten.

Q: How to get TEC and TBC

A: Given data 0.77TEC + 0.8TBD = 1440...........(1) 0.514TEC - 1.6 TBD = 0...............(2)

Q: Illustrate a simple drawing plan of an aqueduct.

A: Cross Drainage structure are constructed at the intersection of a canal and a river ,so that the…

Q: A cylindrical steam boiler is to have a volume of 1340 cu ft. The cost of the metal sheets to make…

Q: omplete the different leveling notes by providing data to the unknown quantities. show solution

A: Given: The leveling notes are given below, STA BS HI FS ELEV BM1 1.256…

Q: What is the length of side CD and DE?

A: Let the length of line CD = L1 Latitude of line CD = L1-Cos 520 50' = -0.60 L1…

Concept explainers

Team Management

To complete a specific task or to accomplish organizational goals along with increasing work productivity, individuals need to come together and think along a common path and direction. There are certain tasks in an organization that cannot be done alone and the involvement of more individuals is essential. These groups of individuals who work together for a common goal compose a team and the individual members involved are known as team members.

Question

15) Please include complete solution and diagram if possible.

A line was determined to be 2,395.25 m when
measured with a 30-m steel tape supported
throughout its length under a pull of 4 kg at a mean
temperature of 35°C. Tape used is of standard
length at 20°C under a pull of 5 kg. Cross-sectional
area of the tape is 0.03 cm^2. The coefficient of
thermal expansion is 0.0000116/°C and the
modulus of elasticity of the tape is 2 million
kg/cm^2. Find the corrected length (in m) of the
line?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the magnitude (N) of the horizontal component of the reaction at point A if, F=500N, a=0.1m, b=2m, r=1.5m and d=30degrees
an open rectangular tank mounted on atruck is 8 m long and 1 m. wide. it is filled with water to a depth of 3.69 meters. if it is accelerated at 10.16 m/s^2 along its length, determine the required height (in meters) of the tank to prevent any water from spiling.
A reservoir contains water has a vertical circular orifice 25.2mm diameter and is first plugged up to measure any displacing force, the tank is suspended in a particular way. The horizontal force is required to keep the tank in place on the removal of the plug. The opposite applied force to the orifice is 16.8N. The volume per time was found as 141lt/minute. It is assumed that the level of the water is maintained at a constant height of 2.785m above the orifice. Calculate Cc, Cv, and Cd for the orifice.
A jet of water strikes with a velocity of 26.36 m/s on a flat plate, inclined at 30o with the axis of jet. If the diameter of the nozzle is 291 mm. Solve For:a) The force exerted by the jet on the plate.b) The components of the normal force.
A plate moves 10 cm/s to the right is 0.5 cm above a stagnant wall. The fluid bet. the plate and the wall has a viscosity of 1.8 cP. Compute the shear rate.
aceeleration = 4.905 m/s^2 to the right What is the gage pressure at A? in kpa.
The taped distance of a line is 86.67 meters using a 100 m. steel tape at a pull of 20 kg and temperature a 32°C. The tape is exactly 100 m. at a temperature of 28°C (supported throughout) and standard pull of 10 kg. If the coefficient of expansion of the tape is 0.00001 18, find the total correction for temperature.
Hydraulics ProblemAn open horizontal tank 1.5m high 2m wide and 5m long is full of oil with a specific gravity of 0.9. It is accelerated in the direction parallel to the longer length at 2.3 m/s2 a. What is the force acting on the wall of the tank with the shortest depth in KN? b. If the acceleration is increased by 0.88 m/s2. Determine the volume of oil that spilled out the tank?Note: Draw free-body diagram and used 4 decimal places
Water flows at the rate of 12 m³/s, at a depth of 1.5 m, in a 10 m wide irrigation canal. Assume uniform flow and use n=0.03521. Calculate the value of the specific energy. a. 1.81 J/N b. 1.53 J/N c. 1.74 J/N d. 1.65 J/N22. Compute the boundary shearing stress at the wall a. 7.33 Pab. 3.77 Pa c. 5.11 Pa d. 4.66 Pa
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
At 68 ˚F water has a dynamic viscosity of about 2.11 x 10 -5lb-s / ft2, solve the kinematic viscosity (in ft2/s) of water whose specific gravity is 0.998. Note ?????? =62.4 ??/??3 at normal condition.
Question 2) cage system of Figure F 1 = 131 kN , F 2 = 179 kN , θ = 38 ° and L = 4 m as photo migrants. According to this; Question 2-A) Find the rod force that occurs in the JI Question 2-B) Find the rod force that occurs in the DE rod. Question 2-C) Find the rod force that occurs in the JE rod.