The allowable voltage drop in the figure is 5%. The underground cable is a 3-core copper conductor with PVC insulation. Find the voltage drop of line 6. Mains voltage:220/380 V %E$5 power factor everywhere: 0,8 you can use the underground cable with following Cross section :(convenient cable in suitable place) 6,25,50,95 (mm^2)

The allowable voltage drop in the figure is 5%. The underground cable is a 3-core copper conductor with PVC insulation. Find the voltage drop of line 6. Mains voltage:220/380 V %E$5 power factor everywhere: 0,8 you can use the underground cable with following Cross section :(convenient cable in suitable place) 6,25,50,95 (mm^2)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.25P: For the overhead line of configuration shown in Figure 4.33 operating at 60 Hz and a conductor...

See similar textbooks

Similar questions

For the overhead line of configuration shown in Figure 4.33 operating at 60 Hz and a conductor temperature of 700C, determine the resistance per phase, inductive reactance in ohms/mile/phase, and the current-carrying capacity of the overhead line. Each conductor is ACSR Cardinal of Table A.4.
Assume that a 7.2-kV, 60-Hz, single-conductor, belted cable has aconductor diameter of 2 cm and a lead sheath with inside diameter of4 cm. The resistivity of the insulation is 1.2 x 10^8 M-cm, and thelength of the cable is 3.5 mi. Calculate the following:(a) Total insulation resistance in megohms(b) Power loss due to leakage current flowing through insulationresistance.
Q2: Calculate the value of full-load absorbing reactive loss for 3-phase, 450 MVA, 50 Hz, 400kV, 400 mm2 overhead TL with horizontal spacing of adjacent conductors 5.5 m.
Determine the current in the neutral conductor and the current in each line conductor (i.e., IR, IB and IY) using the given information below. The powers 12 kW, 18 kW and 24 kW are the loads of a purely resistive loads which are between the yellow and blue, the red, and neutral phases respectively of a 3-Φ, four-wire system.415 V is the line voltage.
The voltage drop percentage for a panel feeder with a no continuous load of 180A, using 3/0 THWN copper conductors at 480V, three-phase, and a length of 248' is
15 A certain type of Suspension Type Insulator is used to sustain heavy tensile loads of conductors when the line has to turn a corner or stop at a dead end. Select one: True False
4 All Aluminum Conductor Cables are bare conductors Select one: True False
Please Explanation with Hand Written proper calculation with Draw. Other wise leave the Question. A overhead transmission line comprising of two parallel conductors having 1.5 cm of diameter of each. Conductor spacing is 1m. Calculate the or inductive reactance of line at 50 Hz frequency.
What is the maximum length in km for 1 phase transmission line having conductor of 0.875 square centimeter area over which 220kW at 0.8 power factor and 3500V are to be delivered? The efficiency is 80% and specific resistance is 1.825 micro cm
Q1. We have motor, motor specification as below.61 Ampare, 277V, Use EMT conduit, distance is 100f. 1. Conductor Size 2. Coduit Siz 3. Equipment Ground Conductor Size 4. Overcurrnt Protection Device Ampare Q2. We have motor, motor specification as below. 300 Ampare, 480V, 3-Phase, IMC Conduit, distance 250' 1. Conductor Size 2. Coduit Siz 3. Equipment Ground Conductor Size 4. Overcurrnt Protection Device Ampare 5. Shoul pararell conductors be used? Q3. We have motor, motor specification as below. 175 Ampare, 208V, 3-Phase, RMC Conduit, distance 165' 1. Conductor Size 2. Coduit Siz 3. Equipment Ground Conductor Size 4. Overcurrnt Protection Device Ampare
On the 1km long dc distributor above the applied voltage at point O is 200V. Lengths ??? = 100?,??? = 600? and the impedance for the conductor material per 10000m is ?? = 5 < 53.130Ω. Calculate:a. The potential at point C b. Current along section OC of the distributor
The vertical clearance of final spans of overhead service conductors above, or within _____ ft measured horizontally of platforms, projections, or surfaces that will permit personal contact shall be maintained in accordance with 230.24(B). a. 8 b. 10 c. 3 d. 6