The bars ACE and BCD are supported by a pin and slot arrangement at C. ACE is supported by a pin at A, and bar BCD is fixed to the ground at B. а. Draw a FBD of the bar ACE. Determine all support reactions at A, and determine the slot reaction at C. b. Draw a FBD of bar BCD, and determine all the support reactions at B. l0lb ft M = ISo dbft = Soeb 3 ft ft 3 ft A 4 ft 4 ft ......Y...... C ---..Y......

The bars ACE and BCD are supported by a pin and slot arrangement at C. ACE is supported by a pin at A, and bar BCD is fixed to the ground at B. а. Draw a FBD of the bar ACE. Determine all support reactions at A, and determine the slot reaction at C. b. Draw a FBD of bar BCD, and determine all the support reactions at B. l0lb ft M = ISo dbft = Soeb 3 ft ft 3 ft A 4 ft 4 ft ......Y...... C ---..Y......

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.1P: Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached at...

See similar textbooks

Similar questions

The homogeneous 240-lb bar is supported by a rough horizontal surface at A, a smooth vertical surface at B, and the cable BC. Draw the FBD of the bar and count the unknowns.
Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached at A. Draw the FBD for the bar, recognizing that it is a two-force body. Determine the number of unknowns.
The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The uniform bar AB of weight W and length L is pinned to a sliding collar at A and to the sliding rod BD at B. The spring wound around rod BD has a stiffness k and is undeformed when rod AB is in the position =0. Determine the expression for the angle (other than =90 ) at equilibrium and investigate the stability of equilibrium for this position.
A slender homogeneous bar is bent into a right angle and placed on a cylindrical surface. Determine the range of b/R for which the equilibrium position shown is stable.
The jib crane is pin connected at A and supported by a pin connected collar on smooth rod at B. If x = 6.0 ft , determine the reactions on the jib crane at the pin A and smooth collar B. The load has a weight of 5500 lb Determine the reactions on the jib crane at the pin A Determine the reaction at B
The upper end of the bar of a problem is now leaned against a non vertical wall. Determine the minimum value of the angle θ for which equilibrium is possible for μs = 0.25 and for μs = 0.50
Don't copy from other websites solution. The wall crane supports a load of 660lb. The jib ABC has a weight of 152lb and member BD has a weight of 38lb. Each member is uniform and has a center of gtravity at its center. A)Determine the horizontal component of reaction at the pin A. B)Determine the vertical component of reaction at the pin A. C)Determine the horizontal component of reaction at the pin D. D)Determine the vertical component of reaction at the pin D. E)What is the force in the cable at the winch W?
The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 518 kN. Determine the magnitude of the pin reaction at A,B AND C in kN.
A35-kg disk rests on an inclined surface for which µs = 0.2. The disk is connected to a beamby pin connection at A and the link is supported by pin at B. The vertical load P is applied onthe link AB at a location as shown in Figure 3 (b) Determine the support reactions at pin A and B
determine the magnitude of the pin reaction at CD
The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 661 kN. a) Determine the magnitude of the pin reaction at A in kN. b) Determine the magnitude of the pin reaction at B in kN. c) Determine the magnitude of the pin reaction at C in kN. d) Determine the pressure in hydraulic cylinder BC in Pa if the cylinder has a diameter of 80 mm.