Wet steam at 0.15 bar is to be compressed reversibly to form saturated water at 24 bar. Find the entropy, quality and enthalpy of the original wet s(isentropic compression). Find the entropy, quality and enthalpy of the emerging wet steam taking the isentropic efficiency of the compressor as 80Maximum marks will be awarded as follows:a) A succinct problem statementb) A plant diagramc) A T-S diagram showing the actual and isentropic compressionsd) A list of assumptions made to solve the questione) A list of physical laws used to solve the questionf) Calculations1. Find the entropy, quality and enthalpy of the original wet steam for an isentropic compression (9 marks)2. Find the entropy, quality and enthalpy of the emerging wet steam taking the isentropic efficiency of the compressor as 80% (9 marks)g) Discussion , Enter your numerical values below:1.1 Find the entropy of the original wet steam for an isentropic compression. Give your answer in kJ/kg.K to three decimal places.1.2 Find the quality of the original wet steam for an isentropic compression. Give your answer in percentage to two decimal places.1.3 Find the enthalpy of the original wet steam for an isentropic compression. Give your answer in kJ/kg to one decimal place.2.1 Taking the isentropic efficiency of the compressor as 80%, find the entropy of the emerging wet steam. Give your answer in kJ/kg.K to three decimal places2.2 Taking the isentropic efficiency of the compressor as 80%, find the quality of the emerging wet steam. Give your answer in percentage to two decimalplaces.2.3 Taking the isentropic efficiency of the compressor as 80%, find the enthalpy of the emerging wet steam. Give your answer in kJ/kg to one decimal place.

Answered: Image /qna-images/answer/4a34bb49-e9e7-44b5-8455-41b28c7253f5.jpg

Wet steam at 0.15 bar is to be compressed reversibly to form saturated water at 24 bar. Find the entropy, quality and enthalpy of the original wet (isentropic compression). Find the entropy, quality and enthalpy of the emerging wet steam taking the isentropic efficiency of the compressor as Maximum marks will be awarded as follows: a) A succinct problem statement ( b) A plant diagram c) A T-S diagram showing the actual and isentropic compressions d) A list of assumptions made to solve the question e) A list of physical laws used to solve the question f) Calculations ( 1. Find the entropy, quality and enthalpy of the original wet steam for an isentropic compression (9 marks) 2. Find the entropy, quality and enthalpy of the emerging wet steam taking the isentropic efficiency of the compressor as 80% (9 marks)

Wet steam at 0.15 bar is to be compressed reversibly to form saturated water at 24 bar. Find the entropy, quality and enthalpy of the original wet (isentropic compression). Find the entropy, quality and enthalpy of the emerging wet steam taking the isentropic efficiency of the compressor as Maximum marks will be awarded as follows: a) A succinct problem statement ( b) A plant diagram c) A T-S diagram showing the actual and isentropic compressions d) A list of assumptions made to solve the question e) A list of physical laws used to solve the question f) Calculations ( 1. Find the entropy, quality and enthalpy of the original wet steam for an isentropic compression (9 marks) 2. Find the entropy, quality and enthalpy of the emerging wet steam taking the isentropic efficiency of the compressor as 80% (9 marks)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
N2 gas enters a turbine at P = 275.79 kPa, 130°F and leaves at 101.353 kPa and 80°F. How much heat is lost if 8 Btu of work per lbm of nitrogen is produced? Cp nitrogen = 3.5R where R = 1.9859 Btu/lbmol-oR. a. 10.24 Btu per lbm of the gas b. 4.41 Btu per lbm of the gas c. None of the choices d. 3.98 Btu per lbm of the gas
A certain gas with cP= 0.530 Btu/lbm-R and R = 100 ft-lbf/ lbm-R expands from 10 cu.ft and 60 F to 30 cu.ft. while pressure remains constant at 20 psia. Compute a) T2 in oF b) dH c) dU d) dS e) For internally reversible nonflow process, what is Work?
I need help with a review porblem I cannot solve! thank you Steam enters an adiabatic turbine at 4 MPa, 800K and exits at 8 kPa, 90% quality. Assuming steady state, steady flow conditions, determine: a) The power output of the turbine (MW) if the mass flow rate is 63kg/s. b)The volumetric flow rate at the inlet (m3/s).
Can you provide the step-by-step solution how to get the answers? Steam flows adiabatically through a nozzle from 1517 KPaa, 290 °C, to 965 KPaa. Sketch the pV and Ts diagram and for m=454 gm/sec, Determine delta s, delta u, delta v, delta h, work nonflow and work steady flow. the first three (delta s, delta u, delta v, delta h) were already answered. Can you continue the bold part
Can you provide the step by step solution how to get the answers? Steam flows adiabatically through a nozzle from 1517 KPaa, 290 °C, to 965 KPaa. Sketch the pV and Ts diagram and for m=454 gm/sec, Detemine delta s, delta u, delta v, delta h, work nonflow and work steady flow.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
Write legibly so i can understand 3. The turbine section of a Brayton cycle gas turbine receives hot compressed air at 150 psia and 2100 o R, expands it to 15 psia and develops a gross output of 15,000 HP. Air enters the compressor at 500 R. Determine: a) Mass flow rate (lb m/s ), b) power to drive compressor (HP), c)Net power output, d.) thermal efficiency, e) mean effective pressure (psia)
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Here are the questions to be answered: 1. Why is the value of Wexp 0? (Explain) 2. Given the above values, can you calculate the Wflow? (Yes/No)
DRAW THE PV TS DIAGRAMS FOR BOTH PROBLEMS 1. During a reversible process 320 kJ/s of heat are given off by 1.5 kg m /s of a certain gas while its temperature remains constant at 27.7 o C. For this gas c p = 2.232 kJ/kg m - o K and k = 1.303. The initial pressure is 590 kPaa. Find a) final volume, b) work non flow (kJ/s), c) ∆S (kJ/ o K -s) 2. An ideal compressor compresses 12 kg/min of air isothermally from 99 kPaa and a specific volume of 0.81 m 3 /kg m to a final pressure of 600 kPaa. Determine a) Power (kW) required to drive the compressor, b) change in entropy (kJ/ O K), c) heat transferred. (PLS SHOW COMPLETE SOLUTION AND WRITE PROPERLY) (PLEASE ANSWER BOTH QUESTIONS PLEASE)
A turbine, operating under steady- flow conditions, reccives 1000 kg/min of stcam. At the inlet, the pressure is 30 bar, the temperature is 400°C, the velocity At the exit, the pressure is 0.7 bar, the quality is (100%), and the velocity is 100 m/s. If the turbine produced a power output of 9300 KW. By using the energy balance of open system with sutable tables, answer the following: (a) What are the main assumptions ? (b) Calculate dh, AKe ? (c) Calculate the rate of heat transfer between the turbine and surroundings, in kW.
Q22(i) Construct the flow chart (diagram) and compute the total heat required to convert 900 g of ice at –30°C to steam at 145 °C. (Cice = 2090 J/kg.°C, Cwater = 4186 J/kg.°C, Csteam = 2010 J/kg.°C, Lf = 3.33 × 105 J/kg, Lv = 2.26 × 106 J/kg.)