The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of the block is 1cm. A shearing force applied to the top face produces a displacement of 0.015mm. Find the strain, stress and shearing force. Modulus of rigidity 4.5 x 10¹0 N/m².

The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of the block is 1cm. A shearing force applied to the top face produces a displacement of 0.015mm. Find the strain, stress and shearing force. Modulus of rigidity 4.5 x 10¹0 N/m².

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.15P: A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded...

See similar textbooks

Related questions

Q: the ball is kicked at an angle of 30° A) if it strikes the ground at B having coordinates (15, -9),…

A: y=-0.04x2θ=30°x=15ft,y=-9ftv=80ft/s To-Find:- a) Speed at which it is kicked b) Determine the point…

Q: Wet steam at 0.15 bar is to be compressed reversibly to form saturated water at 24 bar. Find the…

Q: A machine working on a Carnot cycle operates between -13°C and 32°C. Determine the C.O.P. when it is…

A: INTRODUCTION : The refrigerator and heat pump both are working under the Clausius statement which…

Q: An aluminium rod 20 mm in diameter is screwed at the ends and passes through a 25 mm bore steel tube…

Q: Question 1 A weight of 50 N is allowed to fall freely through a height of 130 mm onto a rigid stop…

Q: A pipe is used for energy transmission. Length and diameter of pipe are 80 m and 50 cm respectively.…

A: We have a pipe that is utilised to transport energy.The pipe's length and diameter are 80 m and 50…

Q: Why does the rod of a double-acting cylinder retract at a greater velocity than it extends for the…

A: The most widely recognized cylinder arrangement is double acting, Steering compressed liquid into…

Q: The 4 kg box shown in the figure start from rest at t = 0 in which the friction is negligible.…

A: Givent=0t=1sm=4kgF=9.81N

Q: A pressure gauge measures the reading as 29 psi. If the atmospheric pressure is 13 psi. Compute the…

Q: 3. Several blocks are resting on a simply supported beam. Determine the reaction forces. each Hack 1…

Q: The strain components for a point in a body subjected to plane strain are ɛx = 630 µɛ, ɛy = 940µɛ…

A: Consider an element subjected to normal strains εx and εy in the x and y-directions respectively and…

Q: Q2) A Carnot refrigeration cycle absorbs heat at -12°C and rejects it at 40°C. (a) Calculate the…

Q: A pipe 800 m long connects two reservoirs whose level difference is 60 m. Find the discharge in pipe…

Q: formation processes, friction and associated forces can account for a substantial percentage of the…

A: The answer is given in next step:

Q: The hollow shaft used in the system has the following conditions: Outer Ø:110 mmØ Allowable…

A: Shear stress-induced in the shaft at any location (r) from the center is given by,Where, r = Radial…

Q: A wind tunnel is considered to be a steady-state operation, the system receives one hundred fifty…

Q: at is the angle of incidence of the radio wave signal as it moves from air to glass (relative…

A: The angle of incidence of radio wave (I) = 600 Critical electron density (NCR.) = 60X109/cm3 =…

Q: Consider an apartment in a tower block as a cube of side L = 7.26 m. Since this apartment is…

Q: The n ve. f graph below is for a newly discovered material. Please note that the metric prefie…

A: 1)The pure solid substance will be absorbing heat from 140 oC to 160 oC. Here phase change does not…

Q: b) What is the measurement resolution, in degrees of arc, of an incremental optical angle encoder…

A: degree of arc of an incremental optical angle

Q: Required information Two solid steel shafts (G= 77.2 GPa) are connected to a coupling disk B and to…

Q: 8,038 N m) flows through the pipeline (Figure C2). . Gasoline (specific weight y Calculate the flow…

Q: particle is moving along a straight line with a = (12t - 3t^0.5) ft/s^2, where t is in seconds.…

Q: Consider the second order ordinary differential equation: d²x(t) dt2 dx(t) + 12- dt + 8x(t) = 8u(t)…

Q: Why should the overhang distance of a lathe tool be minimized? What occurs if a lathe tool is set…

Q: Determine the following statement that is true regarding Mohr's Circle. O Mohr's Circle contains all…

A: Mohr’s circle It is basically a two-dimensional graphical representation of the principal stress. On…

Q: 1. 4000L/hr of distillates are cooled from 21 to 12 degrees Celsius, and wax is separated 12% by…

Q: 3. A bronze bar having a cross-sectional, area of 200 mm? carries the axial loads shown in the…

Q: Multi-evaporator system with individual multiple expansion compressors and valves

A: ME-VCS (multi-evaporator vapour compression systems) are used to cool numerous zones. The…

Q: 20 kN 40 kN m B D C4 - 4 m- 2m2 m-- 20 kN FIG. P4.25

Q: To mixer design, estimate the power requirement (kw/m³), agitation type for homogenous reaction…

Q: 200 kg of pork is to be cooled from 20 to 5 C, then frozen and cooled to -20 C. The moisture content…

Q: A pitot tube directed into a water stream having velocity 2.3 m/sec. Its gauge difference of 30 cm…

A: It is a device used for the measuring of flow. The velocity of flow at a particular point is reduced…

Q: a new machine. The n conthoOus use and repair rate of 0.10 per day Compute the machine inherent…

A: Given Repair rate, R = 0.1 Failure rate, F = 0.021 Find Machine availability, A

Q: Consider the arrangement of three wind turbines in the following schematic in which wind turbine C…

A: Solution: Given Data: To Find: (a) udef(b) VC

Q: With velocity of 10 m/s in the 347 mm diameter pipe in the figure shown, determine the discharge in…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

Q: Discbrake friction linings are sometimes called brake The ratio of the force required to slide one…

A: Given questions are related to IC engines and Machine design [Note : According to…

Q: A rectangular plate with a V-notch is shown in Fig. 2.29. Model the plate using triangular elements…

A: Given : To find : Model the plate using triangular elements

Q: The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness…

A: Given t=30mm P=2.5MPa D=8m=8000mm n=900 d=20mm

Q: If the motorcycle leaves the ramp traveling at 136 ft/s, determine the height h ramp B must have so…

Q: A 100 x 300 mm ammonia compressor with a compression efficiency of 82% operates with a suction…

A: Given, bore of the compressor , d = 100 mm stroke of the compressor , L = 200mm Condenser pressure…

Q: For the area shown below defined by the two curves, to find ly by integration you use a dA element…

Q: An annealed-steel specimen has a 0.750 in. diameter and a 12.000 in. gag length. Maximum load is…

A: Disclaimer: Since you have posted multiple questions we will solve the first question for you. If…

Q: 2. The hollow shaft used in the system has the following conditions: B Outer Ø: 110 mm Ø Allowable…

A: Shear stress-induced in the shaft at any location (r) from the center is given by,= = 11/12Where, r…

Q: 1. An industrial company operates a steam power plant with reheat and regeneration. The steam enters…

Q: For the beam with shown loading, show that the equation of the elastic curve is Wo 7w,L3 + x3 y = EI…

Q: The ball of mass m is guided along the vertical circular path r = 4cos(0)meters using the arm OA. If…

Q: An 8-cm diameter pipe is used for a pipeline for moving oil from one container to another at a…

Q: 144.2. A 600-lb block slides down an incline having a slope of 4 vertical to 3 horizontal. It starts…

A: 14-4.2 The free-body diagram of the block is as shown below,

Question

**Need asap pls. Thank you.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of the block is 1cm. A shearing force applied to the top face produces a displacement of 0.015mm. Find the strain, stress and shearing force. Modulus of rigidity 4.5 x 10¹0 N/m².
A bar of 6-mm in diameter is only allowed to decrease at a maximum of 3.96% of its total length. What is the maximum force (Newtons) that can be applied? Consider the shear modulus = 602 MPa, and the Poisson's ratio as 0.20. Express your answer in three decimal places.
If the ultimate shear strength of a steel plate is 42,000psi. What is the force necessary to puncha 0.75in diameter hole in a 0.625in thick plate
A plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of the bars is 80. If the allowable shear strain in the plastic is 0.014 radian, what is the minimum permissible length of the bar in mm?
If the shear stress in a material is 20 MPa and the corresponding shear strain is 0.0005, calculate the shear modulus of the material.
A rectangular plate with dimensions 200 mm x 300 mm is subjected to a simple shear stress of 60MPa. Determine the magnitude and direction of the shear force required to produce this stress.
A rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains.
a) The deformations for a material element in plane deformation (see figure 1) are the following: εxx = 480 × 10−6, εyy = −450 × 10−6 and γxy = −350 × 10−6. Using Mohr's Circle, determine the principal strains and maximum shear strains, and make an appropriately oriented sketch. b) And solve the exercise for the following data: εxx = −1120 × 10−6, εyy = −430 × 10−6, and γxy = 780 × 10−6.
2. A rectangular key was used in a pulley connected to a line shaft at 23 HP and 10 rps. If shearing of key is 230 Mpa, determine the force acting on key length if key width is one-fourth of shaft diameter and key length of one inch.
An aluminum thin‐walled tube of hollow rectangular cross‐section, Figure 1,is subjected to a torque of magnitude, T = 15360 N.m. If the tube lengthis, L = 1 m , and the shear modulus of aluminum is, G = 28 GPa.1. Determine the total angle of twist of the one‐meter long tube.2. Determine the shear stresses on the walls of the tube cross‐section.Where does the maximum shear stress occur?