The bent rod ABDE is supported by ball-and-socket joints at A and E and by the cable DF. If a 145-lb load is applied at C as shown, determine the tension in the cable. z = 25 in. Write numerical value only and in 2 decimal places. 8 in. F 7 in. 9 in. A B 11 in. C E 16 in. 14 in.

The bent rod ABDE is supported by ball-and-socket joints at A and E and by the cable DF. If a 145-lb load is applied at C as shown, determine the tension in the cable. z = 25 in. Write numerical value only and in 2 decimal places. 8 in. F 7 in. 9 in. A B 11 in. C E 16 in. 14 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: D 4 3

Q: For the beam and loading shown, determine the tension in the cable and the support reactions at…

Q: Determine the tension in cables AC and BC, and reaction at the ball and socket joint at O if the…

Q: The 10-lb bar AE is suspended by a cable that passes over a 5-in.- radius drum. Vertical motion of…

Q: 3. Find the tension in the cable BC (15 pts) 12 ft 9ft 10,000 Ibs 12 ft 4. Find the reactions at…

A: Moment at hinge is zero

Q: The system in the figure is in equilibrium. Aconcrete block of mass 349 kg hangs from the end of the…

Q: C A 3 4. 45° В D

A: From the above figure Inclination of BC to Horizontal= 45° Similarly inclination of AB=…

Q: ring at B. Khowing tens: le is 385 N, determine the components of the force e cable on the support…

A: According to given data in the figure below

Q: 3. The cable supports the loading shown. Determine the magnitude of the horizontal force P so that…

Q: THE 6-M POLE ABC IS ACTED UPON BY A 455- N FORCE AS SHOWN. THE POLE IS HELD BY A BALL-AND-SOCKET…

Q: A Beam AB is supported by a pin at A and cable BC at B. The force developed in cable BC is. 250 N…

A: Step 1

Q: Figure 2-83 7. Determine the maximum sag and the largest tension in 4k 24 1 4k the 30 ft 30 ft 30 ft…

Q: For the cable assembly presented, the member ABC is assumed to be rigid and is pinned at A. Also, it…

Q: Determine the force P on the cable if the spring is compressed 0.5 in. when the mechanism is in the…

A: The given figure is shown below:

Q: 3. A uniform circular rod of weight 8-lb and radius 10 inch is attached to a pin at C and to the…

Q: ind the force P and the cable tension AB as shown. FLOOR SLAB W- 2*

A: To find force P and tension in cable AB

Q: A distributed load that varies from 20 kN/m to 50 kN/m is applied as shown in the figure.…

Q: The bent rod ABDE is supported by ball- and-socket joints at A and E and by the cable DF. If a…

Q: Weight W is supported by spring OC, which is attached to two cables at O. The un-stretched length of…

Q: Determine the magnitude of the resultant force acting on the bracket. F = 450 N 45° 30 60 45 F2 =…

A: force component in x…

Q: D (0,6, 0) m (12, 4, 2) m C B (6, 0, 0) m ーメ (0, 4, 6) m

Q: 12 m 4 m 5 m B W2 Fig. P6.88, P6.89 6.89 The cable of length 15 m supports the forces Wi = W2 = W at…

A: From geometry resolve the length of cable in vertical and horizontal direction;

Q: Та Tb 15° 30° Td Tc 60° 75° W

Q: Cable AB is supported by a truss structure at A and a pin at B. A uniform distributed load is…

A: 50

Q: 5. The turnbuckle is turned until the | tension in the cable AB reaches the D value represented by…

Q: PROBLEM 1.Thestructure shown is held in equilibrium by a cable and fixed support at A. Calculate the…

A: Draw F.B.D 4.52+62=7.5cosθ=4.57.5 , sinθ=67.5

Q: A cable is attached to the 20-kg plate B, passes over a fixed peg at C, and is attached to the block…

A: Draw the free body diagram of the block A.

Q: The boom supports the two vertical loads. Neglect the size of the collars at D and B and the…

Q: The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at…

A: Given, Magnitude of tension in cable BE, say TBE = 204 N To determine the magnitude of force P.…

Q: F1=100N Let F₁ = [F1] N and let F₂ = 350 N. g) Determine the magnitude FA of the force at pin A. h)…

A: Given:F2=350 NSupport A is a hinge support.Therefore, there will be two support reactions( 1…

Q: A 90-lb load is suspended from the hook shown . If theload is supported by two cables and a spring…

A: Given: The load is 90 lb. The stiffness of the spring is 500 lb/ft. Consider the figure,

Q: Determine the velocity of D if end A of the rope is pulled down with a speed of 3 m/s. B nodulo VA =…

Q: Determine the tension in cable BE .and the reactions at A and D

Q: ROBLEM 1: Determine the mass of the heaviest uniform bar that can be supported in the position s the…

A: x=1m T=15.5kN

Q: 4m 4m 2m 1 P.

Q: 4. For the beam and loading shown, determine the tension in the cable and the support reactions at…

Q: A cable-supported roof carries a uniform load w kip/ft. If the cable sag at midspan is set at 10 ft,…

Q: 3. The cable BC carries a tension of 800 N. Write this tension as a force T acting on point B in…

Q: AC B 25 45°

A: Two cables are tied together at C and are loaded as shown. Knowing that P = 500 N and angle alpha is…

Q: The homogeneous 860-kg bar AB is supported by a ball-and-socket joint at A and two cables attached…

A: Question is based on the bar is given which is supported by a ball and socket joint . Mass of bar…

Q: The sphere of weight, W = 68.67 N, is suspended by a cable with length, a = 3 m as shown. If it rest…

Q: 6. The two blocks are placed on the inclined with the cable taut. Determine the force P 3/4 required…

Q: The system in the figure is in equilibrium. A concrete block of mass 232 kg hangs from the end of…

A: Take moment about hinge:Tsinθ-ϕL-mgL2cosθ-m'gLcosθ=0

Q: Determine the tension P in the cable which will give the 107-lb block a steady acceleration of 4.4…

Q: efer to the figure below. Diagonals BG, CF, CH, and DG are flexible cables F G 1.5 kN 3 m B E 3 m 3…

Q: Determine the sag at points C and E on the cable in the figure below (Sag at point D is given), and…

A: GIVEN- L=160ft

Q: The 6-m pole ABC is acted upon by a 455-N force as shown. The pole is held by a ball-and-socket…

A: Force Vectors:-A=Axi^+Ayj^+Azk^F=455*-3i^-6j^+2k^32+62+22F=-195i^-390j^+130k^ N

Q: D 3 ft 5 ft 5 ft B The homogeneous 6000-lb bar ABC is supported by a pin at C and a cable that runs…

A: Given data in question Span member length Weight of Bar Hinge at point C Diameter of cable To find…

Q: The bent rod ABDE is supported by ball-and- socket joints at A and E and by the cable DF. If a…

Concept explainers

Laws of Equilibrium

A body is said to be in equilibrium if the system of forces acting on the body tends to keep the body at rest, in other words, there is no translation motion or net torque on the body. Under such conditions, the equilibrium conditions are to be applied to analyze the condition. The branch of mechanics that deals with this condition is known as 'statics'. Under equilibrium, there are no net forces on the body.

Question

The bent rod ABDE is supported by ball-and-socket joints at A and E and by the cable DF. If a 145-lb load is applied at C as shown,
determine the tension in the cable. z = 25 in. Write numerical value only and in 2 decimal places.
8 in.
7 in.
9 in.
В
11 in.
C
xr
E
16 in.
14 in.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. The force along the cable AB is 10 kN. Represent the force in vector Cartesian form.2. The Cable BC carries a tension force of 500 kN. Find the components of the tension force along BA and perpendicular to BA.3. If the plate is to remain in equilibrium, find the tension for all the three cable that supports the plate weighing 2200kg. 4. The block weighs 3500 kg. Find force in members AB, AC and AD.
A cable ABCD is pulled at end E by a force P (Figure P6.12). The cable is supported at point D by a rigid member DF. Compute the force P that produces a sag of 2 m at points B and C. The horizontal reaction at support F is zero. Compute the vertical reaction at F.
The 6-m pole ABC is acted upon by a force P as shown. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. If the tension in cable BE is 204 N and if a = 3m, determine the magnitude of force P(N). Round off only on the final answer expressed in 3 decimal places.
Determine the tension in the cable at B, given that the uniform cylinder weighs 350 lb. Neglect friction and the weight of bar AB.
2, The rigid body ABC is held in place by ball and socket joints at A and C, and cable DE which passes through the right at point B. Find the tension in Cable DE. The coordinates of the points in (mm) are as follow: A, (0,0,600) B, (600,0,600) C, (800,0,0) D, (0,500,300) E, ( 800,500,0) F, (800,0,600)
The cross section of a rectangular gate AB of width 2 m is shown in Figure2. The weight of the gate is 1 kN and is hinged along BB. The maximumtensile force that the cable can hold is only 44kN. Calculate the maximumwater depth, y that causes the cable to break and will cause the gate tofail/ open.
P1 = 3.9 kN, P2 = 6.3 kN a) Determine the force P needed to hold the cable in the position shown, so segment BC remains horizontal b) compute sag yB. c) compute the maximum tension in the cable.
A cable is attached to the 20 kg plate B, passes over a fixed peg at C, and is attached to the block at A. Using the coefficients of static friction shown, determine the smallest mass of block A so that it will prevent sliding motion of B down the plane.
A T-shaped simple beam has a cable with force P anchored at B and passing over a pulley at E as shown in the figure. The bending moment just left of C is 1.25 kN-m. The cable force P is approximately:
13. A 12-m pole supports a horizontal cable CD and is held by a ball and socket at A and two cables BE and BF as shown in Figure 2. Knowing that the tension in cable CD is 14 KN and assuming that CD is parallel to the x-axis (0), determine the horizontal component of the reaction at A. A. 7.00 kN B. 17.50 kN C. 22.4 kN D. 2.50 kN
Compute the support reactions for the arch in Figure P6.25. (Hint: You will need two moment equa- tions: Consider the entire free body for one, and a free body of the portion of truss to either the left or right of the hinge at B.)
Compute the vertical components of the hinge forces at C as they act upon member AC in kN P= 89 kN and x= 3.7 m. Write numerical value only and in 2 decimal places