The 2 m long bar BC weighing L touches the polished surface at a point 1 m away from point A. The rod is held in balance with the AB rope. Calculate the reaction force at point C and the force on the rope. (hint: The stick is at a 60-degree angle with the wall.)

Q: The quadriceps tendon attaches to the tibia at a 30° angle 4 cm from the joint center at the knee.…

A: for the quadriceps attaches to the tibia according to the given information we have to solve for the…

Q: The jib crane is designed for a maximum capacity of 5 kN, and its uniform I-beam has a mass of 200…

A: To Find : The resultant force at x=0.8m. Given :  The maximum capacity is 5kN The mass of beam is…

Q: he 30-lb homogeneous bar AB supports the 60-lb block. The ends of the bar rest on frictionless…

A:

Q: A 3 m long steel rod with a mass of 5000 (kg) is lifted from its ends in balance with a 6 m long…

A:

Q: Sphere A weighs 275 lb and Shere B weighs 205 lb. Assume all surfaces are frictionless. What…

A:

Q: The mass of the uniform bar AB is 40 kg. Calculate the couple C required for equilibrium if a. 0 = 0…

A: Given data as per question Mass of bar =40 kg  considering Free body diagram of the system

Q: Two massless and frictionless pulleys are used to drag a large mass (m = 645 kg) up an inclined…

A:

Q: A wheel of mass M has radius R. It is positioned vertically on the floor and you exert a horizontal…

A:

Q: The 60-kg homogeneous disk is resting on the inclined friction surface. Compute the magnitude of…

A:

Q: A 100-m, 10 N uniform rods carries 20-N and 30-N weights suspended at its ends, as shown. Where…

A: Given data,  P1= 20 N  P2= 30 N  Length of rod is L= 100 m

Q: The 45-kg homogeneous smooth sphere rests on the 42° incline A and bears against the smooth vertical…

A: Mass of sphere, m=45 kgInclination angle of A, θ=42o

Q: A stone of mass ? = 0.1 ??, attached to the end of a 1 ? long rope, rotates in the direction of the…

A: Given, Mass, m=0.1 kg Tangential velocity, v=10 m/s Radius, r=0.1 m θ=370

Q: A wheel of 10 in. radius carries a load of 1000 lb. a. Determine the horizontal force P applied at…

A:

Q: The linkage of the braking system consists of the pedal arm DAB, the connecting rod BC, and the…

A:

Q: Practice Problem 4.4.9: The centers of gravity of the 50- kg lift truck and the 120-kg box are at G1…

A: Given, The mass of lift truck, m1=50 kg The mass of the box, m2=120 kg Pushing force, P=600 N

Q: The homogeneous 300-kg cylinder is pulled over the 100-mm step by the horizontal force P. Find the…

A: for un-equilibrium conditions the moment due to the force P about the pivot should be greater than…

Q: The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 230…

A:

Q: 200 N A block placed under the head , of the claw hammer as shown greatly facilitates the extraction…

A: → Consider the free body diagram of the above figure ,

Q: deflection of the uniform 100-kg beam the 60-kg boy exerts a pull of 150 N on the rope rigged as…

A: Given that ;  WB=60kgWbeam=100kgT=150N

Q: Pulley A delivers a steady torque of 1100 lb-in. To a pump through its shaft at C. The tension in…

A:

Q: The 100 kg C ring moves on the BD rod without friction. Calculate the force on the AC chain for the…

A:

Q: A system of three pin connected bars takes the depicted equilibrium position under the given loading…

A: Given data: Three-pin connected bars.

Q: (i) Make a rough copy of the figure. Draw arrows on your copy to show the weight of the object and…

A:

Q: The mass of the uniform bar AB is 40 kg. Calculate the couple C required for equilibrium if (a) θ =…

A: (a) Consider the free body diagram as shown below.

Q: The constant moment of 100 Nm is applied to the crank shaft. Determine the compressive force P that…

A: givenconstant moment on crank shaft T=100Nmcompresive force acting on piston=Pangle between verical…

Q: The crane's arm has a pin support at A. The hydraulic cylinder BC exerts a force on the arm at C in…

A: The Answer is Below

Q: The jib crane is designed for a maximum capacity of 9 KN, and its uniform I-beam has a mass of 260…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Using the equilibrium concept, calculate the magnitude of F1 and its direction ф as shown in the…

A:

Q: The skid-steer loader has a mass of 1.18 Mg, and in the position shown. The center of mass is at G1.…

A:

Q: Q.2 The 50-KN smooth sphere rests on the 30° inclined A and bears against the smooth vertical wall…

A:

Q: . Determine the angle ” between the table and the plane face of the hemisphere in its equilibrium…

A: Draw a free-body diagram of a given system with dimensions.

Q: The pulley system shown in Figure Q1c lifts a mass,m,of 550 kg.Calculate the force FA necessary to…

A:

Q: The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts…

Q: The jib crane is designed for a maximum capacity of 14 kN, and its uniform l-beam has a mass of 270…

A:

Q: A crane boom is supported as shown. The boom has a mass of 660 kg and the box on the end of the…

A: given boom has a mass , M=660 kgbox has a mass, m=98×10=980kglength of boom, L=15mcable angle with…

Q: Q2: The square steel plate has a mass of 1800 Kg with mass center at its center G. calculate the…

A: Given Data: The mass of the square plate is M= 1800 kg. The coordinate of point B is…

Q: The 39-kg homogeneous smooth sphere rests on the 36° incline A and bears against the smooth vertical…

A: Given:-m=39 kgθ=36°To find:-Find reaction forces at A and B

Q: For what value M of the clockwise couple will the horizontal component of the pin reaction at C be…

A: Given data: CB = 8 feet AB = 4 feet P = 100 lb theta = 45 deg

Q: . Determine the force components acting on ball joint A, the reaction at roller B, and the tension…

A:

Q: To test the deflection of the uniform 125-kg beam the 70-kg boy exerts a pull of 100 N on the rope…

A:

Q: d of mass m, = 163 g and length L = 100.0 cm is attached to the wall with a pin as shown. Cords are…

A: Givenuniform rod mass mr=163glength of the rod L=100cmmass m1=251gmass m1 distance from pin,…

Q: he 100 kg C ring moves on the BD rod without friction. Calculate the force on the AC chain for the…

A: The vector from B to C is nowrBC=8meter  eBD     =849i-79j+49k

Q: Draw the free-body diagram of the uniform bar, which has a mass of 100 kg and a center of mass at G.…

A:

Q: he elements of the spring loaded mechanism for the car tailgate are shown in the figure. For the…

A:

Q: The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs.…

A:

Q: Find the smallest distance d for which the hook will remain at rest when acted on by the force P.…

A: To determine the distance d for which the hook will remain at rest.

Q: of body B in the figure that will permit the homogenous50lb block A to slide without tipping over.…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.