The beam in (Figure 1) is made from three boards nailed together as shown. Part A If the moment acting on the cross section is M = 560 N- m. determine the maximum bending stress in the beam. Express your answer to three significant figures and include appropriate units. HÁ Omax = Value Units igure 1 of 1> Submit Request Answer 25 mm Provide Feedback 150 mm 20 mm 200 mm M 20 mm

The beam in (Figure 1) is made from three boards nailed together as shown. Part A If the moment acting on the cross section is M = 560 N- m. determine the maximum bending stress in the beam. Express your answer to three significant figures and include appropriate units. HÁ Omax = Value Units igure 1 of 1> Submit Request Answer 25 mm Provide Feedback 150 mm 20 mm 200 mm M 20 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 14 ft, W10x54 column is pinned at one end and fixed at the other. What is the buckling stress of the column in ksi? Use E = 29,000 ksi and report your answer to two decimal places the answer is 135.63 please show steps!
The two vertical rods attached to the light rigid bar in the figure are identical except for length. Before the load W was attached, the bar was horizontal and the rods were stress-free. Determine the load in each rod if W = 6600 lb. (Determine load for rod A & B in lbs)
REFER TOTHE GIVEN VALUES IN THE FIGURE BELOW. THANK YOU. Use VIRTUAL WORK METHOD and determine the following unknowns on the truss system shown below. Use A = 500 mm2 and E = 200 GPa. Show complete and organized solution. Round-off your answers to two decimal places. - Horizontal displacement of joint G due to the applied loads in mm - Horizontal displacement of joint C considering that the top chord members experience 60 °C increase in temperature in mm. Use α = 10-6/°C
33333. From the given beam loaded as shown, Let P = 3 kN, L = 7 m, a = 3 m. E = 200GPa, I = 2000 x 10^6mm^4
N.6.1. Find principle stress if the values are as given: Upper side stress:300lb/9pulg2 Tangential in right direction: 120 lb/pulg2
The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an axial load of 50 kNkN. Est=198 GPa�st=198 GPa, νst=0.32�st=0.32.
The end chord of a timber truss is framed into the bottom chord as shown in the figure. Neglecting friction, compute dimension b (in mm) if the allowable shearing stress is 880,000 Pa. (round-up your answer to a nearest whole number that is divisible by 5, no need for unit)
A = 3 B = 4 C = 1 D = 0 kindly answer the magnitude and if possible the forces
Q.3 A uniform steel plate 360 mm square with a mass of 25 kg is suspended in the horizontal plane by the three vertical wires as shown. Calculate the tension in wire C. (round answer to one decimal places)
A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter is reduced to 12.99265 mm. Determine: a. The modulus of elasticity. Answer: 200 GPa. b. Poisson's ratio. Answer: ν = 0.30 c. Shear modulus. Answer: G = 76.92 GPa. d. The deformation of the rod. Answer: δx = 0.09415 mm. Recommendation: Obtain the modulus of elasticity using the slope of the straight line.
Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given: A1 = 0.94 in2, A2 = 0.38 in2, P1 = 81 kips, P2 = 49 kips, P3 = 31 kips and E = 29x106 psi Your final answer should have three decimal places
Two forces FA =168 lb and FB =265 lb are acting on the bracket shown with axes x,y,v and w indicated. If the angle measurements on the figure are c=20o , d=9o , f=15o and g=7o, determine the x-component of FA (lb).