The A-frame is being hoisted into an upright position by the vertical force of 62 lb (Figure 1) Part A Determine the moment of this force about the y axis when the frame is in the position shown. Express your answer to three significant figures and include the appropriate units. HA ? М, - Value Units Figure < 1 of 1 Submit Request Answer Provide Feedback 15 6 ft 30 6 ft

The A-frame is being hoisted into an upright position by the vertical force of 62 lb (Figure 1) Part A Determine the moment of this force about the y axis when the frame is in the position shown. Express your answer to three significant figures and include the appropriate units. HA ? М, - Value Units Figure < 1 of 1 Submit Request Answer Provide Feedback 15 6 ft 30 6 ft

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.57P: Find the stable equilibrium position of the system described in Prob. 10.56 if m = 2.06 kg.

See similar textbooks

Similar questions

The jib crane is designed for a maximum capacity of 7 kN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.7 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work.(a) What is the value of R when x = 1.9 m?(b) What is the value of R when x = 3.2 m?(c) Determine the minimum value of R and the corresponding value of x.(d) For what value of R should the pin at A be designed?
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)
When a 6 kg load is hung at point O and member AO is adjusted until it is horizontal, the angle is measured to be 35 Determine the final readings of spring scales S_{1} and S_{a} and solve for the moments they produce about each of the axes passing through A and B if member AB is measured to be 38 cm.
At the shown position, the ground reaction forces measured using a force platform are 600N in the vertical direction (Fy) and 200N in horizontal direction (Fx). The mass of the limb below the knee is 4kg with the centre of gravity at the point G. Determine the forces and moment applied to the knee joint. Draw correct free body diagram using any part of the body shown below.
How much work is done by the force in the spring when the slender rod rotates clockwise about the fixed pin support at O from the vertical position (where AB is horizontal) to the horizontal position? The spring has a stiffness of k = 125 N/m and an unstretched length of 0.15 m. Take d1= 0.29 m and d2= 0.85 m. Choose the correct answer. a) 94.9 Joule b) 99.9 Joule c) -99.9 Joule d) 0 Joule e) -94.9 Joule
Give the correct answer and clear solution of the problem1.A plate is subjected to a couple Fd , with d=20cm , as shown below left. Verify that the couple can be moved to the position shown below right, and the effect on the plate is the same, by showing that the moment about point o in both cases isM=-20F .
Determine the magnitude and direction of the angle theta of the force FAB that must be exerted on bar AB to maintain equilibrium of the system. The suspended mass is 110 kg. Neglect the size of the pulley at A and treat all pulleys as smooth. What should happen to maintain the equilibrium of the system if FAB acts with an angle theta= 0°?Consider g = 9.81 m/s2.
The left and right strings have a mass of 0.01 kg, the middle string has a mass of 0.02 kg. Both theta and beta angles are 40 degrees. Show the calculations used to determine the horizontal and vertical components of the tension forces connected to the center string.
Determine the x and y components of reaction at pin C using scalar notation. Express your answers in newtons to three significant figures separated by a comma.
Draw the free body diagram of each system
The homogeneous bars have a mass as follows: bar AC has a mass of 7 kg, bar ABhas a mass of 10 kg, and rod BD has a mass of 2 kg. In the drawn position, therod AC has an angular velocity of 4 rad/s and an angular acceleration of 2 rad/s2, both clockwise.Determine the magnitude of the moment M acting on the member AC. Give all the equations neededto solve this question without calculating it
PROBLEM 4: The boom OC is subjected to tension forces at A and C. It is known that the tension in A is 26 kN and at C is 12 kN. Unit vector CE. (ANSWER: -0.38i-0.87j+0.32k) Tension at A. (ANSWER: 13.20i-15.8j+15.8k kN VECTOR COMPONENT FORM) Moment about O due to the given forces. (ANSWER: 78.71i+0j+3.2k kN VECTOR COMPONENT FORM)