The bin is 2 m wide and is filled with oil to the depth shown. Determine the location of the resultant force acting on the inclined side AB from the bottom. Take density of oil = 900 kg/m3. 3 m O 0.74 m 0.92 m 1.45 m 0.58 m

The bin is 2 m wide and is filled with oil to the depth shown. Determine the location of the resultant force acting on the inclined side AB from the bottom. Take density of oil = 900 kg/m3. 3 m O 0.74 m 0.92 m 1.45 m 0.58 m

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.5P

See similar textbooks

Related questions

Q: 2. The torques shown, are exerted on pulleys A, B and C. Knowing that both shafts are solid, determi...

A: Consider shaft AB ; Maximum Shearing stress in Shaft AB will be given by ; Shearing Stress = TAB * r...

Q: Which one is correct? A. Increasing additional load means increasing exposed depth in a fluid. B. De...

Q: In fig. if the datum line taken at point * 1, then Control volume boundary 1-2 21 2 m 200 mm diam 1....

A: According to fig: Datum line taken at point 1 than Z1=0, Z2= 2 m and Z3= - 1.5 m

Q: mine the shear stress in the glued area.

A: We know at certain angle Shear stress=τ=FAsinθcosθ

Q: A machine is bought at P150,000 with an economic life of 6 years and a salvage value of P5,000. The ...

A: Depreciation: every year the value of the machine gets decreases over the usage and time .

Q: The dry density of a sand with a porosity of 38.7% is 1600 kg/m^3. e=0.63; Gs=2.66 Determine the vol...

Q: 2.0 Block A weighs 500.0 N and block B weighs 280.0 N. Block A is held by a cord fastened to the wal...

Q: Determine the force in members DC, HC, and HI of the truss and whether it is in tension or compressi...

Q: 4-ø27 mm bars? The yield strength of its reinforcer ed compressive of concrete is 22 MPa.

A: data given fc =22 MPafy=296 MPab =344d=591Minimum steel reinforcement is given by as , Astmin =0...

Q: 40 fé = 3000psi %3D ダク 26" 14 14 fy = 6o ksi %3D 8#8 12 NWC PMa = ?

A: A beam with T section is given in the above question. The value of fc' and fy is provided. also the ...

Q: At which temperature in degree celsius of fluid water is the reference for measurement of specific g...

A: A factual data based question is asked, please refer step 2 for detailed explanation and solution.

Q: Ricky has a sedimentary rock sample with a specific gravity of 2.68. Based on the table, we can infe...

A: In the sedimentary rock type we will check for specific gravity.

Q: Two cantilevers beams of same cross-section and separated by a roller jointly support a uniformly di...

Q: Two 10 KN forces are applied to a 20x lo0 mm rectangular bar, as shown. stress at (6) b-15mm, (c) b=...

Q: A student deposits P1,500 in a 9% account today. He intends to deposit another P3,000 at the end of ...

Q: The balloon shown in the figure is filled with helium pressurized to 111 kpa. Compute the tension in...

A: Tension will be equal to bouyancy force.

Q: Are roundabouts applicable for high speed approaches? Find an example on line. from Highway Enginne...

A: Roundabouts are only applicable for slow speed approaches ..

Q: The field capacity of a soil is 35% by weight, and the wilting point is 15% by weight. If the dry bu...

Q: a) Replace the distributed loading with multiple forces. b) Draw the free body diagram for the beam....

A: Given Data -

Q: Figure 4. 300 mm M 30 mm 30 mm 150 mm 150 mm If the beam is made of material having an allowable ten...

A: Given data Allowable Compressive stress = 150 Mpa Allowable Tensile stress =125 Mpa To Calculate...

Q: A soil sample taken from a field contains a volume of 110 cm3 , weighs 220 grams when taken, and 165...

Q: The field capacity of a soil is 35% by weight, and the wilting point is 15% by weight. If the dry bu...

A: Given data - Field Capacity of soil = 35% The wilting point is = 15% Dry bulk density of soil 1.25 ...

Q: A sample of soil in its natural state has a volume of 1.396 m3 and weighs 18.662 kN. The sample was ...

A: weight of soil in natural state, w=18.662KNVolume of soil, V =1.396m3After oven drying, weight of so...

Q: If the concentration of Na, Ca and Mg in a water sample are 345, 60 and 18 mg/l, respectively, then ...

Q: Question 7 The bronze bar 3 m long with a cross-sectional area of 350 mm? is placed between two rigi...

Q: A soil sample taken from a field contains a volume of 110 cm3 , weighs 220 grams when taken, and 165...

Q: A soil has a porosity of 40%, the G-2.5 and water content of 12%. 14. Water content at full saturati...

Q: 1.) Given the following properties of a rectangular concre strength under the following conditions. ...

Q: Four inelastic cables are attached to plate and hold the 1.25-ft- long spring A 0.25 ft in compressi...

A: Given Data -

Q: Question 2 A steel rod having a cross-sectional area of 300 mm? and a length of 150 m is suspended v...

Q: (Problem 5.15 from the text book) For the beam and loading shown, determine the maximum normal stres...

Q: 25. For the truss shown in figure A, what is the reaction RBy at node B? A. 1,000 lb B. 1,500 lb C. ...

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since ...

Q: 4. a) Replace the distributed loading with multiple forces. b) Draw the free body diagram for the be...

Q: Construct the shear-force and bending-moment diagrams for the beam shown. Assume a = 4.4 ft, b = 8.8...

Q: Determine the shear and moment at points B and D of the beam shown.

A: Given Data -

Q: A building has to be supported over a raft foundation of dimensions 15 m x 25 m. The soil is clay ha...

Q: determine the required diameter of the steel and aluminum rods.

A: Torque: - It is type of force which produces rotational motion in a body. Also called as rotational ...

Q: A involves the determination of the value of a specified variable that will make the revenues exactl...

A: A multiple choice questions is given and it has been asked to choose appropriate option. Please refe...

Q: he Mood Design a column to support an axial load of 700 kN. The column has an effective length of 7 ...

A: Given data, Axial load = 700 kN Fy = 250 N/mm² Design a column to support an axial load of 700 kN...

Q: 85. A shaft turns at 200 rpm under a torque of 1800 Nm. The power transmitted is

A: We have to determine the value of power transmitted as per the given data like 200 rpm shaft speed a...

Q: In fig. if the pipe diameter = 25 mm, * ?---=V2= 6m/s , Q=--? h U-tube Liquid Z, Elevation reference...

A: Given- Pipe diameter (D) = 25mm Velocity of liquid at point 2 (V2) = 6m/s Calculate- Disc...

Q: Calculation question: Two side fillet welding int, N=660 kN (static loading, design value), sing ang...

Q: 4KN/m 10KN 8KN - 6m - 2m - 2m 4m 2m Using Moment Distribution Method: Draw Shear and Moment Diagram

Q: The journal bearings at A and B only support vertical forces. The allowable stress is 173 MPa. Deter...

A: Given

Q: Refer to the figure below. Ao,, at point A with the following values: q1 = 120 kN/m; q2 =350 kN/m; x...

Q: The given data of a proposed Manila-Cavite Coastal Road is tabulated below. The tree ha istance is 5...

A: The given data is: Hall distance=50 m Cost of borrow=420 php/m3 Cost of excavation=350 php/m3 Cost o...

Q: A 200 meter parabolic curve has a grade of -4% and +6%. The two grades intersect at 5+600 with eleva...

A: We have to determine the value of elevation of the top of the culvert pipe if backfill depth is 0.60...

Q: A building has to be supported over a raft foundation of dimensions 15 m x 25 m. The soil is clay ha...

Q: - A pipe has what is the

Q: HI = 1.496 ELEVATION OF PT A: = 200 K = 99 HAIR READING MIDDLE LOWER 1.589 VERT. STADIA DISTANCE STA...

Concept explainers

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.

Question

100%

ASAP show compelte and clear solution. Dont round off initial values, round off final ans only pls. (Select answer in the choices)

The bin is 2 m wide and is filled with oil to the depth shown. Determine the
location of the resultant force acting on the inclined side AB from the
bottom. Take density of oil = 900 kg/m3.
3 m
60
O 0.74 m
0.92 m
1.45 m
0.58 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the horizontal and vertical components of the hydrostatic force (magnitude and direction) on the half cylinder AB for a unit distance normal to paper. γ1 = 8 kN/m3, γ2 = 12 kN/m3 h1 = 4 m, h2 = 2 m R = 2 m
An open tank 3m by 3m in horizontal section weighs 4 kN and contains water to a depth of 1m. It is acted by an unbalanced force of 18 kN parallel to the pair of sides. a) Determine the acceleration of the tank. b) What must be the height of the tank so that no water will spill out? c) If the acceleration is increase by 4m/s2 , how much water will spill out?
An open horizontal tank 2 m high, 2 m wide and 4m. long is full of water. a) How much water is spilled out when the tank is accelerated horizontally at 2.45 misec in a direction parallel with its longest side? b.) What is the porce acting on the side with the greatest depth? c.) Compute the required accelerating force.
The tank shown in the figure is 3 m wide into the paper. Neglect atmospheric pressure. Use ?????? = 9.79 kN/m³. Determine the following: A. vertical component of the total hydrostatic force on the quarter circle panel AB in kN B. Resultant hydrostatic force acting on the quarter circle panel AB in kN C. Angle that the resultant hydrostatic force make with the horizontal in degrees.
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=75° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm2 and A=50 cm2 shall be taken for all rods.)
A loaded scow 6 m wide, 12m long and 2.4 m high has a draft of 1.8m in fresh water when upright. The center of gravity of the scow is 1.8 m above the bottom along vertical axis of symmetry; (a) What is the angle of tilt if the scow tilts due to a load placed or moved transversely to the right from the center without sinking it as it rolls over the side? (b) What is the weight of the load described in letter a
If a triangle of height d and base a is vertical and submerged in liquid with its vertex a distance below the liquid surface, determine the depth to its center of pressure. What is the horizontal force acting on the triangle? Assume ? water = 9790 N/m3. f = depth to apex, 2m d = height of triangle, 1m a = width of triangle, 1m The horizontal force (N) acting on the triangle is:
In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=30° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm² and A=50 cm² will be taken for all bars.)
Calculate the horizontal displacement of point B. EI is constant for all members (p=50kN , W=90KN/m , h=7m , b=5 m) I need a solution within 40 min
The bin is 2 m wide and is filled with oil to the depth shown. Determine the resultant force acting on the inclined side AB and the location of the resultant force acting on the inclined side AB from the bottom. Take density of oil = 900 kg/m3.
The rectangular bin with an inclined gate AB is filled with oil to the depth shown. Determine the resultant force (kN) acting on the inclined side AB. Take density of oil - 900 kg/m^3 x=3.27 a=5.2 m b=30 degrees asap
Describe the Position of lateral pressure resultant for stability analysis.