termine the magr ut the corner A.

Q: -2 (2) y zy 4 (y 3) Simplify:

A: Following question is solved which belongs to the engineering mathematics under mechanical…

Q: Determine angle about P does the cone travel.

A: Given; As shown in figure:Right angled cone; With base radius 5 cm and height 12 cm It is rolled on…

Q: Determine the (f_y ) when force 80 Ib and angle 30° on the axis (X)

A:

Q: horizontal f ermine the

A: given data  coefficient of friction = 0.02 Load = 200N Force P is acting horizontal axis  required…

Q: Determine the (f_x) when force 90 N and angle 50° on the axis (Y)

A:

Q: E. Determine the largest W th

A: Need to determine Largest load (W)

Q: Determine the size of the shaft,

A: Given: P=22 kW N=550 rpm shear stress=42 MPa Tensile/compressive stress=56 MPa P=900 N L=2.5 m To…

Q: Dertermine the monet about point C

A:

Q: - length and the tio of the cross-se 10 am).

A: let the resistance of the wires is R length of wires is L resistivity of Copper , pc = 1.68 *10^-8…

Q: I repectively. d the mininMU orce pX

A:

Q: Redraw when the rack AB is aproaches parallel to horizontal. What are the other two angles belonging…

A: Given: Radius of the gear→r=200 mm=0.2 m If we represent the of the gear as O, then the distance OA:…

Q: 1. Thee points the Car tesian plane paints A (5.5; 13.2) ; B (15.1 j -8.1) and c(2.9; 14.5). lgoore…

A: Note: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for…

Q: Determine anglesr x, B to moin tain Luilibrium

A:

Q: Determine the length of the curve.

A: Given; A spatial curve in three dimensional space given in parametric form;   ⇒    xt= cos t⇒    yt…

Q: Deternine the moment of the foe ahut poiaO.

A: As per policy, we can solve only first three parts.

Q: h of the b

A:

Q: At the shown position OA is horizontal and is rotating count constant angular speed of 9 rad/s. Rod…

A: AC=2002-1002AC=173.205 mmB≡80+173.205,100,0B≡253.205,100,0A≡80,0,0 Position vector of point…

Q: determine the diameter o

A: Given data; A shaft is supported on two bearings as shown in figure:length =1.5 mIf shaft is…

Q: a Determine the Force gg AC 6 Determine the Forde AB 2' + 8' 350

A: Given: To find: Force AB , AC

Q: Q// Drow the 5.8.0 and B,m.D yougN

A: The shear force diagram for the beam is

Q: 4) The magnitude of the velocity of point E, (Ve in ft/s) =

A: here,we can find Ve from velocity triangle.so, first construct the velocity triangle with angle and…

Q: Determine the magnitude and location of the equi (N) w 60x N/m

A: given:

Q: Exalo S. F.d 4o KN/m Braw and B.M.d Ax=o,た Sohato Ay

A:

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: e the magnitude and orie ant force is directed along nitude of 1500N.

A:

Q: y, determine the required diameter of the rod.

A:

Q: ine the magnitude of thế mônment öf thě förce F about the corner A. F= 100 N

A: Given   Force, F = 100 N     Angle = 60o Find   Moment of force

Q: Dertermine the monet about point C loN

A:

Q: Re = 63 * lo4 if the = 0.25 Re = 63 * De termine ? 169

A:

Q: d. Determine the distance s required for the

A:

Q: foce thruugh force through B and comple and a coupl; 6

A: GIVEN DATA - A CANTILEVER TYPE BEAM GIVEN WE HAVE TO REPLACE FORCE WITH FORCE AND COUPLE

Q: ds. Determine the r it occurs in m.

A: given data elevation y= -0.13t4+4.1xt3 + 0.12 xt2 required  1) maximum velocity 2) elevation at…

Q: Hth of the belt, nece 1600 r.p.m and th the angle of cont

A: given:P=7.5kwd=300mmN=1600rpmμ=0.22θ=210

Q: N.m clockwise, and MB = 0. Determine P. %3D

A: p= -560N

Q: (b)show that: l(cosh at cos at) $3 st+4a4

A:

Q: . Find the width of the belt used it

A: To find width of belt (b)

Q: prave that B.A

A: The given question is about the proof of Commutative law for Dot product for vector quantity....

Q: Determine the flange thickness if the

A: To find Flange thickness

Q: determine the result o

A: Solution given below

Q: Determine the yof the shaded ared. L= 1.5m L -y = x² L

A:

Q: Ex. : Locate the centroie

A: GIVEN:

Q: ー25C

A: V=3*109 Volt U=75*109J

Q: Determine the length of diagonal CD, when (x=7 mm, y=4mm, z=5mm)

A: Given:x=7 mmy=4 mmz=5 mm

Q: elix angle a and e(i.c.

A:

Q: Q3=solve and ce 1 n The 44 quadrent f .circle

A: Given vector function is Fx,y=x+yi→+1-xj→ and the curve C∈x24+y29=1. The curve C∈x24+y29=1 is an…

Q: Determine the following: x, y, Ix, Iy

A:

Q: Determine P.

A: Given: P is in the xy plane moments of about O MO=80 Nm  (CCW)MA=200 NM  (CW)MB=0 To determine: The…

Q: reight of the rods and for the leflection (a) of point C, anč

A: given:

Q: Draw the moh'r circle

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.