The 46-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the force F in the prop and the magnitude of the force normal to the hinge axis AB in each of the small hinges A and B.

The 46-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the force F in the prop and the magnitude of the force normal to the hinge axis AB in each of the small hinges A and B.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.7P: The linkage is made of two homogenous bars of weights shown in the figure. Determine the horizontal...

See similar textbooks

Related questions

Q: The hoist supports the 175-kg engine Determine magnitude of the force the load creates in member…

Q: Determine the magnitude and direction of the smallest force F that maintains the 30-kg package shown…

Q: The mass center G of the 1400-kg rear-engine car is located as shown in the figure. Determine the…

Q: The 43-kg homogenecus smooth sphere rests on the 36° incline A and bears against the smooth vertical…

Q: Determine the force P required to maintain the 235-kg engine in the position for which θ = 40°. The…

Q: The 54-kg homogeneous smooth sphere rests on the 28° incline A and bears against the smooth vertical…

Q: determine the force components acting on the ball-and-socket at A,the reaction at the roller b and…

A: Draw the free-body diagram of the plate. As at point A ball and socket support is present, the…

Q: Determine the magnitude of the force created in the hydraulic cylinder AD in order to hold the…

Q: The 1200-kg car is being lowered slowly onto the dock using the hoist A and winch C. Use triangle of…

Q: The 50-kg homogeneous smooth sphere rests on the 30° incline A and bears against the smooth vertical…

Q: The 75-kg cylinder A is supported by a malleable cable C at 200 and a smooth surface. Determine all…

Q: Determine the magnitude of the force which member CD exerts on the pin at C.

Q: Statics of Rigid Bodies (Equilibrium of Rigid Bodies) 3. The 25-kg rectangular access door is held…

A: The Answer is below

Q: The two steel shafts in Fig. have the same diameter and weigh 100 lb each. Neglecting friction at…

A: Consider the diagram shown below for the given system,

Q: Q2: Determine the magnitude of verntical component of reactions (Cy and Ay) and the force in the…

Q: The 40-kg homogeneous plate is suspended from four wires. Determine the tension in each wire.

A: Given data: Homogenous plate of mass 40kg To find Tension in cables TA=? TB=?…

Q: Determine the force components acting on the ball-and-socket at A , the reaction at the roller at B…

A: Given data as per the question Force at point B = 200 N Force on the side of A =350 N

Q: 3. Determine the tension in the cables in order to support the 100-kg crate in the equilibrium…

Q: The frame suppports the 400-kg load in the manner show. Neglect the weights of the memers compared…

A: For the Given frame To determine support reactions and forces in all memebers

Q: The 46-kg homogeneous smooth sphere rests on the 42° incline A and bears against the smooth vertical…

Q: The homogeneous cylinder of weight 150N is placed on an inclined surface of negligible friction. The…

Q: The 71-kg homogeneous smooth sphere rests on the (1.2/3.1) incline A and bears against the smooth…

Q: Determining the clamping force exerted on the smooth pipe at B if a force of 50N is applied to the…

A: Data given - F = 50 N

Q: The compound bar is supported by a thrust bearing at A, a slider bearing at B and the cable CD.…

Q: The 79-kg homogeneous smooth sphere rests on the ( 2.3/2.4) incline A and bears against the smooth…

Q: The 53-kg homogeneous smooth sphere rests on the 40° incline A and bears against the smooth vertical…

Q: Determine the distance d for placement of the load P for equilibrium of the smooth bar in the…

Q: The 50-kg homogeneous smooth sphere rests on the 30° incline A and bears against the smooth vertical…

A: As per given question Weight =50kg Angel=30° We have to determine contect of force A and B

Q: The skid-steer loader has a mass of 1.18 Mg, and in the position shown. The center of mass is at G1.…

Q: Determine the force P required to maintain the 200-kg engine in the position for which θ = 25°. The…

Q: 4. The block weighs 3500 kg. Find force in members AB, AC and AD.

Q: . Determine the angle ” between the table and the plane face of the hemisphere in its equilibrium…

A: Draw a free-body diagram of a given system with dimensions.

Q: Determine the magnitude of force at the pin A and in the cable BC needed to support the 560-lb load.…

Q: A basketball player weighing 200 lb hangs on the rim of the basketball hoop shown below. The…

Q: The light right-angle boom which supports the 400-kg cylinder is supported by three cables and a…

A: Consider the diagram shown below for the given figure with the reaction and tension forces as shown…

Q: The structure is made of the light bar AB and the 50-kg uniform bar CD. Compute the nagnitude of the…

A: Consider the free body diagram: Balancing forces in vertical directions:…

Q: The Shaft AB is supported by a thrust bearing at A and a slider bearing at B. Determine the force in…

Q: A puck weighs 8 lb and rests on the center of the frictionless surface of the ramp supported in…

Q: Determine the force magnitude P required to lift one end of the 250-kg crate with the lever dolly as…

A: Given data Distance from application of force to fulcrum = 1500 mm Distance from fulcrum to weight =…

Q: Determine the force acting along the axis of each of e three struts needed to support the 500-kg…

Q: For the pair of 26-lb forces applied to the handles of the crimper tool, determine the crimping…

A: tan θ = 0.90.25 = 3.6 θ = tan-1 (3.6) θ=74.475°

Q: The ramp of a ship has weight W and center of gravity at G. Determine the cable force in CD needed…

Q: A 5-lb force is applied to the handles of the vise grip. Determine the compressive force developed…

A: From the figure Free Body Diagram: E C member:tanθ= 1.753⇒θ=30.256°∴for equilibrium,∑ME=0FCD sin…

Q: Determine the contact force between the smooth 90-kg ball 8 and the horizontal bar, and the…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Chapter 3, Problem 3/073
The 46-lb rectangular access door is held in the 90° open position by the single prop CD. Determine the force F in the prop and the magnitude of the force normal to the hinge axis AB in each of
the small hinges A and B.
B
14"
48"
42"
30"
Answers:
F =
Ib
A =
Ib
В -
Ib
Click if you would like to Show Work for this question:
Open Show Work

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the force P required to (a) push; and (b) pull the 80-lb homogeneous roller over the 3-in. curb.
The pins at the end of the retaining-ring spreader fit into holes in a retaining ring. When the handgrip is squeezed, the pins spread the retaining ring, allowing its insertion or removal. Determine the spreading force P caused by the 8-lb forces applied to the handgrip.
The linkage is made of two homogenous bars of weights shown in the figure. Determine the horizontal force P required to hold the linkage in the position shown.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The 180-lb homogeneous bar is supported by a ball-and-socket joint at A and two cables attached to B. Determine the forces in the cables.
The homogeneous 20-kg door is held in the horizontal plane by a thrust hinge at O, a hinge at A, and the vertical prop BC. Determine all forces acting on the door.
The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking brake engaged, which locks the rear wheels. Find (a) the normal forces (perpendicular to the incline) acting under the front and rear pairs of wheels; and (b) the friction force (parallel to the incline) under the rear pair of wheels.
PROBLEM #1: A vertical force P = 20 lb is applied to the ends of the 2-ft cord AB and spring AC. If the spring has an unstretched length of 2 ft. Take k = 25 lb/ft. (see picture for illustration). Determine the: (a) forces (b) angle theta for equilibrium Note: Kindly show the complete step-by-step solution. Please make sure that your handwriting is understandable and the picture of the solution is clear. I will rate you with “like/upvote” after. I need the answer right away, thank you. Topics Discussed: Static of Rigid Bodies, Equilibrium of a Particle, Position Vector, Force Vector Direction, etc.
SITUATION 7: Three forces P1, P2, and P3 are acting on a semi-circular structure as shown in Fig. THA-33. Support at A is hinge and support at B is roller. Given: a = 1 m; P1 = 1.8 kN; P2 = 0.9 kN; P3 = 0.45 kN; θ = 30⁰; β = 45⁰. Calculate the resultant of the three forces (in kN). (Answer: 2.45) Calculate the vertical reaction at B (kN). (Answer: 1.06) Calculate the reaction at A. (Answer: 1.63)
A mechanism is used to apply a constant load Q to the seat in the manner illustrated. 1. Determine the following for the angle: - the lengths of LBE and LAB, in m - in degrees, the angles ? and ? 2. Compile the FBDs of members AB, FG, EBH, and GHI in their entirety. 3. Determine the forces involved in the following situations, in Newtons: - FG-member - H-pin - AB-cylinder hydraulic
Consider the force P applied at point A on the plate of the figure shown (image 1). Assuming that the weight of the plate is negligible, and that the horizontal force F, as well as the reactions Dy and Dx in the joint D balance the plate shown in the figure. Note: the x-axis is horizontal and the y-axis is vertical and both have their origin at point D. Data: P = 332N The next affirmative is true or false? If the plate had a weight of 332N (applied vertically downwards in the center of the plate), the module of F should be greater than 369.18N, so that it would still remain balanced in that position.
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.