The 24-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E= 200 GPa. (Figure 1) Figure A 600 mm B 400 mm 50 kN 50 kN C 40 kN 1 of 1 ▾ Part A Determine the displacement of end C with respect to the fixed support at A Express your answer to three significant figures and include the appropriate units. Sc= Value Submit HA Provide Feedback 5 Request Answer Units B ? D

The 24-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E= 200 GPa. (Figure 1) Figure A 600 mm B 400 mm 50 kN 50 kN C 40 kN 1 of 1 ▾ Part A Determine the displacement of end C with respect to the fixed support at A Express your answer to three significant figures and include the appropriate units. Sc= Value Submit HA Provide Feedback 5 Request Answer Units B ? D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.9.11P: A hollow circular tube A fits over the end of a solid circular bar B, as shown in the figure. The...

See similar textbooks

Similar questions

Repeat Problem 2.4-8, but assume that the bar is made of aluminum alloy and that BC is prismatic. Assume that P = 20 kim. L = 3 ft.t = 314 in., b1 2m.b 2.Sin.andElO.400ksi.
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A hollow circular tube A fits over the end of a solid circular bar B, as shown in the figure. The far ends of both bars are fixed. Initially, a hole through bar B makes an angle ß with a line through two holes in tube A. Then bar B is twisted until the holes are aligned, and a pin is placed through the holes. When bar B is released and the system returns to equilibrium, what is the total strain energy U of the two bars? (Let lAand lBrepresent the polar moments of inertia of bars A and B, respectively. The length L and shear modulus of elasticity G are the same for both bars.)
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
A hand cranking lever, as shown in Figure 6 below, is used to start a truck engine byapplying a force F = 400 N. The material of the cranking lever has a yield strength = 320 MPa;Ultimate tensile strength = 500 MPa; Young’s modulus = 205 GPa; Modulus of rigidity = 84 GPaand poisson’s ratio = 0.3. Assuming factor of safety to be 4 based on yield strength, design thediameter of the lever at section X-X near the guide bush using: a) Maximum distortion energytheory; and b) Maximum shear stress theory.
A helical compression spring is to be used for a maximum load of 1.5 kN using the spring index of 8. The maximum permissible shear stress for the spring wire is 400 MPa. Which of the following is the wire diameter of the spring to be used?
Steel bar in shape, AAB 600 mm and ABc = DACD3D 1200 mm2 are made of two stages. Determine the displacement at end A in (mm). E = 200 GPa
An arrow is shown, where the most critical part (r) of said arrow is observed.to. It is designed with approximate relative sizes of d = 0.65D and r = D/15 with the diameter d conforming to the size of the inner diameters of standard metric bearings.b. It is made of SAE 2340 steel, heat treated to obtain minimum strengths in the shoulder area of Sut = 1226 MPa and Sy = 1130 MPa.c. At the shoulder, the arrow is subjected to a completely reversible bending moment of M = 80N and a uniform torque of T = 55Nmd. It has a safety factor n = 2 Determine the dimensions of the shaft for infinite life.
Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque T0 = 10 kN.m is applied at point D. (a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm.
Two steel springs arranged in series support a load P. The upper spring has 12 turns of 25 mm diameter wire on a mean radius of 100 mm. The lower spring consists of 10 turns of 20 mm diameter wire on a mean radius of 75 mm. Use G = 83 GPa. Which of the following most nearly gives the value of the total elongation of the assembly? Which of the following most nearly gives the equivalent spring constant of the assembly? Which of the following most nearly gives the maximum value of P if the allowable shearing stress is 200 MPa?
The figure (attached) shows a belt pulley mechanism which is loaded statically. The shaft is made of AISI 1030 steel with the yield strength of 480 MPa. Using distortion energy theory (DET), determine the diameter of the shaft with a factor of safety of 2.
A vertical shaft is supported by two deep groove ball bearings as shown below. The shaft will be driven by vee belts through a pulley. The combined tensions of the belt apply and the weight of the pulley assembly applies a force of 5.4kN and 900N respectively. The shaft has a diameter of 32mm. Bearing A at the top supports the shaft radially whereas bearing B at the bottom supports the shaft axially and radially. Two deep groove ball bearings have been selected for this application. The models of the bearings are SKF 6305 and SKF 6205 for bearing A and B respectively. a) What are the forces at bearing A and B? b) Paste a screenshot of the graph showing the distribution of the forces in the shaft. c) From the report, find the static load capacity for: Bearing A Bearing B