The ball is truncated at its ends and is used to support the bearing load P. The modulus of elasticity for the material is E. P 2. Part A Determine the decrease in the ball's height when the load is applied. Express your answer as an expression in terms of the variables P, r, and E and any necessary constants.

The ball is truncated at its ends and is used to support the bearing load P. The modulus of elasticity for the material is E. P 2. Part A Determine the decrease in the ball's height when the load is applied. Express your answer as an expression in terms of the variables P, r, and E and any necessary constants.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.55P: Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free...

See similar textbooks

Similar questions

A 10-mm-diameter rod has a modulus of elasticity of E = 100GPa. If it is 4 m long and subjected to an axial tensile load of 6 kN, determine its elongation. Assume linear elastic behavior.
Determine the maximum allowable eccentric load P that can be applied to the wood column. The column is fixed at its base and free at its top. Use the NFPA equations of Sec. 13.6 and Eq. 13–30.
A 20-ft-long column is made of aluminum alloy 2014-T6. If it is pinned at its top and bottom, and a compressive load P is applied at point A, determine the maximum allowable magnitude of P using the equations of Sec. 13.6 and Eq. 13–30.
The rigid beam rests in the horizontal position on two 2014-T6 aluminum cylinders having the unloaded lengths shown. If each cylinder has a diameter of 30 mm, determine the placement x of the applied 80-kN load so that the beam remains horizontal. What is the new diameter of cylinder A after the load is applied? nal = 0.35.
The load is supported by the four stainless steels wires that are connected to the rigid members AB and DC. The members were originally horizontal, and each wire has a cross-sectional area of 16mm2. Given that E= 200Gpa for all the steel wires. a) Draw Freee Body Diagram(FBD) of each rigid member. b) Determine the angle of tilt of each member after the 2250N load is applied
The column consists of a rigid member that is pinned at its bottom and attached to a spring at its top. If the spring is unstretched when the column is in the vertical position, determine the critical load that can be placed on the column.
A steel column has a length of 9 m and is pinned at its top and bottom. If the cross-sectional area has the dimensions shown, determine the critical load. Est = 200 GPa, sY = 250 MPa.
13.62 A bumper made of a hard spring is to stop a 30ton gondala car which is traveling at 4ft/s as shown. Such a spring developes a restoring force F=100x+12x^3 kips when it si compressed by an amount of x ft. Determine the maximum deflection of the bumper.
A large tower is to be supported by a series of steel wires; it is estimated that the load on each wire will be 13,300 N (3000 lbf). Determine the minimum required wire diameter, assuming a factor of safety of 2.0 and a yield strength of 860 MPa (125,000 psi) for the steel
A large water tank that has a capacity to carry 20,000 liters is to be supported by four cylindrical posts. These four support posts are made of plain carbon (1045) steels with the yield and tensile strengths of 310 MPa and 565 MPa, respectively. Determine the minimum required diameter of the post assuming a factor of safety of 5.
The 10-ft wooden rectangular column has the dimensions shown. Determine the critical load if the ends are assumed to be pin connected. Ew = 1.6(103) ksi, sY = 5 ksi.
A steel column has a length of 5 m and is free at one end and fixed at the other end. If the cross-sectional area has the dimensions shown, determine the critical load Est = 200 GPa, sY = 360 MPa.