The 40-kg square homogeneous plate is held in the vertical plane by three cords at the position - 60%. Then the cord FG is cut and the plate begins to move. Determine the acceleration of the plate center C and tensions in the cords AD and BE when the angle 8-90%. The side length of the plate is 10 cm.

The 40-kg square homogeneous plate is held in the vertical plane by three cords at the position - 60%. Then the cord FG is cut and the plate begins to move. Determine the acceleration of the plate center C and tensions in the cords AD and BE when the angle 8-90%. The side length of the plate is 10 cm.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.20P: The 3600-lb car with rear wheel drive is attempting to push the 4500-lb crate. The center of gravity...

See similar textbooks

Similar questions

If the mass of cylinder C is 40 kg, determine the mass of cylinder A in order to hold theassembly in the position shown in the figure.
The figure below is a system consisting of two masses MA = 1.82 kg and MB = 3.6 kg, whose distance from the pore axis is R₁ = R₂ = 15 cm, while the angular positions are 0₁ = 30° and 0 = 150° . Determine the weight and position of the balancing mass placed on planes C and D if the distance from the axis RC = RD = 15 cm.
Packaging for apples is tested using a machine that exerts accelaration components ay = 10 m/s2 and ax = 5 m/s2, simultaneously. Select the correct FBD and kinetic diagram for this condition. A. B. C. D.
The motorcycle in the figure has a mass of m1 kg and its center of mass is at G1. The mass of the driver is m2 kg and the center of mass is at G2. Since there is μs between the wheels and the asphalt, determine whether it is possible for the driver to lift the front wheel off the ground. Neglect the mass of the wheels and assume that the front wheel can spin freely. a=0.41 m b= 0.39 m c= 0.75 m d= 0.25 m e=0.58 m m1=120 kg m2= 77 kg μs=0.82
Rod OA rotates counterclockwise at a constant angular rate θ˙ = 4 rad/s. The double collar B is pin-connected together such that one collar slides over the rotating rod and the other collar slides over the circular rod described by the equation r=(1.6cosθ)m. Both collars have a mass of 0.7 kg . Motion is in the horizontal plane. (Figure 1)
The sports car, having a mass of 1700 kg, travels horizontally along a 20° banked track which is circular and has a radius of curvature of p = 100 m. Determine the normal force of the car in Newton.
The 5 kg cylinder is released from rest in the postion shown in the figure below. Determine the maximum compression xmax of the spring. The stiffness of the spring is 1800 N/m.
The 2000 kg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC. The diameters of AB and AC are 12 mm and 10 mm, respectively. Determine the weight of the concrete pipe ( in N).
The cylinder having a diameter 2.5 ft weighs 57 lb and is 6 ft long. Determine the reaction (lb.) at A neglecting friction. Determine the reaction at B (lb.) neglecting friction. Weight density of water is 62.4 lb/ft3 Sp.gr Gs = 1.6
If both carriages have a total mass of 200 g and the sliding carriage is at a radius of 20 cm, what radius in cm should the fixed carriage be at?
The drop gate at the end of the trailer has a mass of 1000 kg and mass center at G. If it is supported by the cable AB and hinge at C. determine the tension in the cable when the truck begins to accelerate at 5 m/s2 to the left.
A demonstration gyroscope wheel is constructed by removingthe tire from a bicycle wheel 0.650 m in diameter, wrapping leadwire around the rim, and taping it in place. The shaft projects 0.200 mat each side of the wheel, and a woman holds the ends of the shaft inher hands. The mass of the system is 8.00 kg; its entire mass may be assumedto be located at its rim. The shaft is horizontal, and the wheel isspinning about the shaft at 5.00 rev/s. Find the magnitude and directionof the force each hand exerts on the shaft (a) when the shaft is at rest;(b) when the shaft is rotating in a horizontal plane about its center at0.050 rev/s; (c) when the shaft is rotating in a horizontal plane about itscenter at 0.300 rev/s. (d) At what rate must the shaft rotate in order thatit may be supported at one end only?