Answered: The beam is loaded as shown. which of…

The beam is loaded as shown. which of the following nearly gives the centroidal moment of inertia in mm4? 240 mm W = 12 KN/m 60 mm 200 mm 4m 4 m 4 m 60 mm O 195438181.8 O 145938181.8

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A post having a hollow, circular cross section supports a P = 3.5 kN load acting at the end of an…

Q: Q4. Write short notes on meandering

A: step 1-

Q: 13. Which one is not a key aspect of IRS? Everyone must have a sincere wish to prevent accidents and…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Solve for the reactions, draw the shear and moment diagram, indicate the degree of the curve and box…

Q: A beam is subjected to equal bending moments of Mz = 3400 N-m. The cross-sectional dimensions are b…

Q: Solve and show complete solution. From the technical description below, what is the coordinates of…

Q: Problem: A gravity dam in the figure carries water that is 12 m deep on its upstream side. The…

Q: A horizontal water jet with a velocity of 10 m/s and cross-sectional area of 10 mm2 strikes a flat…

A: given-velocity v=10m/sarea A=10mm2density ρ=1000 kg/m3

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

Q: -12"- h = 9" #9 @ 5" o.c. clear - 12" Typical Section 19

A: Given data for slab breadth = 12 in = 12 in12 in= 1 ft height = 9 in = 9 in12 in = 0.75 ft dia of…

Q: Determine the best hydraulic section for the following geometric

A: ###Determination of best hydraulic section for part i and ii

Q: A flitch beam is composed of two 50x300mm planks reinforced with a 12.5mm steel plate as shown.…

A: We will solve this question in step no. 2

Q: 0.5 cm 5cm water Linseed oil (SG=0.92) 10cm T//////

Q: A grab driver is traveling at 15 m/s when the traffic light 787 ft ahead suddenly turns red. The…

Q: 2. Assume the separation for A, B, and C. With the instrument midway between A and B the readings…

Q: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the…

Q: A beam is subjected to equal bending moments of M, = 3000 N-m. The cross-sectional dimensions are b…

A: Given : Applied bending moment, Mz = 3000 N-mCross-sectional dimensions are : b = 190 mm, c = 30 mm,…

Q: 1. Solve for the reactions, draw the shear and moment diagram, indicate the degree of the curve and…

Q: Quiz No. 1 (Truss) Given the Truss as shown below with load P1 = X N and P2 = 3X N. Using Method of…

Q: A sand layer found at sea floor under 20 m water déptri is characterized with relative density =…

Q: A side hammer is collected with both shaft and journal sliding support, as illustrated in below…

Q: •Given the following information for wastewater plant, the plant is an activated sludge system with…

A: Answer Flow rate Q = 60000 m3/d Volume of Aeration tank = 7500 m3 Efficiency of aeration tank = 85%…

Q: square section tank of 10FT side and 7FT length as shown has the top of one side wall in the shape…

Q: 3. In the figure below, a vertical angle of -14°30' is read to a target 1.75 m above point M. The…

Q: Oil (s=0.80) and viscosity (u = 0.098 Pa - sec) flow from a reservoir of surface elevation 100…

Q: 4. A laboratory analysis of the settlement of flocculated water gave the following results for a…

Q: d lventia 4 the Compulu for the moments Conmposilu figm with Kepet to to fo loving a) X 6) yn )…

Q: PROBLEM O3: Given the figure below, (a) determine the flow rate in the siphon shown. Diameter of the…

Q: PROBLEM 01: Given the figure below, (a) determine the value of h in the siphon shown if velocity at…

A: step 1-

Q: 120 kN/m 35 12 kNm 24 kNm 6 kNm 6 m 2 m 1 m RA Rg EMA = 0 = ??? Rg =353 kN %3D Unit of M = kNm RB =…

Q: Using Simpson's 1/3 Rule

A: Given: F(x)=sin(x) n=10 To find: ∫02sin(x) dx using Simpsons 1/3rd rule

Q: Problem: A gravity dam in the figure carries water that is 12 m deep on its upstream side. The…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: 1.1 how to use a level 1.[Calculation] To calculate the elevation of some points, a leveling route…

A: surveying : The technique, profession, art, and science of identifying the two-dimensional or…

Q: P16.8 Shearing force for sections 1-1, 2-2, and 3-3. 24 ft

Q: What is the ratio of the strain energy in bar X to that in bar Y when the material of the two bars…

Q: Why is it important to calculate stress in beams?

A: The stresses are produced in beams when they are subjected to loadings. The stresses that are…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

Q: What is the ratio of the strain energy in bar X to that in bar Y when the material of the two bars…

Q: 2. The bending moment acting on the triangular cross section of a beam is M = 3.6 kN m. Determine…

Q: Find: Using the Principle of Virtual Wo Point Cof the beam. Use BMDS and the

Q: 2-19. Determine the reactions on the beam. 45 kN/m 30 kN/m 30 kN/m 60 810 kN- m 3.6 m 3.6m Pros,…

A: A loaded beam is given and it has been asked to determine support reactions. Please refer step 2 for…

Q: Q4. Write short notes on meandering

Q: EXERCISES 2-18. Determine the reactions on the beam. The support at B can be assumed to be a roller.…

A: Draw free body diagram Hinged have two restrained Roller have one restrained Equilibrium…

Q: 3. For a water supply with a river source and a water treatment plant, describe what happens to the…

A: River water quantity and quality strongly depends on its runoff system, the seasonal changes and the…

Q: Q1 A soil meant for road construction is said to have a CBR of 5% explaining the meaning behind this…

A: Three questions has been asked, as per guidelines the first question is answered here. CBR means…

Q: 1.In item No. I what is the length of m or AP? a) 4,226.67m b) 4,567.34 c)…

A: To find length of BP and AP

Q: A non-homogenous soil deposit consists of a silt layer sandwiched between the fine-sand layer at top…

Q: 3. Explain why use chemicals is required in water treatment 4. Give the reasons why settlement in a…

A: To find:- We have to draw reference of use of chemicals in water treatment. We also have to draw…

Q: 2-26. Determine the reactions at the truss supperts A and B. The distributed loading is caused by…

A: A loaded truss is given and it has been asked to determine support reactions. Please refer step 2…

Q: Q3. (a) Explain four characteristics of a plastic hinge. (b) Find the collapse load for the…

A: The given question is based on Plastic Analysis which comes under Steel Structure.

Question

The beam is loaded as shown. which of the
following nearly gives the centroidal
moment of inertia in mm4?
240 mm
W 12 KN/m
60 mm
200 mm
4m
4 m
60 mm
195438181.8
145938181.8
none among the choices
154938181.8

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

20 -In the cantilever beam in the figure, bar clearance L= 225 cm and single load acting on the free end of the bar P = 12 kN. The cross-sectional effects at point B will be calculated. Accordingly, the Moon on the fixed support at point A=? A) None.B) 27000C) 12000D) 0E) 9000
I cannot understand these For point of contraflexural, 40090300=200×x90300 x=2 m θA=0 (fixed support) θDA=θD-θA=θD=Area of MEI Dia between A and D = 19030012×600×3+600×4+12×300×3-12×200×2 =355090300 θD=0.03931 radianθD= 2.252° Deflection at point D ∆D=31-CosθD ∆D=2.3176×10-3 mm Deflection at point D is 2.3176×10-3 mm
Compute the total net deflection of the simply-supported beam with the following properties listed below. (Include the sign if it is negative) Properties:Length = 11.46 mWidth = 302 mmDepth = 435 mmeccentricity = 96 mmEc = 14,368.22 MPaPrestressing Force = 461 kNUnit weight of concrete = 23.16 kN/m3
DET. THE VALUE OF P THAT WILL CAUSE DEFLECTION OF THE 150X220 mm BEAM EQUAL TO 32mm (AT POINT C) WITH THIS VAIUE OF P , WHAT IS THE DEFLECTION AT POINT B USE E=65 GPa
DET. THE VALUE OF P THAT WILL CAUSE DEFLECTION OF THE 150X220 mm BEAM EQUAL TO 32mm (AT POINT C) WITH THIS VAIUE OF P , WHAT IS THE DEFLECTION AT POINT B USE E=656Pa
The shorter legs of two 6”x 4” x 1⁄2” angles arewelded to a 12”-20.7-lb channel. Determine themoments of inertia of the combined sectionwith respect to centroidal axes respectivelyparallel and perpendicular to the web of thechannel. For the 12”-20.7-lb channel, its area is 6.03 sq. in.; x̄=0.70; ȳ=0; web thickness t = 0.280"
Determine the deflection at midspan of the structure Group of answer choices (-5wL^4)/384EI (5wL^4)/384EI (wL^3)/24EI (-wL^3)/24EI
For the built-up shape shown in the figure, determine: a. The location of the plastic neutral axis from the top edge of the flange in mm (ANS 11). b. The plastic section modulus of about the horizontal axis in x106mm3 (ANS 0.214) c. The plastic moment with bending about the vertical axis if Fy = 345 Mpa kN-m. round of to the nearesrt whole number (ANS 43).
A 450-N is in contact with a level plane of fk = 0.10. The block is acted upon by a horizontal force of 75N. The block reaches a velocity of 15m/s, starting from rest. If the 75-N force is then removed, how much longer will the block continue to move?
The tensions of the ropes used in pulling a boat along a river by 2 carabaowhich are on opposite side and walking parallel to the river bank are 400Nand 360N. The angle between the ropes is 600. Find the resultant of thepulling force on the boat. Also, determine the angle that separates eachof the rope from the boat.
The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.
Replace the loading system by an equivalent resultant force and couple moment acting at point ?. Length AB = 1m Length BC = 2m F1 = 80 N F2 = 60 N F3 = 120 N Angle with respect to x-axis = 32 degrees Moment couple = 195 Nm