The bearing for a power transmission arrangement is required to carry an 9.8 equivalent radial load of 2.4 kN at 3000 rpm. The nominal shaft diameter at the bearing is 30mm. A life of 8760 hours is required. Select and specify an appropriate bearing from the limited range available in Tables 9.6 to 9.8.

The bearing for a power transmission arrangement is required to carry an 9.8 equivalent radial load of 2.4 kN at 3000 rpm. The nominal shaft diameter at the bearing is 30mm. A life of 8760 hours is required. Select and specify an appropriate bearing from the limited range available in Tables 9.6 to 9.8.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Select an angular contact ball bearing to carry a radial load of 336lb at a shaft speed of 1800 rpm for 5500 hours. Anapplicationfactorof1.2isappropriate. Use a reliability of 96%.
Estimate the life in hours of a 02-30 mm angular-contact ball bearing subjected to 20,000 revolutions per cycle. Each cycle consists of a radial load of 15 kN for 6 min, and then a change in load to 25.05 kN for 4 min. Determine the expected life of the bearing, in millions of revolutions, for each load, assuming the bearing has a C10 value of 20.3 kN. The expected life of the bearing for 15 kN load is ___ × 106 revolutions. The expected life of the bearing for 25.05 kN load is ____× 106 revolutions.
A Self-aligning medium series bearing for bores of 85 mm is operating at 300 r.p.m for an average life of 9 years at 10 hours per day, is acted by a 15 kN radial load and 10 kN thrust load. The bearing is subjected to a light shock load and the inner ring is sationary. Determine the suitable self-aligning bearing. Mention the advantage of using self align bearing.
A single deep grove ball bearing series 3, the outer ring rotates at 1500 rpm with little shock load. Bearing has a bore diameter of 45 mm, working with a load 1890 lb radial and 1250 lb axial load. Determine the rated life and median life of the bearing. Use the design factors according to the attached table.
b) Design a single row deep groove ball bearing with basic dynamic load rating of 33 KN to be used in a turbine to carry a radial load of 1584 N. The expected life of the bearing is 5591 hours at 529 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in N
A propeller shaft rotating at constant speed is subjected to variable loads.Ball bearing supporting the shaft are subject to variable radial loads as follows;16KN for 40 percent of the time,2KN for 10 percent of the time,4KN for 20percent of the time and no load for the remaining time of the cycle.The total life expected for bearing is 3×10^6 revolution at a liability of 94 percent.select the bearing by calculating; a)Net dynamic load for the bearing b)load rating of the bearing from the manufacturers catalogue
Calculate the SKF rating life at 95% reliability for the following thrust ball bearing and conditions. Fa: 5.17 kNn: 1497 rpmBearing 51110Clearance NormalaSKF: 1 Give the answer in hours.
Select an angular contact ball bearing to carry a radial load of (336+9) lb at a shaft speed of 1800 rpm for 5500 hours. An application factor of 1.2 is appropriate. Use a reliability of 96%.
An 02-series ball bearing is to be selected to carry a radial load of 8 kN and a thrust load of4 kN. The desired life LD is to be 5000 h with an inner-ring rotation rate of 900 rev/min. Whatis the basic load rating that should be used in selecting a bearing for a reliability goal of 0.90?
A double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to raise the load without friction effect? Group of answer choices 66845 N-mm 133690 N-mm 236078 N-mm 334840 N-mm
A designer is selecting a ball bearing for a particular application, which requires the bearing to operate for 24 hours/day and 180 days at a speed of 200 rpm. What is the required catalog load rating (in lbf) for the reliability of 0.90 if the radial design load is 450 lbf, assuming the catalog life is 106 revolutions? choose answer below 09*10^3 0.9*10^3 2.44*10^3 4.8*10^3
A single row deep groove ball bearing is operating at a speed of 2000rpm acted upon by a radial load of 10kn and thrust load of 8kn. The bearing is subjected to light shock load and outer ring is rotating. Determine the life rating of the bearing