The bar AB slides so that its bottom point A has a velocity of 400 mm/s to the left along the horizontal plane. What is the angular the angular velocity and acceleration of the bar in the phase shown. Use two methods: analytical and the instantaneous center methods.

The bar AB slides so that its bottom point A has a velocity of 400 mm/s to the left along the horizontal plane. What is the angular the angular velocity and acceleration of the bar in the phase shown. Use two methods: analytical and the instantaneous center methods.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A shaft rotating with 19 rev/s is uniformly accelerated at 0.4 rad/s? for 6 seconds. It then rotates…

A: Given, N1=19 rev/sα1=0.4 rad/s2t1=6 sect2=9 sect3=15 sec

Q: The wheel in the figure rotates clockwise with a constant angular velocity of 120 rpm. The pin D is…

A: Solution Convert the angular velocity of wheel from rev/min to rad/s.ω=2πN60φ=2π×12060 =4π rad/s

Q: Figure2 shows the rod AB is subjected to speed decreasing of 2 m/s and velocity of v in unit m/s.…

Q: It moves 4 horizontally and 6 vertically. θ2 (⁰) = 20⁰ ω2 = 75 rad/s (+)Find the speed of limbs 4…

Q: 0.3 m B (0) AB 12 rad/s 0.6 m 30° II IV D The velocity at point B is 3m/s towards the left. a. What…

A: given; velocity of B towards left (VB)=3m/sAB=0.3mBD=0.6mθ=300

Q: The disk rotates with angular speed -2 rad/s. The small ball A is moving along the radial slot with…

Q: Link AB rotates through a limited range of the angle B and its end A causes the slotted link AC to…

A: GIVEN:AB=150mmAC=rCB=150mmangle ACB=θangle CBA=β=53'angular velocity of rod AB=β˙=1.3rad/secfind the…

Q: For the mechanism shown, R= 0.45 m, 0 the cam rotates with angular velocity of acceleration of-20…

A: 880.9

Q: A wheel is rolling without slipping with the center velocity is 5 m/s to the left as shown in Figure…

A: 4.3

Q: Rod DC rotates counterclockwise with angular velocity N of 2 rad/s. Determine: The angular velocity…

Q: In the figure shown, if wA=500rpm, solve for (a) the angular velocity of disk C (in rad/s) (b) the…

Q: The gear is connected to Rack C in the picture shown below. The rope B is attached to the gear at…

A: given:

Q: For items 4-5, consider the following: At the instant shown, drum D rotates at a constant angular…

A: Given: The angular velocity of drum, ω = 10 rad/s (CCW) The angular velocity of rod AB, ωAB = 5…

Q: figure. The saw blade slides along the horizon the flywheel at a consta 60 rev/min, determine for…

A: Hecksaw Machine

Q: If we had the velocity and acceleration of the point A , find the Angular velocity and angular…

Q: or the slider-crank mechanism shown, link (2) rotates with an angular velocity of 1.0 rad/sec CW.…

Q: During a manufacturing operation a tray of product is oscillated under a water spray by the action…

A: Given:θ=15o CωAB=0.086 rad/s anti-clockwise

Q: Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Vince Carlo is a world-renowned…

Q: a snowmobile is originally at the point with the position vector 29m at 95degrees counterclockwise…

A: Given data as per question Position = 29 m at 950 Velocity = 4.5 at 400 Acceleration = 1..9 at 2000…

Q: QI. Use the graphical method only, find the velocity of the piston for the system shown below and…

A: Graphical Method Means We Will Use Instantaneous Center Method. Number Of Instantaneous Center Is…

Q: In the figure shown, if wa=300rpm , solve for (a) the angular velocity of disk C (in rad/s) (b) the…

A: Given data ωA = 300 rpmrA = 2 inchrB1 = 4 inchrB2 = 2 inchrC = 6 inch

Q: 5.12 The circular cam is driven by link 2 at a constant angular velocity w2 = 15 rad/s ccw. Link 3…

Q: GENERAL RIGID BODY MOTION A disk is originally rotating at w = -8 rad/s. It is given a constant…

A: Given: initial angular velocity of rotor, ωo=8 rad/sconstant angular acceleration of rotor, α=1…

Q: The skateboard has a length of lAB = 1.30 m. Given the figure shown, determine (a) the velocity at…

Q: A wheel rotates for 5 seconds with a constant angular acceleration and describes during this time…

Q: In the following mechanism, se the vectorial upproach to determine conc and ve ur the arm AB has a…

A: Given ωAB=95.55 rpm=95.55 x 2π60rad/s=10 rad/secpointA and D are fixed so VA=VD=0Velocity…

Q: Determine the corresponding kinematic equations for the mechanism design shown, once determined to…

A: Given:-

Q: A wheel rotating with 20 rev/s is uniformly accelerated at 0.3 rad/s2 for 5 seconds. It then rotates…

A: Given data:- →For process 1-2:-Angular velocity at time t=0, ωt=0=20rev./sFor 1 revolution, angle…

Q: A circular body rotates according to the equation (S = 2 t4 – 4), Find the radius of the body to…

Q: Your design requires the piston P to move upward with a velocity of 300 in/sec at the instant shown.…

A: We have given that, Vp = 300 in/Sec IAB = 1.45 in. Angle A = 30o Lenght of crank connected to…

Q: 1. A bullet spins as the shot is fired from a gun. For this purpose, two helical slots as shown in…

Q: For the position shown where ? = 53°, point A on the sliding collar has a constant velocity of…

A: Given that , v= 1.25 m/s θ=53°

Q: The rod shown in the figure rotates with a counterclockwise angular velocity of 3 rad/s and a…

A: Consider the diagram as shown below for the accelerations of the point A.

Q: Find the velocity of the slider D and the angular velocity of link CD for the engine mechanism shown…

Q: For the instant shown in the figure, the angular velocity and the angular acceleration, of the bar…

A: As per honor code and answering guidelines I can answer 1st three subparts at a time.If you want…

Q: For the body shown. At the instant shown, point B moves in straight line in x positive direction…

A: Given data: The velocity of point B is vB=11i cm/s. The acceleration of point B is aB=6i cm/s2. The…

Q: What is the chain rule for angular velocity? If we know the angular velocity of the Orbital CCS…

Q: Determine the degree of freedom of the mechanism in the figure below. Then determine all the centers…

A: Please see the attached detailed solution:

Q: gular velocity of rod BC and the velocity of the slider block gular acceleration of rod BC and the…

Q: Problem 3 For the instant represented, link CB is rotating counterclockwise at a constant rate N=4…

Q: If rod CD is rotating with an angular velocity ocD. At the instant shown in the figure, which leter…

Q: 50 140 AT 30 60 150

Q: he angular velocity of rod BC and the velocity of the slider block he angular acceleration of rod BC…

Q: For the body shown. At the instant shown, point B moves in straight line in y positive directi with…

A: There are two types of accelerations that are acting on a circular surface. One type of acceleration…

Q: below has a crank that revolves clockwise at point O at a speed of 2000 rpm. Using vector diagrams,…

Q: A shaft rotating with a uniform velocity of 20 rev/s for 7 seconds. It is then uniformly accelerated…

A: Given data , iN=20rpst1=7siiα=0.6 rad/s2,t2=7siii t3=12s, stopped

Q: in the figure the wheel D rotates with an angular velocity ω1 of 2 rad/s counterclockwise. Find the…

Q: A wheel pinned at its center has a constant clockwise angular acceleration of a = 2" | at the…

Question

Read the question carefully and give me right solution according to the question. Remember use analytical and instantaneous center methods

The bar AB slides so that its bottom point A has a
velocity of 400 mm/s to the left along the horizontal
plane. What is the angular the angular velocity and
acceleration of the bar in the phase shown. Use two
methods: analytical and the instantaneous center
methods.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given Data

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

find an acceleration of the center of the beam (marked as a blue point) which is connecting both wheels , if it is known that linear velocity ot the wheels v=100km/h, r=0,8m and the distance drom the center of the wheel and the pont where the beam is connected (marked as red red distance)=0,4m, there is no slipping between wheels and the ground
The 250 g disk shown spins at the rate w1 = 750 rpm, while axle AB rotates as shown with an angular velocity ω2 of 6 rad/s. Find the Kinetic energy of the disk with this information.
A disk with mass m = 6.5 kg and radius R = 0.39 m hangs from a rope attached to the ceiling. The disk spins on its axis at a distance r = 1.32 m from the rope and at a frequency f = 18.9 rev/s (with a direction shown by the arrow). what is the torque due to gravity on the disk? what is the period of precession for this gyroscope? what is the direction of precession of the gyroscope?
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC,which in turn rotates about the terminal axis at O. At the instant shown, theangular velocity of the shaft OC is 10j rad/sec, and gear A is stationary. Deter-mine the angular velocity of gear B, and the velocity of a point D at the top ofgear B.
For the system given, the bar AB has an angular velocity of wAB=4 rad/s. By use of vector notation, determine the velocity of mass C, and the angular velocity of bar BC when ?=30°.
If we had the velocity and acceleration of the point A , find the Angular velocity and angular acceleration? where is The instantaneous center of the era?
For the system given, the bar AB has an angular velocity of wAB = 4 rad/s. By use of vector notation, determine the velocity of mass C, and the angular velocity of bar BC when theta = 30.
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC which in turn rotates about the terminal axis at O. determine the angular accelera tion of gear B when gear A is stationary and member OC has an angular velocity of 10j rad/sec and and angular acceleration of 25j rad/sec2 .
The following figure shows a top view of a spinning, cylindrical gyroscope wheel. The pivot is at O, and the mass of the axle is negligible. Use ?=2.9cm and ?=3cm. a. As seen from above, is the precession clockwise or counterclockwise? b. If the gyroscope precesses at 1.7 revolution per second, what is the angular speed of the wheel in revolution per minute? Insert your answer correct up to at least a third decimal place.
Find the magnitude and position of the balancing mass at a radius of 13cm by using the analytical method. Three masses m1, m2, m3, are attached to a shaft and revolve in the same plane. The masses are 12kg, 10kg, and 15kg respectively and their radii of rotations are 5cm, 6cm, 7cm respectively. The angular position of the masses m2, m3 are 45° and 145° from the mass m1.
A 3 in radius disk spins at the constant ω1 - 5 radian/s and a constant rate ω2= 4 radians/s. If the angle is 45 degrees, find the absolute acceleration at point P.
At the image below, what is the rotation of rod AB about point A if piston b moves to the right? Moreover, what is the magnitude of the acceleration of end a if velocity of end A is 7.5 m/s upward and is increasing at a constate rate of 18.75 m/s^2?