The beam AB is a composite section and is formed by welding a PFC Channel1 and a universal beam (UB) Section 3 (See Table 1) together as shown in Figure 2(b). The individual sectional properties are given in Figure 2(c) and (d) where x, and y, indicate centroidal axes.

The beam AB is a composite section and is formed by welding a PFC Channel1 and a universal beam (UB) Section 3 (See Table 1) together as shown in Figure 2(b). The individual sectional properties are given in Figure 2(c) and (d) where x, and y, indicate centroidal axes.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A composite bar is rigidly attached to the wall at A as shown in the figure. Axial loads are applied at the positions indicated. 3 m 2.5 m C 1200 kN 900 kN 80mmØ 100mmØ E = 83 GPa Bronze E = 200 GPa Steel Which of the following most nearly gives the deformation of C? a. -0.7855 mm О Ъ. +0.8575 mm c. +0.7855 mm o d. - о.8575 mm
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 60 GPa] with a cross-sectional area of A1 = 870 mm?. Bar (2) is a bronze alloy [E = 92 GPa] with a cross-sectional area of Ay = 520 mm?. Assume L$=2.6 m, La=2.9 m, a=0.7 m, b= 1.3 m, and c= 1.1 m. All bars are unstressed before the load P is applied; however, there is a 3.9-mm clearance in the pin connection at A. If a load of P= 58 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains € , E2, in bars (1) and (2). (c) determine the downward deflection vA of point A on the rigid bar.
Two T-shape sections are welded together to create a composite l-beam section as shown below. Determine the safely uniform load w (kN/m) that the beam can carry throughout its entire span. 270mm 30mm 20mm 160mm Welded Joint 130mm 30mm 135mm Beam Length = 4 m Consider the following stresses: fb(T) 3 125 МPа fb(C) = 130 MPa x at the welded joint = 20 MPa Find: 1. The Neutral Axis from the base 2. moment of inertia with respect to the horizontal centroidal axis 3. Q at the welded joint 4. Considering the maximum flexural stress in tension, WNAX is equal to KN/m. 5. Considering the maximum flexural stress in compression, WMAX, is equal to 6. Considering the stress at the welded joint, wMex is equal to kN/m.
Problem 2: A composite shaft is composed of a solid section AB and a tubular section BC, both of which have circular cross sections. Section AB is made of steel and has a radius of 1 in. Section BC consists of a brass core, with a radius of 0.5 in, surrounded by a steel tube, with an inner radius of 0.5 in and an outer radius of 1 in. Use Gs = 11,500 ksi for steel and Gb = 5600 ksi for brass. The shaft is attached to a fixed support at A, and a torque of T = 50 ft-lb is applied at the free end C. 0.5 in 1 in 2 ft B T = 50 ft-lb 3 ft (a) Calculate the total angle of twist (magnitude only) between and C. (b) Calculate the maximum shear stress in the brass. (c) Calculate the maximum shear stress in the steel.
The composite bar shown is firmly attached to unyielding supports. An axial load P= 200 kN is applied at 20°C. Assume a = 11.7 um/(m °C) for steel and 23.0 um'(m °C) for aluminum. Find the reaction at the left support. a. find the reaction at the left supportb.find the stress at the steelc. find the stress at the aluminum
A composite bar BCD has a uniform external radius R. = 10 cm. Segment BC is solid steel, while segment CD is composed of a copper core of radius R:= 1cm bonded inside a steel sleeve. The lengths of the two segments are Lec= 2 m and Lco= 1 m. The material moduli are Esteel = 200 GPa and Ecopper= 100 GPa. The bar is fixed at B and tensile loads are applied at section D (Fo= 1000 kN) and at section C (Fc= 400 kN). Compute the following: Determine Axial stress of steel in segment BC in MPa. 2m 1m 400 KN 1000 KN
Two solid cylindrical rods are joined at B and loaded as shown. Rod AB is made of steel E 200GPa and rod BC of brass E 105GPa. Determine (a) the total deformation of the composite rod ABC, (b) the deflection of point B. 250 mm 300 mm 30 kN -30 mm 40 kN -50 mm
A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. p-211. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m Figure P-211 Aluminum A = 320 mm² 1.5 m 2P
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
This is Structural theory. Formula: For #1 : r-3-c #2: r+m-2j #3: r+m-2j
The static indeterminacy of the structure shown below is Hinge - K I J H F E G A B D
a composite shaft AC is made by shrink-fitting a titanium-alloy sleeve of length L3 = 4 ft over segment BC of a 6-ft-long aluminum-alloy rod. This makes a three-component shaft, which is fixed against rotation at ends A and C. The shear moduli are G1 = G2 = 6 X 103 ksi and G3 = 4 X 103 ksi, respectively, and the diameters and d1 = d2 = (di)3 = 2 in., and (do)3 = 2.5 in. (a) Using the Displacement Method, determine the angle of ro- tation at B, og. produced by an applied torque Tg = 50 kip . in. (b) Determine the maximum shear stress (Tmax)1 in the alu- minum segment AB, (Tma)2 in the aluminum core segment BC, and (Tmax), in the titanium sleeve BC.