The 200-mm-radius brake drum is attached to a larger Bywheel. The total mass moment of inertia of the flywheel and drum is 19 kg. and the coefficient of kinetic friction between the drumand the brake shoe is 035, Knowing that the initial angular velocity of the flywheel is 180 rpm clockwise, determine the vertical force P that must be applied to the pedal C if the system is to stopin 100 revolutions.150 mm250 mmBne:P= 172.88 NC375 mm200 mm

Answered: Image /qna-images/answer/072f001a-7cf3-4992-810a-ffaa85b9e9ae.jpg

The 200-mm-radius brake drum is attached to a larger Bywheel. The total mass moment of inertia of the flywheel and drum is 19 kg and the coefficient of kinetic friction between the drum and the brake shoe as 0.35 Knowing that the initial angular velocity of the flywheel is 180 rpm clockwise, determine the vertical force P that must be applied to the pedal C if the system a to stopa in 100 revolutions 150 mm 250 mm B -375 mm 名。 200 mm

The 200-mm-radius brake drum is attached to a larger Bywheel. The total mass moment of inertia of the flywheel and drum is 19 kg and the coefficient of kinetic friction between the drum and the brake shoe as 0.35 Knowing that the initial angular velocity of the flywheel is 180 rpm clockwise, determine the vertical force P that must be applied to the pedal C if the system a to stopa in 100 revolutions 150 mm 250 mm B -375 mm 名。 200 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 10-in.-radius brake drum is attached to a larger flywheel which is not shown. The total mass moment of inertia of the flywheel and drum is 22 lb ⋅ ft ⋅ s 2 and the coefficient of kinetic friction between the drum and the brake shoe is 0.41. Knowing that the initial angular velocity is 255 rpm clockwise, determine the force which must be exerted by the hydraulic cylinder at point B if the system is to stop in 85 revolutions.
The 10-in.-radius brake drum is attached to a larger flywheel which is not shown. The total mass moment of inertia of the flywheel and drum is 22 lb ⋅ ft ⋅ s 2 and the coefficient of kinetic friction between the drum and the brake shoe is 0.41. Knowing that the initial angular velocity is 255 rpm clockwise, determine the force which must be exerted by the hydraulic cylinder at point B if the system is to stop in 85 revolutions. determine the force which must be exerted by the hydraulic cylinder at point B if the system is to stop in 85 revolutions. DO NOT ROUND OFF IN THE SOLUTION. ROUND OFF ONLY IN 2 DECIMAL PLACE IN THE FINAL ANSWER.
The 8-in. radius brake drum is attached to a larger flywheel that is not shown. The total mass moment of inertia of the drum and the flywheel is 15 lb.ft.s2 and the coefficient of kinetic friction between the drum and the brake shoe is 0.40. Knowing that the angular velocity of the flywheel is 450 rpm clockwise when a force P of magnitude 65 lbf. is applied to the pedal C, determine the number of the revolutions executed by the flywheel before it comes to rest. (The final answer should be in two decimal places with correct units)
The 10-in.-radius brake drum is attached to a larger flywheel which is not shown. The total mass moment of inertia of the flywheel and drum is and the coefficient of kinetic friction between the drum and the brake shoe is 0.40. Knowing that the initial angular velocity is 240 rpm clockwise, determine the force that must be exerted by the hydraulic cylinder if the system is to stop in 75 revolutions.
A drum of 40 mm radius Is attached to a disk of 100 mm radlus. The disk and drum have a total mass of 4 kg and a combined radius of gyration of 90 mm. A cord is attached as shown and pulled with a force P of magnitude 20N. Knowing that the disk rolls without sliding. determine the minimum value of the coefficient of static friction compatible with this motion. none of them B) us-0.15 Us-0.25 D) ps=0.229
The rotor of an electric motor has an angular velocity of 3570 rpm when the load and power are cut off. The 65-kg rotor, which has a centroidal radius of gyration of 175mm, until it reaches the maximum speed of 5250 rpm. Knowing that the kinetic friction results in a couple of magnitude 4.5 N.m exerted on the rotor, determine the number of revolutions that the rotor executes, before achieving its maximum speed and the time it took. (The final answer should be in two decimal places with correct units)
Hey, please reply as soon as POSIBLE! Wheel A, of 30kg, is located in the position shown by the effect of idler wheel D (frictionless wheel) and the system rope-spring BC. The static coefficient of friction is 0.50 and the kinetic coefficient is 0.40 between all the contact surfaces. If the force exerted by the horizontal spring is 60 N: a) Determine whether or not wheel A is turning when a moment M of 60 Nm is applied at point G. b) If it is shown that under the previous condition the wheel is turning, calculate the new value of the moment M necessary for the wheel to keep turning in equilibrium. Also indicate the frictional force that is generated at point F under that condition.
The 12-lb uniform disk shown has a radius of r = 3.2 in. and rotates counterclockwise. Its center C is constrained to move in a slot cut in the vertical member AB, and an 11-lb horizontal force P is applied at B to maintain contact at D between the disk and the vertical wall. The disk moves downward under the influence of gravity and the friction at D. Knowing that the coefficient of kinetic friction between the disk and the wall is 0.12 and neglecting friction in the vertical slot, determine (a) the angular acceleration of the disk, (b) the acceleration of the center C of the disk.
A drum of 4-in. radius is attached to a disk of 8-in. radius. The disk and drum have a total weight of 10 lb and a combined radius of gyration of 6 in. A cord is attached as shown and pulled with a force P of magnitude 5 lb. Knowing that the disk rolls without sliding, determine (a) the angular acceleration of the disk and the acceleration of G, (b) the minimum value of the coefficient of static friction compatible with this motion.
A band and block brake having 10 blocks, each of which subtends an angle of 14o at center, is applied todrum of effective diameter of 1 m. The brake drum and winding drum of crane mounted on the sameshaft weighs 20 kN and have combined radius of gyration of 300 mm. The two ends of the band areattached to the pin on opposite side of the fulcrum. If an effort of 300 N is applied at distance of 800mm from the fulcrum, find (i) Braking torque, (ii) the angular retardation of the brake, (iii) the timetaken by the system to come to rest from the rated speed of 400 rpm. Take coefficient of frictionbetween the drum and the block as 0.25.
The 200mm 1.2kg BD rod; and the 1.5 kg piston P are connected through the mechanism shown. 90mm AB crank rotates at constant 1200 rpm counterclockwise and angle θ=50 °. Determine the reactions at joints B and D, do not consider friction between cylinder and piston P.
A cylinder of radius r and weight W with an initial counterclockwise angular velocity w0 is placed in the corner formed by the floor and a vertical wall. Denoting by μk the coefficient of kinetic friction between the cylinder and the wall and the floor, derive an expression for the time required for the cylinder to come to rest.