The assembly supports a uniform distributed load = 1.65 kN/m as shown. Part A Determine the resultant internal loadings at cross sections at point on the assembly. Express your answers, separated by commas, to four significant figures. V AZO NE=, VE =, ME = Submit Request Answer Part B Determine the resultant internal loadings at cross sections at point F on the assembly. Express your answers, separated by commas, to four significant figures. Np. Vp, Mp= Submit Provide Feedback VO ALO 63 12 Request Answer 1? kN, KN, KN-m kN, KN, KN-m D E 0.5 m 0.5 m 0.5 m B Im -1.5 m 2 m

The assembly supports a uniform distributed load = 1.65 kN/m as shown. Part A Determine the resultant internal loadings at cross sections at point on the assembly. Express your answers, separated by commas, to four significant figures. V AZO NE=, VE =, ME = Submit Request Answer Part B Determine the resultant internal loadings at cross sections at point F on the assembly. Express your answers, separated by commas, to four significant figures. Np. Vp, Mp= Submit Provide Feedback VO ALO 63 12 Request Answer 1? kN, KN, KN-m kN, KN, KN-m D E 0.5 m 0.5 m 0.5 m B Im -1.5 m 2 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 344 mm from the centroid of the rivet group. Assume a = 165 mm Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPa
The 1900-NN load is applied along the centroidal axis of the member. (Figure 1) Determine the magnitude of the resultant internal normal force in the member section a-a. Express your answer to three significant figures and include the appropriate units. 2) Determine the magnitude of the resultant internal shear force in the member section a-a. Express your answer to three significant figures and include the appropriate units.
Use 32 in2 and 48 in2 cross-sectional areas for tensile and compressive members, respectively. Determine the axial stress in member CH in psi. (Numerical absolute answer only without units in 3 decimal places)
Applied mechanics: An undersea research vehicle has a spherical hull of 1m radius and a 40mm thickness. The hull is constructed of high strength alloy steel having a yield point of 700 MPa. Neglecting the adverse effect of entrance ports cut into the hull determine the depth the vessel may be submerged to set up a stress equal to that of the yield point. Relative density of sea water = 1.023
The member consists of the steel rod AB that is screwed into the end of the bronze rod Find the largest value of P that meets the following design criteria: (a) the overall length of the member is not to change by more than 3 mm; and (b) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze.
Rank the normal stress in each section of the bar. Rank the values of normal stress from largest (largest tensile stress) to smallest (largest compressive stress). Use AB for segment AB, BC for segment BC, and CD for segment CD.
The cross section of the CD part of the crane boom in the picture is a standard 50x150mm2. Determine the normal stress at the center of the part. Use exact values in the calculation, just round the answers! The mass of the load is: mk=59033 kg
The bearings at A and D exert only y and z components of force on the shaft as shown in Fig 7. Determine the smallest diameter of the shaft using maximum shear stress hypothesis theory if the allowable stress is 100 MPa.
The steel bar has the original dimensions shown in the figure. It is subjected to an axial load of 50 kN. Est=203 GPa, vst=0.27. Determine the change in its length. Express your answer to three significant figures and include appropriate units.
The following figure shows the critical position of a crane that supports 2.5 Tons of load by means of a chain. You are delegated the responsibility of building a crane with similar geometric characteristics and load capacity. The diagram of free body of the crane arm can be redrawn as follows. (check the attached image "fbd") Assuming that the crane arm will be made of steel with yield stress sigmaY =220 MPa and that you must consider a safety factor of F.S.=1.5, propose a profile from the following catalog for the manufacture of the crane arm. Ignore the effects of shear forces on this element. On the other hand, it is very important that you consider the effects of axial loads. Commercial profiles for arm construction. (Check image "profiles")
The assembly consists of three disks A, B , and C that are used to support the load of P. The load P(kN) = 328 . The thickness of block B t1(mm)=26 . The thickness of block t2(mm)=13 . The allowable bearing stress ()b (MPa) = 213 . The allowable shear stress Tallow (MPa) = 71 =Bear area of disk A =Bear area of disk B
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 20 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 5 kips, R = 20 kips and S = 28 kips. Calculate F1, F2, F3 and..