I am not entirly sure what system this problem is decribing. what do the fbd's for this look like? The 2-kg spool S fits loosely on the inclined rod forwhich the coefficient of static friction is μ = 0.16.(Figure 1)FigureA0.25 m<41 of 1>Part AIf the spool is located 0.25 m from A, determine the maximum constant speed the spool can have so that itdoes not slip up the rod.Express your answer to three significant figures and include the appropriate units.V =0SubmitμÅValueRequest AnswerUnits?

Answered: Image /qna-images/answer/d5d746f6-e6f8-4c4f-be45-e6e5e34db689.jpg

The 2-kg spool S fits loosely on the inclined rod for which the coefficient of static friction is = 0.16. (Figure 1) Figure 0.25 m 1 of 1 Part A If the spool is located 0.25 m from A, determine the maximum constant speed the spool can have so that it does not slip up the rod. Express your answer to three significant figures and include the appropriate units. V = μA Value Submit Request Answer Units ?

The 2-kg spool S fits loosely on the inclined rod for which the coefficient of static friction is = 0.16. (Figure 1) Figure 0.25 m 1 of 1 Part A If the spool is located 0.25 m from A, determine the maximum constant speed the spool can have so that it does not slip up the rod. Express your answer to three significant figures and include the appropriate units. V = μA Value Submit Request Answer Units ?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.56P: The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The...

See similar textbooks

Similar questions

The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
The 600-lb cable spool is placed on a frictionless spindle that has been driven into the ground. If the force required to start the spool rotating is F = 160 lb, determine the coefficient of friction between the ground and the spool. Neglect the diameter of the spindle compared to the diameter of the spool.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
A pulley with a diameter of 4 in. can rotate about a fixed shaft with a diameter of 2 in. The coefficient of static friction between the pulley and shaft is 0.20. Determine; a. the smallest vertical force P required to start raising a 500-lb load. b. thesmallest vertical force P required to hold the load. c. the smallest horizontal force P required to start raising the same load.
Block A weighs 10.5 lb and block B weighs 6.5 lb. The static friction coefficient between blocks A & B is 0.32. The static friction coefficient between blocks B and the inclined surface is 0.37. If the incline is ? = 30∘ what is the smallest force P required for motion?
The masses of the blocks are mA = 30 kg and mB = 70 kg. Between all of the contacting surfaces the coefficient of static friction is 0.1. 1. What is the largest force F that can be applied without causing the blocks to slip? 2. What is the reaction between the two blocks? 3. What is the reaction between the floor and block B
1. A truck is weighing 1.4 KN moves up a slope of 15 °. What is the force generated by the engine if the truck is accelerating at a rate of 3 m/s2? Assume the coefficient of friction is μ =0.1.
1. If there is no friction between shaft AB and the collar, what angular velocity θ˙˙ must the mechanism have to keep the collar at r=300 mm from the vertical axis? Express your answer to three significant figures. 2. Consider the same mechanism again, with m=2.95 kg, d=225 mm, k=250 N/m, only now, instead of being smooth, the collar and shaft have a maximum coefficient of friction of μs=0.297. What is the minimum angular velocity required to keep the collar at a constant distance r=300 mm from the axis of rotation? Express your answer to three significant figures.
The crate has a weight of W = 350 lb, and the coefficients of static and kinetic friction are μs = 0.3 and μk = 0.2, respectively. Determine the friction force on the floor if θ = 47.4° and P = 105 lb.
The motorcycle weighs 151 kg and the driver weighs 64 kg. Dimension l1 = 0,31 m ja l2 = 0,23 m Determine the required coefficient of friction
The homogeneous 322-lb body A of Fig. P10-30 is moving to the right with a velocity of 6 fps. The coefficient of friction between A and the horizontal plane is 0.2. Determine the maximum weight body B may have without causing A to tip.
Crates A and B are connected by cable CD and rest upon a wooden plank as shown above. Crate A weighs 225 lbs and crate B weighs 175 lbs. An additional force P can be applied to crate B which is parallel to the plank.The coefficient of static friction between crate and plank is μs = 0.25 for both crates.The wooden plank is able to be raised to any angle θ.Neglect the weight of the cable. A. If no external forces are applied ( P = 0 ) and the plank is gradually raised, which crate starts slipping first? B. If no external forces are applied ( P = 0 ) and the plank is gradually raised, at what angle does the crate chosen from part A start slipping? C. If the plank is raised to θ = 20° what is the minimum external force P that can be applied in order to prevent the crates from slipping?