The beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm2 and 8 mm2 respectively. Determine the position d of the 6 kN load so that the average normal stress in each rod is the same. В 6 kN d A 3 m

The beam is supported by two rods AB and CD that have cross-sectional areas of 12 mm2 and 8 mm2 respectively. Determine the position d of the 6 kN load so that the average normal stress in each rod is the same. В 6 kN d A 3 m

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter6: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 6.4P: Refer to Figure P6.4. A strip load of q = 900 lb/ft2 is applied over a width B = 36 ft. Determine...

See similar textbooks

Related questions

Q: A group of 9 friction piles, 10 m long is used as a foundation for a bridge pier. The piles used are...

Q: Which of the following best give the value of the lateral torsional modification factor, Cb, of the ...

Q: Find the velocity of the block when v. -4 [m/s]. %3D Va BLOCK

A: When C point moves x distance upward then Block will move 2x upward because there will be displaceme...

Q: The tank shown has one curved surface restraining a body of static fluid, with the following dimensi...

A: To determine the magnitude of the resultant force on the curved surface. Given, Width of tank (w) ...

Q: A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of rei...

A: width of beam = 450mm depth of beam = 600mm

Q: What will be the efficiency of a joint for which design strength of joint in double shear is 619.89 ...

Q: Solve the following problems. Provide complete solutions and summary of answers. The dry density of ...

Q: (a)Determine the Young's modulus for this particular concrete under

A: Givendata: Maximum compressive stress σE = 20x107 Pa. Maximum compressive strain e = 8x10-3.

Q: From the Figure, Determine the following: 80 kN/m 10 kN 20 kN/m 3 m- 4 m- 1 m a. Reactions at the Su...

Q: 2.5m 3.2m A Cable 1 Cable 2 B 4.0m 2.3m MN kN

Q: Question 18 A rigid pavement has a wheel load capacity of 53.96 kN. The allowable tensile stress of ...

Q: Determine

Q: A 100 mm x 200 mm beam 6 m long is supported by a roller at its ends and at midspan. It carries a un...

A: Given data: Cross-sectional area=100×200 mm

Q: Question 8 Find the moment of inertia of the area bounded by the parabola y2 = 4x, x-axis, and the l...

Q: The copper pipe (G - 45GPA) has an outer diameter of 50mm and an inner diameter of 30mm, It is fxed ...

A: We have to determine the value of rotation of the free end with respect to the fixed end of the give...

Q: A dam with vertical upstream tace is 6.5 m high. 32 m wide of the bottom and 0.5 m at the top. Consi...

Q: Problem E A 4-meter-thick sand overlies a thick layer of clay. The water table is 1.80 meters below ...

Q: -10. TRANSIT RULE. Given in the accompanying tabulations are observed and calculated data for two di...

A: ∑L=∑NL+∑SL=+423.70-422.23=+0.47∑D=∑ED+∑WD=+431.43-422.34=-0.91 ∑l=Sum of all lengths/traverse parame...

Q: 2) Upon completion of the excavation, backfilling and compaction works for the proposed road describ...

A: Given data: Concrete mix Ratio. 1:1.75:1.7+Admixture 1 cubic meter of concrete for given mix 13 bags...

Q: Exercise 6 Analysis Flange beam for s<hf • Determine the ultimate moment of resistance of L- section...

Q: For the simply supported beam subjected to the loading shown, derive equations for the shear force V...

Q: concentration, n rent le

A: Finding Rth - first we will minimise the circuit , then becomes 1Rth =110 k+110...

Q: The volume of ocean water is 1338x10° km³. The runoff from rivers is 44.7 x10³ km³/year and the runo...

A: Hello dear this is the solution of your problem The answer is found to be Residence time =2646 years...

Q: Calculate the slope (%) of the watershed to TWO decimal places given the following information: Hi...

Q: 90KN/m 75KN В 9m 21 5m 5m A 75KN 3m Analyze the FRAME using Slope Deflection Method Compute for the ...

A: FIXED END MOMENTS: MAB=0MBA=0MBC=-90×9212=-607.5 KN-mMCB=+90×9212=+607.5 KN-mMCD=-75×5×3282=-52.73 K...

Q: From the Figure, determine the equation of moment and what would be the value of moment if X = 5 m a...

Q: Determine the deflection at the free end I = 362500Kft´. Use Castigliano's Theorem.

Q: en TP1 and TP2. Assume stadia interval factor equal to 100 and instrument constant equal to zero. IO...

Q: Determine normal force exerted on block by the surface at point A and B

Q: Problem B Using AASHTO, classify the following soil SAMPLE SIEVE SIEVE SIEVE SIEVE LL PL NO.200 NO.4...

A: GIVEN 5 soil sample And their percentage Passing through seives And liquid limit and plastic limit. ...

Q: A cylindrical tank, having a vertical axis 6ft in diameter and 10ft high. Its sides are held in posi...

A: Given:- The diameter of the cylindrical tank = 6 ft The height of the tank = 10 ft The sides of the...

Q: A steel column consisting of a ISHB 350 @ 710.2 N/m, 3.5 m high. The column is restrained in directi...

Q: A man bought a lot worth P2.1M if paid in cash. On the installment basis, he paid a down payment of ...

Q: A 3.5 m square footing is proposed to be used to support a 328 mm x 328 mm RC column loaded with 815...

Q: A clean quartzic sand (Gs = 2.69) has a dry unit weight of 14 kN/m³ at a moisture content of 7%. A s...

Q: Starting at the island of Moi in an unknown archipelago, a fishing boat makes a round trip with two ...

Q: The aluminum rod AB (Gaj = 27 GPa) is bonded to the brass rod BD (Gpr = 39 GPa). The portion CD of t...

Q: Shown in figure below is the front elevatlon of a stable stone arch. The stone blocks are shaped to ...

A: Stones is a type of brittle material.

Q: Perform the indicated operation: (-2-2i)/(6-6i)

A: indicated operation: (-2-2i)/(6-6i) We know, i2 = -1 (a + b)2 = a2 + 2ab +b2 (a -b)(a+b) =a2 - b2

Q: An intenal column in a multi-storey building has an actual length of 4.2 m centre-to-centre of tloor...

A: As per Section 4.14 of BS 5950 : Part 1, The compression resistance of column which is cased is give...

Q: Which of the following steel shapes would you use as a tension member? Neglect loading conditions.

A: Option A is correct.

Q: Find the equation of the circle if it is tangent to the line x + y = 2 at point (4 -2) and the cente...

Q: Find the total distance (m) traveled by a car from the time he saw a hazard until he applied the bra...

Q: A cantilever beam of length L and a cross-section with shape factor 1.5 supports a concentrated load...

A: Given arrangement, The Length Lp of the plastic zone, when the maximum bending moment equals the ...

Q: or a full station of 20m and the stationing of the vertex is 5+005.25m, using arc basis determine th...

Q: A flat slab is supported on 600 mm dia circular columns spaced 8 m x 6 m apart in both directions. T...

Q: Which of the the following is the most important property of an axially loaded column? O KL/r O Sy O...

Q: The steel beam has the cross section shown. The beam length is L = 30 ft, and the cross-sectional di...

Q: the hoops, find tension in each hoo

A: v =π4×D2×H Take V =450 m3assume D =12 m450 = π4×122×H⇒H =3.47≃4 m 1 design of top dome Merielonal ...

Q: Determine the total volume for excavation, concrete embedded, embankment and disposal. Inidicate min...

A: All moments and forces acting at the base of the column must be transferred to the pedestal, if any ...

Concept explainers

Planar Stresses

Question

The beam is supported by two rods AB and CD that
have cross-sectional areas of 12 mm2 and 8 mm2
respectively. Determine the position d of the 6 kN load
so that the average normal stress in each rod is the
same.
B
6 kN
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The simply–supported beam is loaded as shown. Use P = 8 kN and Q = 12 kN. Draw the shear and moment diagram. Plot the flexural stress distribution at point of maximum moment.
Determine the shear stress (in Mpa) in the 20.75-mm-diameter pin at A that support the beam if P = 28.96 kN, a = 2.12 m, and b = 5.72 m. Round off the final answer to three decimal places.
1.) Draw the internal stress and strain diagram of beam considering that the depth of the stress block is greater than the thickness of the flange. f’c =30 MPa, fy=400 MPa and is subjected to a positive bending Mu=140KN-m.
If Mz = 545 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 10 in. b = 14 in. d = 35 in. r = 5 in. The centroid of the cross section is located 16.07 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 44269 in.4.
If d = 450 mm, determine the absolute maximum bending stress in the overhang beam.
From the given simply supported beam below, determine the following: d. The moment of inertia with respect to the neutral axis. e. The maximum flexural stress and shear stress of the beam. f. The bending stress at point B and C.
Member AB has a uniform rectangular cross section of 10 x 24 mm. For the loading Pshown,a) Find reactions at A and B.b) Determine the normal and shearing stresses at Point K and Point H. α (˚) =30 P (kN)=14
A simply supported beam has a concentrated load at midspan. If the beam properties are given below, what is the final stress at bottom of the beam section where the maximum moment is located and the total losses of the prestressing force is 21% (MPa) Properties: Beam width = 289 mmBeam height = 498 mmConcentrated load = 22.79 kNSpan of the beam = 9 mPrestressing force = 385 kNeccentricity = 123 mm
If M, = 285 kip-ft, find the magnitude of the bending stress at a point H For the beam cross section, assume a = 9 in. b= 12 in. d= 31 in r= 45 in. The centroid of the cross section is located 14.16 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 26227 in 4
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.
Determine the minimum force P to prevent the 30-kg rod AB from sliding. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is μs = 0.2.