The 30-kg uniform thin hollow square plate is pinned at point 0, and its side L = 0.2 m. If it is subjected to the constant moment M = 62 N•m and is released from rest from the position as shown, determine the total work done to it when it has rotated 45. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper Sl unit. Take g = 9.81 m/s².

The 30-kg uniform thin hollow square plate is pinned at point 0, and its side L = 0.2 m. If it is subjected to the constant moment M = 62 N•m and is released from rest from the position as shown, determine the total work done to it when it has rotated 45. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper Sl unit. Take g = 9.81 m/s².

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.57P: Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.

See similar textbooks

Similar questions

Determine the largest angle for which the homogeneous block remains at rest.
The 2000 kg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC. The diameters of AB and AC are 12 mm and 10 mm, respectively. Determine the weight of the concrete pipe ( in N).
How much work is done by the force in the spring when the slender rod rotates clockwise about the fixed pin support at O from the vertical position (where AB is horizontal) to the horizontal position? The spring has a stiffness of k = 125 N/m and an unstretched length of 0.15 m. Take d1= 0.29 m and d2= 0.85 m. Choose the correct answer. a) 94.9 Joule b) 99.9 Joule c) -99.9 Joule d) 0 Joule e) -94.9 Joule
The cylinder having a diameter 2.5 ft weighs 57 lb and is 6 ft long. Determine the reaction (lb.) at A neglecting friction. Determine the reaction at B (lb.) neglecting friction. Weight density of water is 62.4 lb/ft3 Sp.gr Gs = 1.6
3. Determine whether the 10 kg block shown is in equilibrium, and find the magnitude and direction of the friction force when P = 40 N and 0 = 20⁰. μ = 0.30 M = 0.25 20°
Both pulleys are fixed to the shaft and as the shaft turns with constant angular velocity, the power of pulley A is transmitted to pulley B. Determine the horizontal tension T in the belt on pulley B and the x, y, z components ofreaction at the journal bearing C and thrust bearing D if θ = 0°. The bearings are in proper alignment and exert only force reactions on the shaft.
If the block remains in the equilibrium position shown, determine the mass of the block D. The unextended length of spring AB is 9 m. d1 = 8 m d2 = 10 m KAC = 44 N/m KAB = 70 N/m Mass of block D = ____ kg
The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. If the 100-N pull is then removed, find the distance the block will travel. the answer must 3 decimal places.
The motorcycle in the figure has a mass of m1 kg and its center of mass is at G1. The mass of the driver is m2 kg and the center of mass is at G2. Since there is μs between the wheels and the asphalt, determine whether it is possible for the driver to lift the front wheel off the ground. Neglect the mass of the wheels and assume that the front wheel can spin freely. a=0.41 m b= 0.39 m c= 0.75 m d= 0.25 m e=0.58 m m1=120 kg m2= 77 kg μs=0.82
The mass is 60kg. determine: a)the magnitude F. b)the components of reaction at thrust bearing at A and smooth journal bearing at B.
Determine the mass of the R-134a.
Determine the maximum mass of the lamp that the cord system can support so that no single cord develops a tension exceeding 320 N .