The 28-in-diameter pump in Fig. 11.7a at 1170 r/min is used to pump water at 20°C through a piping system at 14,000 gal/min. (a) Determine the required brake horse- power. The average friction factor is 0.018. (b) If there is 65 ft of 12-in-diameter pipe upstream of the pump, how far below the surface should the pump inlet be placed to avoid cavitation?

The 28-in-diameter pump in Fig. 11.7a at 1170 r/min is used to pump water at 20°C through a piping system at 14,000 gal/min. (a) Determine the required brake horse- power. The average friction factor is 0.018. (b) If there is 65 ft of 12-in-diameter pipe upstream of the pump, how far below the surface should the pump inlet be placed to avoid cavitation?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A propeller turbine develops 12,000hp, and rotates at 145rpm under a head of 20m. The outer and hub diameters are 4m and 1.75m, respectively. Calculate the inlet and outlet blade angles measured at mean radius if overall and hydraulic efficiencies are 85% and 93%, respectively. Show schematic diagram and provide solutions.
A volute centrifugal pump with an impeller diameter of 0.02 m has the following performance data when pumping water at the best efficiency point: impeller speed N = 58.3 revs/s capacity Q = 0.012 m3/s total head Ah = 70m required net positive suction head NPSH = 18m brake power Pe = 12000w Determine the new performance data (listed above) of a homologous pump with twice the impeller diameter operating at half the impeller speedand same efficiency.
Ex.2: In a test of the centrifugal pump shown in Fig. below, the following data are taken: py =100 mmHg (vacuum) and pz = 500 mmHg (gage). The pipe diameters are D1 = 12 cm and Dz = 5 cm. The flow rate is 180 gal/min of light oil (SG =0.91). Estimate (a) the head developed, in meters, and (b) the input power required at 75 percent efficiency. — -—
A certain centrifugal pump was tested and its performance curves can be approximated as follows: H = 340 - 1.2(Q2), in feet BP = (0.0521Q3) + (1.25Q2) + (11.042Q) + 134.5, in horsepower where Q is in ft3/s. If two of this pump is connected in series to deliver water to a system whose head requirement is 615 ft, what will be the operating discharge rate in ft3/s of either pumps? Assuming the head is equally divided between the two pumps, what is the efficiency of either pumps (in %)? Take the specific weight of water to be 62.4 lbf/ft3.
A double suction centrifugal pumps delivers 25ft3 of water at a head of 12m and running at 650rpm. What is the specific speed of the pump? ANSWER: 3097.77rpm
Fluid Mechanics. plz, solve all the parts from a , b and c Reg.no : 5395 Pb # 6: At its optimum point of operation, a given centrifugal pump with an impeller diameter of 500 mm delivers a 4 m3/s of water against a head of (Reg.No/100) m when rotating at 1500 rpm. (a) If its efficiency is 82%, what is the brake power of the drive shaft? (b) If a homologous pump with a diameter of 800 mm is rotating at 1200 rpm, what would be the discharge, head, and shaft power. Assume both operate at the same efficiency. (c) Compute the specific speed of both pumps. What type of pumps are these?
It is proposed to build a three- stage centrifugal pump to deliver 4000 kg/min of water at a speed of 900 rpm under a total manometric head of 70 m. The vanes are to be radial at inlet and are to be curved backwards at exit at an angle of 45°. Assuming manometric efficiency of 84% and overall efficiency of 75% and considering that vane thickness accounts for 8% of circumferential area. The velocity of flow may be assumed constant at 2.5 m/sec. The probable external diameter is ؟
It is proposed to build a three- stage centrifugal pump to deliver 4000 kg/min of water at a speed of 900 rpm under a total manometric head of 70 m. The vanes are to be radial at inlet and are to be curved backwards at exit at an angle of 45°. Assuming manometric efficiency of 84% and overall efficiency of 75% and considering that vane thickness accounts for 8% of circumferential area. The velocity of flow may be assumed constant at 2.5 m/sec. The outlet peripheral speed is ؟
It is proposed to build a three- stage centrifugal pump to deliver 4000 kg/min of water at a speed of 900 rpm under a total manometric head of 70 m. The vanes are to be radial at inlet and are to be curved backwards at exit at an angle of 45°. Assuming manometric efficiency of 84% and overall efficiency of 75% and considering that vane thickness accounts for 8% of circumferential area. The velocity of flow may be assumed constant at 2.5 m/sec. The width of each impeller is , The probable external diameter is , The outlet peripheral speed is , The h.p. input necessary is
It is proposed to build a three- stage centrifugal pump to deliver 4000 kg/min of water at a speed of 900 rpm under a total manometric head of 70 m. The vanes are to be radial at inlet and are to be curved backwards at exit at an angle of 45°. Assuming manometric efficiency of 84% and overall efficiency of 75% and considering that vane thickness accounts for 8% of circumferential area. The velocity of flow may be assumed constant at 2.5 m/sec. The width of each impeller is ؟
It is desired to construct a hydraulic turbine for a hydraulic power plant to operate under the following conditions: discharge Q = 3.5 m3/s of water, the available net head = 290 meters, the hydraulic efficiency = 0.8, the rotating speed = 300 rpm. A Pelton wheel impulse turbine was selected with the following specifications: the bucket angle b2 = 160°, the coefficient of velocity for the nozzle is 0.98 and assume the friction coefficient k = 0.2. Determine the following:Jet Diameter to Wheel diameter ratio, dj/Dw. The Specific Speed in M.K.S., Ns.The computed head coefficient ϕ.The brake horsepower. The required number of Jets. The Pelton wheel diameter in meters.
An existing pump is used to pump water with the following data at BEP: D = 2.15 in, N = 1784 rpm, ρ = 998 kg/m3, Q = 18 gpm, H = 4.2 ft. A larger pump is to be designed based from the existing one to be used for pumping slurry (ρ = 1220 kg/m3) such that its best efficiency point occurs as close as possible to a volume flow rate of 48 gpm and at a net head of 15 ft. Calculate the new pump diameter in inches. Round off your final answer to 3 decimal places.