The bicycle and rider shown in (Figure 1) have a mass of 80 kg with center of mass located at G. The coefficient of kinetic friction at the rear tire is μg 0.8. Figure G 0.55 m 0.4 m- < 1 of 1 1.2 m Determine the normal reaction at the tire A, when the rear wheel locks for braking. Express your answer to three significant figures and include the appropriate units NA = Submit Part B NB = Ii Submit μÃ Value Request Answer Determine the normal reaction at the tire B, when the rear wheel locks for braking. Express your answer to three significant figures and include the appropriate units O T μÁ Value Units Request Answer ? Units ?

The bicycle and rider shown in (Figure 1) have a mass of 80 kg with center of mass located at G. The coefficient of kinetic friction at the rear tire is μg 0.8. Figure G 0.55 m 0.4 m- < 1 of 1 1.2 m Determine the normal reaction at the tire A, when the rear wheel locks for braking. Express your answer to three significant figures and include the appropriate units NA = Submit Part B NB = Ii Submit μÃ Value Request Answer Determine the normal reaction at the tire B, when the rear wheel locks for braking. Express your answer to three significant figures and include the appropriate units O T μÁ Value Units Request Answer ? Units ?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.49P

See similar textbooks

Similar questions

The single-plate clutch transmits the torque C from the input shaft on the left to the output shaft on the right. Compression springs between the clutch housing and the pressure plate provide the necessary pressure on the friction surface. The splines prevent the clutch plate from rotating relative to the output shaft. If Ri=4 in. and R0=9 in., determine the total force that must be applied to the pressure plate by the springs if the clutch is to transmit a torque of C=56lbft when it is new.
The square-threaded screw 0f the C-clamp has a mean diameter of 8 mm and a pitch of 1.6 mm. The coefficient of static friction between the threads is 0.2. If the torque C=1.50Nm is used to tighten the clamp, determine (a) the clamping force; and (b) the torque required to loosen the clamp.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The horizontal force P = 90 N is applied to the upper block with the system initially stationary. The block masses are mA = 14.4 kg and mB = 5.1 kg. Use g = 9.81 ms-2. Determine the magnitude of the frictional force that block B exerts on block A. The coefficients of static friction are µ1 = 0.40 and µ2 = 0.50. The coefficients of kinetic friction are 75% of the respective static values. Give your answer in Newtons.
The 5.33-kg cylinder is suspended from two equal-length cords (L = 690 mm). The end of each cord is attached to a ring (negligible mass) as shown in the figure. The ring passes along a horizontal shaft. Provided that the rings can be separated by the greatest distance d = 352 mm and still support the cylinder, determine the coefficient of static friction between each ring and the shaft. The only answer is 0.264. Thanks.
The crate shown has a mass of ? ൌ 15 kg and is pulled by the rope as shown. If the coefficients of static and kinetic friction are ?௦ ൌ 0.30 and ?௞ ൌ 0.20, provide answers for the following. Set ? ൌ 30°.
The block brake consists of a pin-connected lever and friction block at B. The coefficient of static friction between the wheel and the lever is μs = 0.3, and a torque of 5 N ⋅m is applied to the wheel. Determine if the brake can hold the wheel stationary when the force applied to the lever is (a) P = 30 N, (b) P = 70 N Draw the free-body diagram of the lever.
The masses of the blocks are mA = 30 kg and mB = 70 kg. Between all of the contacting surfaces the coefficient of static friction is 0.1. 1. What is the largest force F that can be applied without causing the blocks to slip? 2. What is the reaction between the two blocks? 3. What is the reaction between the floor and block B
The crate has a weight of W = 350 lb, and the coefficients of static and kinetic friction are μs = 0.3 and μk = 0.2, respectively. Determine the friction force on the floor if θ = 47.4° and P = 105 lb.
The homogeneous 322-lb body A of Fig. P10-30 is moving to the right with a velocity of 6 fps. The coefficient of friction between A and the horizontal plane is 0.2. Determine the maximum weight body B may have without causing A to tip.
A 0.8 lb roll of paper is suspended from a wire hanger so that it rests against the wall. The hanger has a negligible weight and the bearing O can be considered as frictionless. The two ends of the hanger can be treated as pin joints. Determine the force P required to start turning the roll if theta = 37 degrees and the coefficient of static friction is 0.29.