The assembly is subjected to a torque of (a) T = 90 Nm (b) T = 200 Nm. If the Factor of safety for the assembly is 2.0 and shear yield stress is 112 MPa, determine the radius of the fillets that can be used o transmit the torque. mm IN-m

The assembly is subjected to a torque of (a) T = 90 Nm (b) T = 200 Nm. If the Factor of safety for the assembly is 2.0 and shear yield stress is 112 MPa, determine the radius of the fillets that can be used o transmit the torque. mm IN-m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Determine the maximum shear stress in the solid shaft. The diameter of the shaft is 1 in. Assume the…

A: Given-Data:- Diameter of shaft=1inch No Friction is assumed To-Find:- Maximum Shear Stress

Q: The 6061-T6 aluminum solid shaft is subjected to the loading shown. (a) Determine the maximum shear…

Q: The two solid steel shafts are connected by gears C and F and supported by smooth bearings at B, D,…

Q: The gear motor can develop 2 hp when it turns at 150 rev>min. If the allowable shear stress for…

A: Given data: The gear motor can develop a power p =2 hp. The R.P.M of the motor is ω =150 rev/min.…

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

Q: The shaft consists of three concentric tubes, each made from the same material and having the inner…

A: Given data: The magnitude of the torque acting on the shaft, T = 800 N·m. Calculate the polar…

Q: The five-bolt connection must support an applied load of P = 1500 lb. If the average shear stress in…

Q: The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the…

A: Given data: The allowable shear stress in the magnesium bar is τmg=45 MPa The allowable shear stress…

Q: The 60-mm diameter solid aluminumshaft has three pulleys A, Band Cmounted on it. Assume T= 1669…

A: Given data: Shaft diameter, D=0.06 m

Q: If the material is machine steel having a yield stress of sY = 700 MPa, determine the factor of…

A: To understand that there is no shear stress acting on the body. Its pure case of normal stress so…

Q: The gear motor can develop 3 hp when it turns at 150 rev>min. If the allowable shear stress for…

A: The power is given as, The angular velocity of the rotation is written as,

Q: The steel shaft is made from two segments: AC has a diameter of 12 mm, and CB has a diameter of 25…

Q: 1992 steel sha has à diámétér and is fixed its ends A ánd B. If it is subjected to the torques…

A: Given - Data:- A992 Steel Shaft E=75GPa Diameter(D)=60mm=0.06m Torques = 600 and 300 N-m To Find:-…

Q: A power source at C actuates valves at A and B through a long round steel control rod. A torque of…

Q: The solid steel shaft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It…

A: Given , diameter of shaft=d=25mm=25x10-3m Revolutions of the shaft n=50 rev/sec…

Q: PI0-2. Determine the internal torque at cach section and show the shear stress on differential…

A: Consider the torque diagram shown below for the given shaft.

Q: The assembly is used to support the distributed load of w=500 lb/ft. determine effort normal in bar…

A: Given Force = 500 lb/ft Bar diameter = 0.4 in Bolt diameter = 0.3 in To find Normal stress in bar…

Q: The rod has a diameter of 1 in. and a weight of 10 lb>ft. Determine the maximum torsional stress…

A: diameter of rod (d) = 1 in. weight of rod (w) = 10 lb-ft the FBD of the cut segment of the rod is…

Q: The bearings at A and B exert only x and z components of force on the steel shaft. Determine the…

A: Here,RAX+RBX=5KN AndRBX×750-5×150=0⇒RBX=1KN=1000NSo,RAX=7.5-RBX⇒RA=(5-1)=4 KN=4000NNow,Bending…

Q: The 304-stainless-steel cylinder has an inner diameter of 4 in. and a wall thickness of 0.1 in. O…

Q: 250 mm D 750 mm 120 N•m The two shafts are made of A-36 steel. Each has a diameter of 25 mm, and…

Q: The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. If P = 5…

Q: The five-bolt connection must support an applied load of P = 3800 lb. If the average shear stress in…

Q: The shaft consists of a solid segment AB and a hollow segment BC, which are rigidly joined by the…

A: Given for solid part D=80 mm Cs=80/2=40mm Max. shear stress for solid rod is given…

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

A: Given data, DAC = Diameter of AC segment = 50 mm DCB = Diameter of CB segment = 100 mm TD = Torque…

Q: The steel shaft is made from two segments: AC has a diameter of 50 mm, and CB has a diameter of 100…

Q: Q1- Prove that the shear stress of circular shaft under pure torsion is Tr %3D Tmax Ip

A: Given Circular shaft To find ζmaax=TrIP

Q: The solid circular shaft is subjected to an internal torque of T = 5 kN # m. Determine the shear…

Q: The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If a torque of T = 5 kN # m is…

A: Given data as per question Torque transmitted = 5 KN.m Length of shaft = 900 mm for Mg rod value of…

Q: The tube is made of C86100 bronze and has a rectangular cross section asshown in Figure. If it is…

A: The FBD of the system is as follows:

Q: Problem #1: The steel shaft is made of two segments, AC has a diameter of 12 mm and CB has a…

A: Given data: dAC=12 mmdCB=25 mmT=750 N.mG=75 GPa Need to determine the maximum shear stress.

Q: A torque of 2 kip # in. is applied to the tube. If the wall thickness is 0.1 in., determine the…

A: Torque T = 2 kip in = 0.16 kip ft thickness t = 0.1 in rm = (2 + 1.9)/2 in =1.95 in Am = π4 rm2=…

Q: The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is subjected to the…

A: Given data: Outer diameter of shaft = 100 mm The inner diameter of the shaft =…

Q: If the eyebolt is made of a material having a yield stress of a, = 150 MPa, determine the minimum…

A: Given Data Yield stress of eye bolt is ; σy=150 MPa Factor of safety is : F·S=2.5 Force is F=20…

Q: The shaft is made of L2 tool steel, has a diameter of 40 mm, and is fixed at its ends A and B. If…

Q: The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. If the allowable shear stresses for…

A: Given Shear stress of magnesium = 45 MPa = 45 × 106 Pa Shear stress of steel = 75 MPa = 75 × 106 Pa…

Q: Q5/ The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is subjected to…

A: From the compatibility equation, the torque in the shafts AC and BC can be determined as,

Q: If the solid shaft AB to which the valve handle is attached is made of C83400 red brass and has a…

Q: The shaft is made of red brass C83400 and has an elliptical cross section. If it is subjected to the…

A: The Torsion formulae in case of shafts with elliptical section gets modified and are as mentioned…

Q: QUESTION 1. Determine the constant thickness t of the square shaped tube if the average shear stress…

A: Given data: The average shear stress is; ? = 90 MPa. The magnitude of the torque is; T = 3 kNm. The…

Q: A flanged bolt coupling has eight 10-mm diameter steel bolts on 600 mm diameter bolt circle and six…

Q: The device shown is used to mix soils in order to provide in-sity stabilization. If the mixer is…

Q: The steel step shaft has allowable shear stress of tallow = 8 MPa. If the transition between the…

A: Given data: Allowable shear stress, τallow = 8 MPa. Diameter of the larger cross-section, D = 50…

Q: The gear motor can develop 1 10 hp when it turns at 80 rev>min. If the allowable shear stress for…

Q: Q1 The power of motor is (15)H.P rotating to (1800) rpm design the key which to located on the shaft…

A: Given Data: Power P=15 H.P=11185.85 W=11.185 KW 1 H.P=745.7 Watts Speed N=1800 rpm Diameter d=60 mm…

Q: FI0-2 The hollow circular shaft is subjected to an internal torque of T = 10KN-m. Determine the…

A: giventorque T=10kN-m=10×106 Nmminternal diameter d=40mmexternal diameter D=60mm

Q: If the material is machine steel having a yield stress of sY = 750 MPa, determine the factor of…

Question

The assembly is subjected to a torque of (a) T = 90 Nm (b) T = 200 Nm. If the Factor of safety for the
assembly is 2.0 and shear yield stress is 112 MPa, determine the radius of the fillets that can be used
to transmit the torque.
mm
IN-m
b mm
מאז
2.0
1.9
18
1.7
16
Djd - 25
20
K1S
14
1.67
13
1.25
12
1.0
0.00
0.05
0.10
0.15 0.20 0.25 0.30

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and 8-12mm diameter on a concentric bolt circle 260mm in diameter. What torque can be applied without exceeding a shearing stress of 60MPa in the bolts? B) Determine the number of 10mm steel bolts that must be used on the 320mm bolt circle of the coupling to increase the torque capacity by 6KN-m.
Two sections of steel drill pipe, joined by boltedflange plates at B, are being tested to assess the adequacyof both the pipes. In the test, the pipe structureis fixed at A, a concentrated torque of 500 kN ? m isapplied at x = 0.5 m, and uniformly distributed torqueintensity t0 = 250 kN . m/m is applied on pipe BC.Both pipes have the same inner diameter d = 200 mm.Pipe AB has thickness tAB =15 mm, while pipe BChas thickness tBC =12 mm. Find the maximum shearstress and maximum twist of the pipe and their locationsalong the pipe. Assume G = 75 GPa.
The mean dimensions of the cross-section of the leading edge and torsion box of an airplane wing can be approximated as shown. If the wing is made of 2014-T6 (G = 19 GPa) aluminum alloy having an allowable shear stress of Tallow = 158 MPa, and the wall thickness is 12 mm. Determine the maximum allowable torque and the corresponding angle of twist per meter length of the wing.
The Am1004-T61 magnesium tube is bonded to the A-36 steel rod. the allowable shear stresses for the magnesium and steel sre Tallow mg =45Mpa ve Tallow st=72MPa, respectively. The shear modulus of elasticity for Am1004-T61magnesium alloy is 18Gpa and for A-36 steel is 75Gpa. a)Determine the maximum allowable torque that can be applied at A. b)Find the corresponding angle of twist of end A.
The 304-stainless-steel cylinder has an inner diameter of 4 in. and a wall thickness of 0.1 in. If it is subjected to an internal pressure of p = 80 psi, axial load of 500 lb, and a torque of 70 lb · ft, determine if yielding occurs according to the maximum shear stress theory.
Internal loadings at a critical section along a steel drive shaft are given. If theyield stress under tension and shear are S_y = 800 MPa, respectively, determine the maximum length of the shaft using the maximum-shear-stress theory (Tresca yield theory) in a way that the shaft does not fail neither at A nor at B. （DON'T COPY OTHER ANSWER)
The A-36 hollow steel shaft is 2 m long and has an outer diameter of 40 mm. When it is rotating at 80 rad>s, it transmits 32 kW of power from the engine E to the generator G. Determine the smallest thickness of the shaft if the allowable shear stress is tallow = 140 MPa and the shaft is restricted not to twist more than 0.05 rad.
Would you kindly answer this question. If the shaft must have one uniform diameter, determine the required minimum diameter of the shaft if the normal yield stress in the composite shaft must not exceed 450 MPa with a factor of safety equal to 1.8.
If the shaft is made of red brass C83400 copper with an allowable shear stress of ?allow = 20 MPa, determine the maximum allowable torques T1 and T2 that can be applied on A and B. Also, find the corresponding angle of twist of end A. Set L = 0.75 m "Mechanics of Materials, Hibbeler"
Determine the diameter of a taper pin for use to fix a lever to a shaft, if it is to transmit a maximum torque of 700 in-lbs. The shaft diameter is 2 inches and the material allowable stress is 15000 psi. Use factor of safety of 2. a.) 5.2 mm b.) 7.0 mm c.) 7.2 mm d.) 6.2 mm
A flanged bolt coupling consists of nine ½ -in diameter bolts equally spaced around a bolt circle 15 inches in diameter. Determine the torque capacity of the coupling if the shear stress in the bolt is limited to 5000 psi. Answer: T = 11.04 kip-ft
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.