he blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB, which is controlled by the hydraulic cylinder BC. There is an identical linkage on the other side of the bulldozer. Applied loads shown are for both linkages and F = 518 kN. Determine the magnitude of the pin reaction at A,B AND C in kN

Q: Solve the question below on a sheet of paper and then upload a scanned copy of your work A plane…

A:

Q: 1000 mm -180 mm B 1280 kN F kN 500 mm 640 mm

A:

Q: 3. For the truss shown in figure below: > Determine the force in members BC, HC, and HG. After the…

A: Given,            tanθ=35tan ϕ=25

Q: The frame shown below supports 100lb weight. The cable is attached at A and passes over a smooth peg…

A: Given data as per question Supporting weight =100 lb considering the FBD of  BD

Q: For the bracket and loading of Prob. 4.7, determine the smallest distance a if the bracket is not to…

A: When bracket is not to move, the reaction force at A will be zero i.e. the bracket will be in…

Q: #4 A small winch is used to raise a 120 Ib load. Determine the reaction forces at points A and B. -…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: For the frame shown in Figure, determine the reaction at A, B, and D. 80 kN/m 20 kN/m B 4 m 6 m

A:

Q: Determine the magnitude of each of the reactions at the supports; roller at A and pin at B. 0 = 30…

A:

Q: Problem Set: 9. Determine the reaction at the roller F for the frame loaded as shown in the figure.…

A: solution :

Q: For the frame shown below, Is supported by pins at C and D. Determine the magnitude of reaction at C…

A: Consider the free body diagram of the member CBA as shown below.

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 660 N, a =…

A: GivenF=660Na=675mmb=290mmθ=25oϕ=64o

Q: Calculate the horizontal reaction at the hinge support A of the equilibrium rigid body shown in the…

A: The free body diagram of the beam is a follows:

Q: The plate supported by a roller at A and pin-joint at B is subjected to three external forces as…

A:

Q: Problem 2: For the frame shown, find the horizontal and vertical components of the reactions at A…

A:

Q: he given truss below is loaded vertically downward with 4KN and 8KN at points C and D, respectively,…

A: Find the internal force in members and percentage error.

Q: (iv) Two identical rods MP and MN each of mass m are hinged together (Figure 4) at M and supported…

A: Drawing the Free Body Diagram of the bar as shown below, Consider the…

Q: PROBLEM 2 The elements of a floor jack are shown in the figure. If the hydraulic cylinder AB is…

A: According to the question: ∑Md=0 1.25EFcosα + 1.25EFsinα = 0  EF=0 BY equating the sum of forces in…

Q: Determine the pin reactions at A, B and C of the frame shown below.

A: 41-400 Drawing the free body diagram of the frame as shown below, Calculate reaction at A and C,…

Q: The frame AB is supported by a pin at A and a pin at B. It is subjected to a concentrated force of…

A: Draw the free body diagram of the frame AB.

Q: 7 kip 10 kip 2 kip 5kip -8 ft -6ft- -6 ft- A 0.5 kip 6 ft B

A:

Q: The elements of a wheel-height adjuster for a lawn mower are shown. The wheel (partial outline shown…

A: Data given -  Wheel height adjustor for a lawn moved

Q: Problem #2 Given: Two roughnecks apply forces of equal magnitude 500 N to the torque device shown…

A: To Draw:  The F.B.D of member ACB. Free body diagram  The F.B.D of ACB is,

Q: Compute the reactions at the pins B and C if the load supported by the lever weighs 3000 N

A:

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 750 N, a =…

A: Given:F=750 Na=775 mmb=340 mmθ=30

Q: Using the method of members (analysis of frames), calculate the resultant pin reactions at A, B and…

A:

Q: The truss carries the loads as shown in Figure 2. The truss is supported by pin at A and smooth…

A: The free-body diagram of the truss is given by,

Q: The blade of the bulldozer shown below is rigidly attached to a linkage consisting of the arm AB,…

A: A pin support will exert both horizontal and vertical components of reaction as the reaction forces.…

Q: The given truss below is loaded vertically downward with 4KN and 8KN at points C and D,…

A:

Q: Determine the total support reactions at A and B for the truss loaded below. -5 at 3 m = 15 m- 12 kN…

A: For Calculating the support reaction for  a given truss we need to apply equilibrium equations.…

Q: 3. A table 600 mm by 600 mm is mounted on three legs. Four loads are applied as shown. Determine the…

A: Given Plane load To find Reactions

Q: Determine the magnitude of the pin reaction at A in kN. b) Determine the magnitude of the pin…

A: Given: To determine: The pin reaction at A  The pin reaction at B  The pin reaction at C

Q: A T-shaped bracket supports the four loads shown. Determine the reactions at A and B if a = 12cm.…

A:

Q: In the figure shown, the frame is supported using a hinge in point A and a roller in point B. The…

A:

Q: Determine the magnitudes of all pin reactions for the frame loaded as shown. Assume F = 660 N, a =…

A: Consider the free body diagram for the member ABC.

Q: Bar ABC rests against a smooth surface at end C and is supported at end A with a ball-and-socket…

A:

Q: a). A fixed crane has a mass of 1000 kg and is used to lift a 2400 kg crate. It is 5. held in place…

A: Given:-  Mass of crane (m) = 1000 kg Mass of crate (M) = 2400 kg To Find:-  Draw free body diagram…

Q: Determine the values of the reactions in the figure shown which contains 3 segments AB, BC, and CD…

A:

Q: is supported at the left end 6-86 Beam CD of Fig. C by a smooth pin and bracket and at the right end…

A: Given Applied load = 5 kN To find Reaction at C Force in cable when load is applied

Q: (a) Determine the magnitude of the pin reaction at A in kN. (b) Determine the magnitude of the pin…

A: Given: TO determine: Pin reaction at A, B,C

Q: Determine the reactions at the roller E and pin F if force 130 lb is located at point A as shown in…

A:

Q: 5 m B 3 m 3m 80 kN 5 m

A: Draw the free body diagram of the system. Calculate the angle θ.

Q: 75 mm 30° В P 200 mm D 100 N E 50 N

A: given;

Q: 3. Find the horizontal and vertical components of the forces at all joints. The reaction at point B…

A:

Q: 2 ft -2 ft 90. 65 200 lb 100 lb 2. A beam AB is loaded as shown. The beam is pin-connected to the…

A: According to the given details in the question.  We need to find reaction at A and tension in the…

Q: In the figure shown, the frame is supported using a hinge in point A and a røler in point B. The…

A:

Q: The truss above has concentrated loads as shown. The wind loads of 50 KN are perpendicular to the…

A:

Q: Determine the force in member BD and the components of the reaction at C.

A:

Q: In the structure shown, force F is applied at point A at an angle of 6 in the direction shown. Pins…

A:

Q: C В P P B D F E A D E (c) (d) Figure P4.141

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.