The 45 kg piston is supported by a spring of modulus k = 35 kN/m. A dashpot of damping coefficient 'c' = 1250 N-s/m acts in parallel with the spring. A fluctuating pressure P = 4000 sin30t in Pa acts on the piston as shown in figure below, whose top surface area is 50x10-³ m². The steady-state amplitude of vibration is (Rounded to two decimal places) mm.

The 45 kg piston is supported by a spring of modulus k = 35 kN/m. A dashpot of damping coefficient 'c' = 1250 N-s/m acts in parallel with the spring. A fluctuating pressure P = 4000 sin30t in Pa acts on the piston as shown in figure below, whose top surface area is 50x10-³ m². The steady-state amplitude of vibration is (Rounded to two decimal places) mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The measurements on a mechanical vibrating system show that it has a mass of 8 kg and that the springs can be combined to give an equivalent spring of stiffness 5.4 N/mm. If the vibrating system have a dashpot attached which exerts a force of 40 N when the mass has a velocity of 1 m/s, find : 1. critical damping coefficient, 2. damping factor, 3. logarithmic decrement, and 4. ratio of two consecutive amplitudes.
Two blocks A and B, each of mass m , are supported as shown by three springs of the same constant k Block A and B are connected by a dashpot and block B is connected to the ground by two dashpots, each dashpot having the same coefficient of damping c Block A is subjected to a force of magnitude P=Pm sin wf t. Write the differential equations defining the displacements xA and xB of the two blocks from their equilibrium positions.
An undamped SDOF system with a mass of m= 20 kg and stiffness k=8000 N/m is subjected to an impact load as shown in the figure below. Assuming that the system is initially at rest, determine the displacement at t= 1.0 sec
Determine a natural frequency of vibration as a function of k₁, k₂. g and W of a spring-mass system placed on a inclined plane as shown in the figure:
The block (mass not given) is subjected to the force F = (910 sin(5.3t)) N, where t is in seconds. The spring constant (of each of the springs) is k = 347 N/m. The damping ratio is c/cc = 0.69. If the natural frequency of vibrations is fn = 1.02 Hz, what is the amplitude (in meters) of the steady-state vibrations? Choose the correct answer: a) There is not enough information to solve b) 910.000 c) 1.107 d) 2.215 e) 0.049
Question 1. A body of mass 100 kKg is suspended by a spring of stifness of 30KN/m and a dashpot of damping constant 1000 N.s/m. Vibration is excited by harmonic force ft)=80 cos (67tt) 1- Write the equation of motion of the system using Lagrange's equation. 2- Find the natural frequency and the driving frequency. 3- Write the complete solution of the vibrating system.
Determine the steady-state amplitude of the mass center of the bar of Fig P6.3 when its right end is subject to a moment M=4000sin105t N.m. Expected answer X=0.988mm
a 40kg motor is supported by four springs each of stiffness 250 N/m. The rotor is unbalanced such that the unbalance effect is equivalent to a mass of 5kg locacted 50mm from the axis of rotation. Compute the amplitude of vibration and the force transmitted to the foundation when the speed of the motor is 1000rev/min and the damping ratio is 0.15
Determine the differential equation of motion for the double pendulum shown in terms of12anduu where 12u and u are the horizontal distances of the masses from the leftmost verticalline that makes angle 1 from it. Find the natural frequencies, the ratios of the amplitudes, and thelocation of the nodes for the two modes of vibration. Assume m1=m2=m, and l1 =l2 = l=
The assembly shown below with M8x1.25 bolt/nut is subjected to an oscillating force F that changes between 0 and Fmax. Obtain the Fmax (in kN) with a saftey factor of 2, such that the amplitude of the alternating stress on the threaded section of the bolt does not exceed 48 MPa. Assume that the bolt and nut were preloaded sufficiently. The stiffness of the clamped material is evaluated as 1,017 MN/m and the stiffness of the bolt is calculated as 346 MN/m.
A four-cylinder automobile engine must be supported on three shock mounts,as shown in the picture. The engine block assembly weighs500 lbs. If the unbalanced force produced by the engine is given by200 sin 100 t lb, design three shock mounts (each stiffness k andviscous damping constant c) such that the vibration amplitudemaximum 0.1 in
A bullet of mass m= 103.4 Grams has a velocity of v0= 62 m/s just before it strikes the target of mass M=4 Kilograms, If the bullet embeds in the target, and the vibration is to be critically damped, determine the dashpot’s critical damping coefficient. The stiffness of each spring is k= 1,326 N/m