What will be the pressure head of a point in mm of Hg if pressure hcad of that point is equal to 63 cm of water? Assume specific gravity of Hg is equal to 136 nd specifle weightof water is 9800 N/m. .

Answered: Image /qna-images/answer/1ab75516-de19-4841-bf1d-2b2edc63a345.jpg

What will be the pressure head of a point in mm of Hg if pressure hecad of that point is equal to 63 cm of water? Aasume specific gravity of Hg is equal to 136 nd specifle weight of water is 9800 N/m.

What will be the pressure head of a point in mm of Hg if pressure hecad of that point is equal to 63 cm of water? Aasume specific gravity of Hg is equal to 136 nd specifle weight of water is 9800 N/m.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.9P

See similar textbooks

Related questions

Q: Q5 Determine the reaction forces at B and C of the continuous beam below. It is calculated that the…

Q: Using SDM and MDM, determine the reactions on the beams below: 10 kN 5 kN/m Beam 2: A В C 77777 30…

Q: Use the moment distribution method to analyze the frame, and draw the shear and moment diagrams.

A: Moment distribution method The moment distribution approach was developed by Hardy Cross for…

Q: A diagram shows how the neutral surface of the structure changes shape under a given loading…

Q: A square slab is simply supported on three sides and is free on the fourth side. If the moment…

Q: Draw isometric view

A: Isometric view is the representation of 3d object in 2d plane. In isometric view generally the angle…

Q: For the given data of a close traverse, determine the missing bearings of course CD and DE solve the…

A: To Determine The missing bearings of course CD and DE solve the AREA using DPD. Sketch the traverse.

Q: What minimum theoretical depth is needed for the 500mm wide beam shown if no torsional reinforcing…

A: Given -

Q: Determine the joint moments E=200,000 MPa, I=104 x106 mm4 (Hint: Consider 8 cycles of C.O.-Bal)…

Q: If a force of 6O Ib stretches a 10-in spring to 14 inches, find the work done in stretching the…

A: Given Force of 60 Lb is used to strech a 10 in spring to 14 in .

Q: From the figure below, assume 8 K1 = K2 = 4 K3 = 2 K4 and that layer 2 and 3 are of equal heights.…

A: k1 = 4.6 x 10-2 cm/s

Q: Determine the y-coordinate of the centroid of the shaded

Q: Component Pump 60 m Water 2)

Q: Design a two tier grillage foundation to carry an axial load of 1000 KN. A base plate 700 x 700 mm…

Q: In the figure, a 2" pipe leads downhill from a reservoir and discharges into air. If the loss of…

Q: Difference between swamps and marshes in terms of plant existing in the area and the water level?

A: in this question Difference between swamps and marshes in terms of plant existing in the area and…

Q: 6 KN Fo the beam shown, draw SFDand BMD. Ans. Rg -19.5KN, RC= 10.5 KN. 15 KN.m 17KN, m SKNIM 2m 2m 2…

A: The loads acting on the beam are given .

Q: Q 1/ The University of Anbar purchased equipment for the purposes of the reconstruction campaign at…

Q: Refer to the figure shown a = 11.7 x 10/°c E = 200 GPa A = 1,200 mm2 a = 23 x 10/°C E = 70 GPa A =…

Q: Consider the beam undergoing two distributed loads and a point force below. (a) redraw and the…

Q: The number of flow channels and head drops is 4 and 12 respectively. If the difference in the…

Q: Problem 3 For the given data of a close traverse, determine the missing bearing of courses CD and…

A: Given data:

Q: 20 kN.m 2 kN/m A- 个个个 2m 4m 2m

Q: A constant head orifice from a tank feeds water into a flume (open channel) 5m in length and 500 mm…

Q: 10 20 40 60

A: Particle size distribution D10 = percentage of finer than 10 D60 = percentage of finer than 60 D30…

Q: The cantilever beam consists of a W530 × 74 structural steel wide-flange shape [E = 200 GPa; I = 410…

A: Given Data: LAB = 2.6 m, LBC = 2 m, P = 39 kN, w = 35 kN/m.

Q: Problem 3 Given in the tabulation below are the observed forward and backward bearings of an open…

A: 1) convert all the quadrantal bearings into whole circle bearing and plot the traverse then proceed…

Q: sornm diam. Lorfice Cy=0,92) O.5m

Q: Determine the axial load at point B for the beam below. 12k 60° B 8 k -5 ft 5n Sn- -5 ft- -5 ft…

A: Determine the axial load at point B for the beam below.

Q: 2. Determine the shear force at point A for the beam shown below. 80 kN m 90 kN 100 kN- m 75 kN -4…

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

Q: Date Due Sunday, S/8/2022 Assignment Solve the problems below and insert your answers into the…

Q: Water is dripping into a hemispherical bowl with a radius of 8 cm at a rate of 1 cubic cm per…

Q: 1900 lb 400 lb 60 lb/ft A D |B C 8 ft - te 6 ft - 4 ft

Q: Q4-In the traverse below if the Azimuth of AB = 30° 30' 30" find the coordinates of point B and C В…

Q: -esign a two tier grillage foundation to carry an axial load of 1000 kN. A base- plate 700 x 700 mm…

Q: The first step in drawing a shear diagram is Select the correct response: drawing a free body…

A: Correct answer- calculating support reaction Explantion:- -The first step of shear diagram is to…

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

A: Find the twist development in steel from help B.

Q: An aluminum tube of outer diameter R2 = 50 mm is heated such that it is mounted over a steel shaft…

A: We will find torque in 1 and 2.

Q: What will be the pressure head of a point in mm of Hg if pressure head of that point is equal to 53…

Q: Determine the bending moment (M) in kNm at point A for the beam as loaded in Figure 3.2b8. Given a -…

Q: Determine the volume V and total surface area A of the solid generated by revolving the area shown…

Q: The number of flow channels and head drops is 4 and 12 respectively. If the difference in the…

Q: Using the method of composite determine the location of the centroid of the 100 mm areas, shaded…

A: To Determine the location of the centroid of the shaded area

Q: A composite bar is rigidly attached to the wall at A as shown. Axial loads are applied at the…

Q: Problem 5) Find the equivalent resultant force created by the distribution of sand as well as its…

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 504 mm and a wall…

A: Given data:- Internal Pressure P = 2.4 MPa Internal diameter D = 504 mm Wall thickness t = 10 mm…

Q: The shear diagram for a beam is given below. 30 kN 25 kN -10 kN -20 kN 25 m+is m-t--2 m m -2.5 m…

Q: 3. In the Figure 1-61, the incline force P is applied at the center which is necessary to start the…

Q: A cantilevered structural member is fabricated with the cross section shown below and is…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

What will be the pressure head of a point in mm of Hg if pressure hcad of that point is equal to 63 cm of water? Assume specific gravity of Hg is equal to 136 nd specifle weight
of water is 9800 N/m. .

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2) Calculate the value of pressure ∆p onside the rain water droplet , if we knowthe radius R=0.2mm and the surface tensionδ = 0.074 N/M
What height of a column of a special gage liquid (sp. gr. = 2.95) exert the same pressure as a column of oil 4.5 meters high (sp.gr. = 1.19)? a. 1.58 m b. 1.28 m c. 1.85 m d. 1.82 m
Compute the pressure drop in kPa per km of a horizontal 600 mm diam. steel pipe carrying 450 liters/sec of a heavy fuel oil having a sp.gr. of 0.80. Friction factor f = 0.018.
A cylindrical tank contains a certain liquid (SG = 2.75) to a depth of 0.4 m. A pressure of 78 kPa is acting at the surface of the liquid. If it is accelerated upwards at 3.43 m/s2, what is the resulting pressure (kPa) at the bottom of the tank?
I'm looking for a conclusion based on this given result from the hydrostatic pressure on plane surface 1. PARTIAL IMMERSION Trials 1 2 3 Total weight on arm M (grams) 50 g 100 g 150 g Depth of Water y (mm) 49 mm 65 mm 80 mm Force on End Surface (experimental) (N) 734.41 N 1512.76 N 2334.59 N Force on End Surface (theoretical) (N) 883,267,875 N 1,554,271,875 N 2,354,400,000 N Depth of Center of Pressure (mm) 16.33 mm 12.67 mm 26.67 mm 2. COMPLETE IMMERSION Trials 1 2 3 Total weight on arm M (grams) 250 g 300 g 450 g Depth of Water y (mm) 109 mm 122 mm 160 mm Force on End Surface (experimental) (N) 4109.31 N 5009.00 N 7704.15 N Force on End Surface (theoretical) (N) 4,340,925,000 N 5,297,400,000 N 8,093,250,000 N Depth of Center of Pressure (mm) 73.12 mm 83.57 mm 117.58 mm
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized aire in the tank. a.) Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. b.) What gage pressure in p1 in kPa, is needed to provide the given flow rate?
The system in Fig. P2.48 is open to 1 atm on the right side. (a) If L = 120 cm, what is the air pressure in con tainer A? (b) Conversely, if Pa = 135 kPa, what is the length L?
A sluice gate flows into a horizontal channel as shown in the figure. Determine the flow through the gate per meter width when y=1.0m and d1=6m. Assume that the pressure distributions at section 1 and 2 to be atmospheric and neglect losses in the channel. Use coefficient of contraction Cc= .85 and coefficient of velocity is Cv=.95.
Show the necessary figures (if applicable) 2.3) Points A and B are separated by 915 m of new 152.4 mm diameter cast iron pipe. 50 lps of water flow from point A to point B. Point B is 18.5 m above point A. What must be the pressure at point A if the pressure at point B is 345 kPag and the head loss between A and B is 54 m? 2.4) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Two Water flows from reservoir A to reservoir B through two pipes as shown below. Determine 1) thedischarge in the pipe, 2) the pressure at point P. Assume α = 1.0 at all locations and neglect any minor headloss
If a triangle of height d and base b is vertical and submerged in liquid with its vertex at the liquid surface (see Fig. 2), derive an expression for the depth of its center of pressure. a) ?/2 b) 4?/3 c) ?/4 d) 3?/4 e) ?/3
Show complete solution(need ASAP): A flow net has been drawn as shown in the figure. Points A and C are at elevation ℎ1 and ℎ2 respectively above the datum. ? = 4 m ℎ1 = 4.7 m ℎ2 = 1.4 m Determine : a. Compute the piezometric pressure at point A in kPa. b. Compute the piezometric pressure at point C in kPa. c. Compute the piezometric head at point B in meters.