The 12 kN crate is being pulled by the force P as shown in the figure. The force P makes an angle of e with the horizontal. a) Find the smallest possible force P to cause the crate to slide. b) Determine the angle e. c) Determine the horizontal frictional force acting at the bottom of the crate, W=12KN Note : The total surface R I Pmin - M= 0.20

The 12 kN crate is being pulled by the force P as shown in the figure. The force P makes an angle of e with the horizontal. a) Find the smallest possible force P to cause the crate to slide. b) Determine the angle e. c) Determine the horizontal frictional force acting at the bottom of the crate, W=12KN Note : The total surface R I Pmin - M= 0.20

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Similar questions

A billboard 3m high by 4m wide is supported as shown in the figure. The totl weight of the billboard is 30 kN. H = 1.5 m and tetha= 60 degrees. Wimd pressure, q= 1.6 kpa Wind pressure coefficient = 1.0. Determine the reactions at the support.
An equilateral triangle plate of side 2.4 m placed horizontally in a liquid (sp. gr. =0.80) in such a way that the center of the plate is 2.5 m below the free surface of water. a. Determine the area (in sq.meters) of the plate b. Determine the magnitude of the resultant force on the plate.
The cantilever beam is subjected to a concentrated load of P=20kips. The cross-sectional dimensions of the rectangular tube shapre are b=5.2in , d=8.10in , and t=0.400in. Determine:a) The magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer in ksi, rounded-off to 2 decimal places.b) The magnitude of the shear stress at point K, which is loacted to the left of the vertical centroidal axis zK=1.1in. Answer in ksi, rounded off to 2 decimal places.
Determine the minimum force P to prevent the 30-kg rod AB from sliding. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is μs = 0.2.
Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine the increase in vertical stress at point A located z = 15 ft below the surface. Given: x = 27 ft. Figure P6.4
If d = 450 mm, determine the absolute maximum bending stress in the overhang beam.
The solid circular shaft is subjected to an internal torque of T= 6.0 kN.m. Determine the shear stress developed at point A and B
Determine the magnitude and location of the resultant hydrostatic forceacting on the submerged rectangular plate AB shown.The plate has a width of 1.5 m; ρw = 1000 kg/m3.
A 2.8m square plate is completely immersed under water in a vertical position such that the two edges of the square are horizontal. It is immersed such that the center of pressure is located 8cm below its center of gravity. Determine the resultant hydrostatic force on one side of the plate.
a horizontal single force P of 150 lb magnitude is applied to the end D of lever ABD. 1. what is the normal and shear stresses at point H having sides parallel to the x and y axes? 2. determine the principal planes and pricipal stress at the point H
The uniform sign has a weight of 1500 lb and is supported by the pipe AB, which has an inner radius of 2.75 in. and an outer radius of 3.00 in. If the face of the sign is subjected to a uniform wind pressure of p = 150 lb>ft2, determine the state of stress at points C and D. Show the results on a differential volume element located at each of these points. Neglect the thickness of the sign, and assume that it is supported along the outside edge of the pipe.
Determine the vertical displacement at Joint A, B, C, D, E