The angular displacement of particle for one revolution is measured in radian as- 4 T O T/2 O 10 n O 5 n

Q: m3 tank contains helium at 127C and is evacuated from atmospheric pressur

A: V=6m3T=127°C=400.15KP1=101325pa...atmsP2=730mm HgHelium Molecular mass=4.0026kgm/kgmol To-Find:- a) ...

Q: Given the Cu-Zn phase diagram below, determine the amount of the phase/s present of a 75 wt% Zn -25 ...

A:

Q: A conical vessel with vertical axis has an altitude of 1 m and is filled with water. Its base, 0.60 ...

A:

Q: as az Plane C = (h k i l)

A: Given HCP crystal  We have to find the Miller Indices of Plane C

Q: Thex- and y-motions of guides A and B with right-angle slots control the curvilinear motion of the c...

A: x=25+0.74t^2 Differentiating both sides we get, Vx=1.48t at t=1.7sec Vx=2.516mm/s

Q: 4.68. For what frequencies will x3 = 0 for the system illustrated in Figure P4.68? f in k3 m1 m2 m3 ...

A: Given: value of X3=0 means there is no movement of mass m. Now writing equation of motion for mass m...

Q: Subject: Hydraulics Topic:Accelerated Liquids in Relative Equilibrium A car travelling on a horizont...

A:

Q: From the given beam, determine the moment at point B. The unit for Force is in Newton(N) and Length ...

A: For different beam supports reaction loads 1. Roller : Vertical Force 2. Hinge : Vertical Force, Hor...

Q: If = 30° and the resultant force is to be 6 kN directed along the positive y axis, determine the mag...

A: Force F1 = 4.4 kN. Force F2 = 3.1 kN. Angle θ = 45o.

Q: Lane has two pipes connected to each other that transport water because he is very thirsty. The giv...

A:

Q: STRENGTH OF MATERIALS (NO LONG EXPLANTION NEEDED. RATE WILL BE GIVEN) Two blocks of wood, 50 mm wid...

A:

Q: A lawn sprinkler (shown below from above) sprays water with an exit velocity of 2.7 m/s at än angle ...

A: according to the given details

Q: Given a parametric parabolic trajectory of x = 56t and y = 76t - 4.9t2 where x and y are measured in...

A:

Q: Find the exact and ordinary interest on Php 5,000 at 19 % for 30 days.

A: The amount of interest on a sum of money can be calculated using the formula given below as- SI=PTR1...

Q: efficiency of the heat engine ?

A: Given: A solar energy based HE which recieves 55 kJ of heatAt a rate of 1000C and rejects 45 kJ of h...

Q: 5. Determine the moment of inertia of the section in x10^6 mm^4

A:

Q: er. Data on the individual compone 30,600 W/K 26,500 W/K evaрorator condenser rofrigerntion canngity...

A: data provided D =240 mm k =0.6 w/m-kqgv= 24000 w/m3 it is isolated by Dr =440 mm k =6 w/m-kn =25 w/m...

Q: The shaded shape is supported by Cable 1 and Cable 2 in the position shown (Drawing is NOT to scale)...

A: It is asked to find the equilibrium condition and evaluate the tension in cables Weight per unit are...

Q: Read the questions carefully and answer with complete solutions and units. Use the steam tables prov...

A:

Q: How do we calculate the UTS difference

A: Given data    We are required to determine the difference in ultimate tensile strength

Q: The linkage shown rotates clockwise and at the moment shown, the block moves to the right at 5 m/s. ...

A:

Q: The truck shown is used to deliver food to aircraft. The elevated unit weighs 2400 lb vwith center o...

A:

Q: Find the elbow forces on the x and y direction.

A:

Q: Question J. fv x(t) オ Derive the equation of motion- ewe

A: For solution refer below images.

Q: Anexperimental device imparts a force of magnitude F = 67 lb to the front edge of the rim at A to si...

A:

Q: Hello, I have some diagrams I have filled out for practice that I would like to use to study for an ...

A: Diagram 1. E - relief valve A- gear pump D- rotor F- internal gear C- internal and external gear pum...

Q: Make schematic sketches of the microstructures that would be observed for conditions of very slow co...

A: (a) From the given diagram, write the phase of the composition.

Q: For the NH3/H2O cycle the following relationship give the solution flow rate per unit refrigeration ...

A: Unique: A retention refrigeration framework (ARS) is an option to the ordinary mechanical pressure f...

Q: PROBLEM 2: A support block is acted upon by two forces as shown. Knowing that the coefficients of fr...

A: To find Pmax the calculations are made by considering P as the force for impending motion of the blo...

Q: PROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position show...

A:

Q: Q3: Analyze the following figure and answer the following question (Fe-C Diagram) ? 1639 Liquid 1400...

A:

Q: 1. Determine the maximum positive bending moment in the beam in kN-m. 2. Determine the maximum shea...

A:

Q: Calculate the number of atoms in a 1.9-micron-diameter by 7.3-micron-deep cylinder in a hypothetical...

A:

Q: A 254 mm x 357 mm twin cyclinder, 4 stroke engine operates with an indicated heat efficiency pressur...

A: Answer: The friction power is 3.52 kW.  

Q: 5.For the process flow below in the yellow highlighted boxes: (i) Mark off location of mask and resi...

A: The above process is called photolithography. It is used in integrated circuit manufacturing. It use...

Q: In a furnace the fuel and air are burnt at atmospheric pressure of 1 bar temperature a 17°C. The tem...

A:

Q: Piezoresistive MEMS Accelerometer Consider the following MEMS Piezoresistive accelerometer: Piezores...

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for...

Q: at 35°C and 0.1 MPa in air-standard Otto cycles with a compression ratio of 7. The cycle reaches a m...

A: v1v2=r=7T3=Tmax=1100°C=1373kT1=35°C=308KP1=0.1Mpa=100 kpa

Q: The 97-N block B has a speed of v= 24 m/s when it is at the location shown. It slides on the incline...

A:

Q: PROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position show...

A:

Q: In a furnace the fuel and air are burnt at atmospheric pressure of 1 bar temperature and of 17°C. Th...

A: We know that fuel and air are burned in a furnace at atmospheric pressure of 1 bar and a temperature...

Q: Calculate the enthalpy, volume and entropy of 2 kg of steam at a pressure of 1.9 MPa having the dryn...

A:

Q: )Water 10°c flows down through a 53.13 deg, nclined, converging pipe section as shown. The fiow rate...

A:

Q: Two boilers one with superheater and another without superheater are delivering equal quanttes of st...

A: Given Data: The pressure of boiler, P1=P2=20 bar The pressure of the main, P3=20 bar

Q: Replace the parallel force system acting on the plate by a resultant force and specify its location ...

A:

Q: A 6m3 tank contains helium at 127C and is evacuated from atmospheric pressure to a pressure of 730 m...

A:

Q: Discussion Explain how the stationary fluid flours when it becomes in touch with heated wall. You ma...

A: Stationary Fluid flows when in contact with heated wall. This is a fluid mechanics problems related ...

Q: Write a MATLAB program that finds the sum for-25 to 5. (Increment by 5). By using (while „loop)

A:

Q: 16 kN - m 16 cm - 1m- 2 m - 2 m-

A: Solution of the question is given below

Q: 1-54 The diameters of the pistons shown in Fig. P1-54 are Di ber 3, in kPa, when the other pressures...

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.